Unsteady shock-induced separation of the ramp boundary layer was reduced and stabilized more effectively by external perforations than by external or internal slots. At Mach 2.0 peak total-pressure recovery was increased from 0.802 to 0.89 and stable mass-flow range was increased 185 percent over that for the solid ramp. Peak pressure recovery occurred just before instability. The 7 and one-third-diameter duct ahead of the engine reduced large total-pressure distortions but was not as successful for small distortions as obtained with throat bleed. By removing boundary-layer air the bypass nearly recovered the total-pressure loss due to the long duct.

Report presenting the performance of a side inlet with a fixed 12 degree two-dimensional compression surface for a range of Mach numbers, angles of attack, and yaw. The effects of several methods of compression-surface boundary-layer removal were investigated as well as a solid ramp.

Report presenting an investigation to determine the blade torsional deflection of three supersonic-type propellers at various operating conditions. Blade-torsional deflection was found to produce appreciable results that can be predicted by theory with good accuracy. Results regarding the efficiency, thrust coefficient, and power coefficient are provided.

Free flight test of tailless missile configuration with 45-deg sweptback wing of aspect ratio 4 - stability at transonic speeds. The longitudinal flexible-wing results indicated a gradual transonic trim change a lift-curve slope comparable with that for the same configuration with a wing of aspect ratio 5.5. Results regarding trim characteristics, lift and longitudinal stability, and side-force and lateral stability are provided.

Memorandum presenting a flight test of a long-range missile configuration with a 45 degree sweptback wing of aspect ratio 4 conducted at a range of Mach and Reynolds numbers. The longitudinal flexible-wing results indicated a gradual transonic trim change and a lift-curve slope comparable with that for the same configuration with a wing of aspect ratio 5.5.

Report presenting tests of two models of an inline, cruciform, canard missile configuration with a low-aspect-ratio wing equipped with flap-type controls to determine the missile's longitudinal aerodynamic characteristics. Stability derivatives and control and drag characteristics are presented for a range of Mach numbers.

Report presenting testing of two full-scale models of an inline, cruciform, canard missile configuration with a low-aspect-ratio wing equipped with flap-type controls to determine the missile's longitudinal aerodynamic characteristics. Stability derivatives and control and drag characteristics are provided.

Report presenting characteristic exhaust-velocity measurements made of the JP-4 fuel-red fuming nitric acid propellant combination in 40-pound-thrust rocket engines with various combustion-chamber lengths and diameters. The results are compared to those from previous studies and discussed in terms of a vaporization model of combustion. Results regarding the effect of UDMH, effect of water on performance of hydrocarbon fuels, effect of water on performance of hydrazine fuel, and some of the chemical and physical factors affecting combustion are provided.

Report presenting measurements of the intensity of buffeting experienced by the Douglas D-558-II research airplane at a range of Mach numbers. Buffeting was encountered at both subsonic and supersonic Mach numbers and the intensity of the buffeting varied with Mach number and airplane normal-force coefficient.

Report presenting testing on a 60 degree delta-wing XF-92A airplane at a variety of Mach numbers to obtain measurements regarding buffet-induced fluctuations in normal acceleration and of fluctuations in structural shear load of the left wing. The altitudes tested ranged from 25,000 to 38,000 feet. Results regarding the buffet boundary, wing flow conditions, buffet frequencies, buffet intensities, and a comparison to buffeting of other airplanes are provided.

Report presenting a method for extending to higher Mach numbers the region of low drag attainable for wing-body combinations by the use of the transonic area rule. To a good approximation, the drag depends only on the longitudinal distributions of area and moments of area about the vertical plane of symmetry parallel to the free-stream direction. The experimental results confirm the theory in that the zero-lift wave drag of a wing-body configuration over a range of low supersonic Mach numbers.

Report presenting tests of the extent of laminar flow that can be obtained with practical wing-surface conditions. Chemical sublimation was used for boundary-layer-flow visualization on the wings of a supersonic fighter airplane in level flight. A method of continuous monitoring using heat temperature resistance gauges was also used on one wing.

Chemical sublimation has been employed for boundary-layer-flow visualization on the wings of a supersonic fighter airplane in level flight at speeds near a Mach number of 2.0. The tests have shown that laminar flow can be obtained over extensive areas of the wing with practical wing-surface conditions. In addition to the flow visualization tests, a method of continuously monitoring the conditions of the boundary layer has been applied to flight testing, using heated temperature resistance gages installed in a Fiberglas "glove" installation on one wing. Tests were conducted at speeds from a Mach number of 1.2 to a Mach number of 2.0, at altitudes from 35,000 feet to 56,000 feet. Data obtained at all angles of attack, from near 0 deg to near 10 deg, have shown that the maximum transition Reynolds number on the upper surface of the wing varies from about 2.5 x 10(exp 6) at a Mach number of 1.2 to about 4 x 10(exp 6) at a Mach number of 2.0. On the lower surface, the maximum transition Reynolds number varies from about 2 x 10(exp 6) at a Mach number of 1.2 to about 8 x 10(exp 6) at a Mach number of 2.0.

