Report discussing about 400 references pertaining to the hydrodynamic design of seaplanes have been compiled, and the information is presented in the form of abstracts classified under six main headings.

From Introduction: "The purpose of the present paper is to present results obtained recently relating to the characteristics of a full-span sharp-edge spoiler with an 0.02-chord projection above the wing surface at several chordwise positions and also to the relative effectiveness of the sharp-edge spoiler and a wedge-type spoiler located at the 80-percent-chord line."

From Introduction: "Presented in this report are the basic data obtained from investigation. The data are presented with limited analysis in order to expedite their availability to those concerned with jet-exit-afterbody design."

Report discussing tests to determine the aerodynamic characteristics of a model of a 45 degree swept-wing fighter airplane and to determine the loads on attached stores and detached missiles. An investigation into aileron-spoiler effectiveness, aileron hinge moments, and the effects of wing modifications of aerodynamic characteristics was also carried out at various Mach numbers. Results are presented, but caution is provided in regards to extrapolating results from the model onto a full-scale aircraft.

Memorandum presenting an investigation in the Unitary Plan wind tunnel to determine the aerodynamic characteristics of a model of a 45 degree swept-wing fighter airplane, and to determine the loads on attached stores and detached missiles in the presence of the model. Results also included a determination of aileron-spoiler effectiveness, aileron hinge moments, and the effects of wing modifications on model aerodynamic characteristics. The results are presented with minimum analysis.

From Introduction: "In order to obtain some insight into the relative merits of canard and outboard-tail control systems at supersonic speeds, a preliminary investigation of a generalized canard and outboard-tail model has been conducted in the Langley 4- by 4-foot supersonic pressure tunnel at a Mach number of 2.01 and the results are presented herein."

Report discussing a particular wing-body combination that is part of a larger investigation to determine the lift, drag, pitching moment, and root bending moments for various configurations. Information about the aerodynamic characteristics at the tail plane is also provided.

From Introduction: "This paper presents the results of the investigation of the wing-alone and wing-fuselage configurations employing a wing with the quarter-chord line swept back 60^o, aspect ratio 2, taper ratio 0.6, and an NACA 65A006 airfoil section parallel to the free stream."

Report presenting an investigation in the supersonic pressure tunnel at two Mach numbers to determine the aerodynamic characteristics of several jet-spoiler controls on a wing having a 45 degree sweepback of the quarter-chord line, an aspect ratio of 3.5, a taper ratio of 0.3, and an NACA 65A005 airfoil section. Testing indicated that the jet-spoiler effectiveness increased with increasing angle of attack and correlated well with the momentum of jet flow.

From Introduction: "This paper presents the results of an investigation conducted in the Langley 11-inch hypersonic tunnel to evaluate methods of increasing maximum lift-drag ratio."

Report presenting an investigation to determine separately the aerodynamic characteristics of a Douglas Aircraft Company store and a semispan delta-wing-fuselage configuration in the presence of one another. The store was located at the 50-percent-semispan station with the store nose both ahead of and behind the wing leading edge for two longitudinal and three vertical positions.

Report presenting the air-flow behavior over the wing of an XP-51 airplane including photographs of tufts attached to the wing surface and chordwise pressure distributions. A comparison of tuft studies from flight results are compared with results from wind-tunnel testing. Three types of flow were observed: steady flow, unsteady flow, and break-away flow are provided.

From Introduction: "In this study wide variations in many of the pertinent aerodynamic were investigated at subsonic and supersonic speeds. The effects of large changes in principal axis inclination and mass distribution are also included. The primary purpose of this paper is to summarize the information obtained from the analog calculations and to compare the results with the trends predicted from a slightly modified version of reference 2."

From Introduction: "An analytical evaluation of the effects of inlet losses on the net thrust and the fuel economy of an axial-flow-compressor type turbojet engine with a two-stage turbine is presented herein. The analysis is based on engine performance characteristics that were determined from experiments in the NACA Cleveland altitude wind tunnel (references 1 and 2). The experimental investigation did not include tests in which inlet losses were systematically varied, but the effects of these losses can be accurately estimated from the experimentally determined performance characteristics of the engine."

Memorandum presenting an analysis of the effect of adding fluorine to the Vanguard first-stage oxidant. An increase in specific impulse of 5.74 percent may be obtained with 30 percent fluorine. Charts are provided regarding the vehicle performance increases for a zero-drag vertical trajectory.

From Introduction: "This report presents data pertinent to the problem of boosting rocket performance by adding up to 30 percent liquid fluorine to the liquid oxygen of an existing oxygen-hydrocarbon rocket engine."

Report presenting the use of Von Karman's two-dimensional transonic similarity law as applied to drag data of three different thickness wings with NACA 65-series sections and aspect ratios of 7.6 over a range of Mach numbers. The correlation was found to be satisfactory, with results better in the subsonic range than in the supersonic range.

From Introduction: "The purpose of this paper is to present an analytical method for the design of two-dimensional related selection of a blade for particular rotor conditions may be made quickly and easily and its performance deduced from tests of representative sections in cascade."

"An investigation of a single-annulus turbojet combustor with slot-type air admission was conducted to demonstrate the application of certain design principles to the control of outlet-gas temperature distributions. Comparisons of performance of a one-quarter-annulus combustor (duct-type installation) and a full-annulus combustor (obtained in a full-scale turbojet engine) are presented to indicate the applicability of results obtained from combustion studies conducted in duct-type installations. A reasonable correlation existed between the performance of the one-quarter-annulus and full-annulus combustors except for temperature distribution" (p. 1).

Report presenting testing of a number of materials and shapes in two supersonic free jets at stagnation temperatures of up to 4,210 degrees Fahrenheit. Some testing was conducted in a supersonic chemical jet and some was conducted in a ceramic-heated air jet. Materials tested included aluminum alloy, copper, Inconel, magnesium, mild steel, molybdenum, stainless steel, titanium, alumina, zirconia, graphite, bakelite, and nylon.

Combustion blow-out velocities were determined for JP-4 solutions containing: (1) 10 % ethylene - decaborane reaction product, (2) 10% and 20% acetylene - diborane reaction product, and (3) 5.5%, 15.7%, and 30.7% methylacetylene - diborane reaction product. These were compared with blow-out velocities for JP-4, propylene oxide, and neohexane and previously reported data for JP-4 solutions of pentaborane. For those reaction products investigated, the blow-out velocities at a fixed equivalence ratio were higher for those materials containing higher boron concentrations; that is, blow-out velocity increased in the following order: (1) methylacetylene - diborane, (2) acetylene - diborane, and (3) ethylene - decaborane reaction products.

Report presenting testing to determine the resistance of a model of a seaplane with a length-beam ratio of 15 and a wing loading of 120 pounds per square foot was determined in smooth water and three wave heights under various conditions of load, speed, elevator setting, angle of dead rise, and center-of-gravity position.

Report presenting time histories of rolling and yawing moments on inclined bodies of revolution with vertical-tail surfaces at several Mach numbers and Reynolds numbers. Three ogival-nose bodies with three overall fineness ratios and a conical-nosed body with a fineness ratio of 12.0 were tested. Results regarding the visual-flow studies, rolling- and yawing-moment measurements, and pressure measurements are provided.

"A method is presented for calculating the aerodynamic loading, the divergence speed, and certain stability derivatives of wings and tail surfaces of arbitrary plan form and stiffness. Provision is made for using either stiffness curves and root-rotation constants or influence coefficients in the analysis. Computing forms, tables of numerical constants required in the analysis, and an illustrative example are included to facilitate calculations by means of the method" (p. 1).