Report discussing tests to determine the aerodynamic characteristics of a model of a 45 degree swept-wing fighter airplane and to determine the loads on attached stores and detached missiles. An investigation into aileron-spoiler effectiveness, aileron hinge moments, and the effects of wing modifications of aerodynamic characteristics was also carried out at various Mach numbers. Results are presented, but caution is provided in regards to extrapolating results from the model onto a full-scale aircraft.

Report presenting an investigation of the flutter characteristics of a series of thin cantilever wings with taper ratios of 0.6 for a range of Mach numbers. Results regarding flutter frequencies, time histories, effects of sweep on the flutter-speed ratio, effects of aspect ratio on the flutter-speed ratio, effects of additional models on the reference flutter speed, application of the flutter-speed ratio, and modified experimental flutter-speed coefficient are provided.

Local heat-transfer coefficients, temperature recovery factors, and pressure distributions were measured on the front side of a circular cylinder at a nominal Mach number of 3.9 over a range of free-stream Reynolds numbers from 2.1 x 10 to the 3rd power to 6.7 x 10 to the 3rd power and yaw angles from zero degrees to 44 degrees. Yawing the cylinder reduced the heat-transfer coefficients and the pressure drag coefficients. The amount of reduction may be predicted by a theory presented herein.

Report presenting an investigation to determine the damping-in-pitch characteristics of four rocket-powered wing-body combinations for a range of Mach numbers from 0.85 to 1.30. The models were tested at the same center-of-gravity location and had identical bodies. Information about the trim, lift, static longitudinal stability, dynamic longitudinal stability, and drag is provided.

Report presenting an investigation of the possibility of utilizing the relatively good characteristics of the spike-type diffuser in the supersonic compressor. Results regarding the overall performance, inlet conditions, outlet conditions, entrance flow conditions, and estimated performance of subsonic portion of rotor passage are provided.

Report presenting wind-tunnel flutter testing at a range of Mach numbers conducted on a swept-wing towed airplane model equipped with an autopilot system. Results regarding the towed model tests, fixed-root tests, and a comparison between the calculated and experimental flutter characteristics are provided.

Report of an investigation using three rocket-propelled delta-wing-body combinations for a range of Mach numbers to determine the damping-in-pitch characteristics. All models were statically stable but dynamically unstable at transonic speeds. Information about trim, lift, and drag is also provided.

Report presenting an investigation to determine the effect of ground on the low-speed aerodynamic, control, and control hinge-moment characteristics of a 3-percent-thick, delta-wing-fuselage configuration. Aerodynamic forces and moments and hinge-moment data were obtained for a range of angles of attack, ground heights, and a designated Mach and Reynolds number.

Memorandum presenting an evaluation of the performance increase resulting from the addition of 20 percent fluorine to the oxygen-RP-1 propellant combination in a 5000-pound-thrust rocket engine at a chamber pressure of 650 pounds per square inch absolute. Runs were made with the engine water cooled and regeneratively cooled.

Translating spike inlet air flow regulation characteristics from transonic to supersonic speeds at zero angle of attack.

Memorandum presenting a transonic flutter investigation of models of the all-movable horizontal tail of a fighter airplane in the transonic blowdown tunnel. The models were dynamically and elastically scaled by criteria which provide a flutter safety margin. Results regarding some general comments, simulated airplane tests, effects of pitch stiffness with rearward pitch axis, and effect of pitch-axis location are provided.

Report presenting an investigation of the low-speed static longitudinal and lateral stability characteristics of a model with an M-wing in mid and high positions and with three horizontal-tail heights. The wing had its sweep discontinuity at 40-percent wing semispan, an aspect ratio of 6, a taper ratio of 0.60, NACA 65A009 airfoil sections parallel to the plane of symmetry, and 45 degrees sweep of the quarter-chord lines. Results regarding longitudinal stability characteristics and lateral stability characteristics are provided.

A cermet composition was investigated as a potential material for gas-turbine blades. Blades of HS-21 alloy were also operated in the engine simultaneously to provide a basis of comparison. The cermet blades survived as long as approximately 312-1/2 hours at about 1500 degrees F with an average midspan centrifugal stress of approximately 11,500 psi.