Memorandum presenting an investigation conducted in a modified turbojet engine to determine the cooling effectiveness of an air-cooled turbine-rotor blade employing a corrugated metal sheet brazed to the inner surface of the blade shell to increase the internal heat-transfer area. The corrugated fin blade had a lower integrated average wall temperature at the section investigated than the more promising shell-supported blade types previously investigated. Results regarding the temperature distribution investigation and pressure loss investigation are provided.

Memorandum presenting an experimental investigation of four rectangular-throat two-dimensional wedge exhaust nozzles. Three of the nozzles were designed to conform to Prandtl-Meyer streamlines for pressure ratios of 5, 10, and 24, and a fourth, arbitrarily contoured, with a length less than that required for isentropic expansion, was designed for a pressure ratio of about 9.

"In an investigation of the J-33-A-21 and the J-33-A-23 compressors with and without water injection, it was discovered that the compressors reacted differently to water injection although they were physically similar. An analysis of the effect of water injection on compressor performance and the consequent effect on matching of the compressor and turbine components in the turbojet engine was made. The analysis of component matching is based on a turbine flow function defined as the product of the equivalent weight flow and the reciprocal of the compressor pressure ratio" (p. 1).

"Flame quenching by a variable-width rectangular-slot burner as a function of pressure for various propane-oxygen-nitrogen mixtures was investigated. It was found that for cold gas temperatures of 27 degrees C, pressures of 0.1 or 1.0 atmosphere, and volumetric oxygen reactions of the oxidant of 0.17, 0.21, 0.30, 0.50, and 0.70, the relation between pressure p and quenching distance d is approximately given by d (unity) p (superscript -r) with r = 1, for equivalence ratios approximately equal to one. The quenching equation of Simon and Belles was tested" (p. 1).

"An investigation of the spin and recovery characteristics of a 1/24-scale model of the McDonnell XP-88 airplane has been conducted in the Langley 20-ft free-spinning tunnel. Results of tests with a conventional tail have been previously reported; the results presented herein are for the model with a vee tail installed. The effects of control settings and movements on the erect and inverted spin and recovery characteristics of the model. In the normal loading were determined" (p. 1).

Report presenting an investigation conducted in the 8-foot transonic tunnel to determine the longitudinal stability and control characteristics of a 0.09-scale model of the Bell X-5 research airplane. Lift, drag, pitching-moment, elevator hinge-moment, and pressure-distribution results are presented for a range of Mach and Reynolds numbers. Results regarding lift and drag characteristics, longitudinal stability and control characteristics, dynamic-response characteristics, elevator hinge-moment characteristics, and mass-flow characteristics and pressure distributions are provided.

Report presenting the results of an investigation to develop a metal-bonding adhesive with improved heat-resistant properties. The most promising results were obtained with a formulation of a phenol resin and epoxy resin with certain heat stabilizers and catalysts. Results regarding the strength of bonds, resistance of adhesives to aging, and heat-resistant properties are provided.

Report discussing testing on a scale model of the Convair XF2Y-1 airplane with solid-fuel rocket motors that simulate full-scale turbojet-engine characteristics at a height of 35,000 feet with full afterburning at Mach number 1.53. The model was found to have dynamic lateral instability, but these results were not likely to be found in a full-scale airplane. Information about the pitching moment, directional stability, lift-curve slope, and drag coefficients is provided.

Report presenting wind-tunnel tests up to a Mach number of 0.85 to determine the effects of wing-tip gun turrets on the aerodynamic characteristics of a typical bomber-wing model. Lift, drag, and pitching-moment data are presented for the wing alone; for the wing with the turrets in the clean condition; and for the wing and the turrets with guns and sighting equipment. The turrets had negligible effect on the lift and pitching-moment characteristics of the wing.

Report presenting a theoretical analysis of thrust augment of turbojet engines by tail-pipe burning and charts from which the thrust augmentation produced may be evaluated from the normal engine data and performance of the tail-pipe burner. Results regarding general curves and illustrative curves are provided.

Memorandum presenting a high-flow sonic-inlet compressor rotor employing double-circular-arc blade sections that was designed and tested in Freon-12. Results regarding overall performance, radial distribution, and blade-element performance are provided.