"An investigation has been made in the NACA Lewis icing research tunnel to determine the aerodynamic and icing characteristics of a full-scale induction-system air-scoop assembly incorporating a flush alternate inlet. The flush inlet was located immediately downstream of the offset ram inlet and included a 180 deg reversal and a 90 deg elbow in the ducting between inlet and carburetor top deck. The model also had a preheat-air inlet" (p. 1).

From Summary: "In an effort to increase the operational range of existing small icing tunnels, the use of truncated airfoil sections has been suggested. With truncated airfoils, large-scale or even full-scale wing-icing-protection systems could be evaluated. Therefore, experimental studies were conducted in the NACA Lewis laboratory icing tunnel with an NACA 651-212 airfoil section to determine the effect of truncating the airfoil chord on velocity distribution and impingement characteristics. A 6-foot-chord airfoil was cut successively at the 50- and 30-percent-chord stations to produce the truncated airfoil sections, which were equipped with trailing-edge flaps that were used to alter the flow field about the truncated sections. The study was conducted at geometric angles of attack of 00 and 40, an airspeed of about 156 knots, and volume-median droplet sizes of 11.5 and 18.6 microns. A dye-tracer technique was used in the impingement studies."

"An NACA 65(sub 1)-212 airfoil of 8-foot chord was provided with a gas-heated leading edge for investigations of cyclical de-icing. De-icing was accomplished with intermittent heating of airfoil segments that supplied hot gas to chordwise passages in a double-skin construction. Ice removal was facilitated by a spanwise leading-edge parting strip which was continuously heated from the gas-supply duct. Preliminary results demonstrate that satisfactory cyclical ice removal occurs with ratios of cycle time to heat-on period (cycle ratio) from 10 to 26" (p. 1).

From Summary: "A procedure is presented for determining boundary-layer quantities from pressure-rake data, which include the combined effects of viscous and shock losses. The problem is analyzed using schileren photographs of the shock configuration, the continuity of mass relationship, and the characteristics of the turbulent boundary layer that its outer edge is defined by a rapid change in slope in the Mach-number profiles in the vicinity of the edge."

From Summary: "Sound pressure levels, frequency spectrum, and jet velocity profiles are presented for an engine-afterburner combination at various values of afterburner fuel - air ratio. At the high fuel-air ratios, severe low-frequency resonance was encountered which represented more than half the total energy in the sound spectrum. At similar thrust conditions, lower sound pressure levels were obtained from a current fighter air craft with a different afterburner configuration. The lower sound pressure levels are attributed to resonance-free afterburner operation and thereby indicate the importance of acoustic considerations in afterburner design."

Memorandum presenting the effect of missile armament on the performance of an interceptor-type aircraft model at Mach numbers 1.5, 1.7, and 1.9 and at angles of attack up to 19 degrees. The aircraft model was characterized by triangular-shaped normal-shock inlets located at wing roots. Results regarding force measurements, effect of armament on inlet-duct performance, fuselage boundary-layer survey, and total-pressure contours at inlet throat and diffuser exit are provided.

Memorandum presenting a technique for predicting the influence of body vortices and the wing shock-expansion field on the pitch-up characteristics of supersonic airplanes to supplement the calculative methods for wing vortices which are well known. The method is applied to the prediction of the pitch-up characteristics of four airplanes with high tails, of which one serves as a calculative example.

Memorandum presenting static longitudinal stability and control characteristics of a flare-stabilized body of revolution employing a movable portion of the flare surface as a pitch control determined for a range of Mach numbers, angles of attack, and control deflections. The variation of lift coefficient with pitching-moment coefficient for the basic configuration with control undeflected was found to be essentially linear, and the stability to increase slightly with increasing Mach number.

Combustion efficiency of pentaborane fuel in 48- inch diameter ramjet engine.

Report presenting an investigation to determine separately the aerodynamic characteristics of a Douglas Aircraft Company store and a semispan delta-wing-fuselage configuration in the presence of one another. The store was located at the 50-percent-semispan station with the store nose both ahead of and behind the wing leading edge for two longitudinal and three vertical positions.

Memorandum presenting a performance investigation using hydrogen fuel in a full-scale afterburner conducted with particular study of fuel-injector configurations and afterburner length. A total of seven fuel-injector configurations, grouped by type as concentric ring or radial bar, were investigated at a specified burner-inlet velocity and range of burner-inlet total pressures.