Report presenting the results of flight investigations showing that a beveled trailing-edge aileron gives as low or a lower profile drag than a contour aileron. Section profile drag and lift coefficients with two different types of ailerons were obtained at 3 different Reynolds numbers.

Wing pressure distribution diagrams for several angles of attack and flap deflections of 0 degrees, 20 degrees, and 40 degrees are presented. The normal force coefficients agree with lift coefficients obtained in previous test of the same model, except for the maximum lifts with flap deflection. Pressure distribution measurements were made at Reynolds Number of about 6,000,000.

Report presenting pressure distribution measurements on two 24-inch chord models equipped with Fowler flaps in the two-dimensional low-turbulence pressure tunnel. Results regarding pressure-distribution diagrams and normal-force and moment coefficients are provided.

"The knock-limited performance of blends of 0,50; and 100 percent by volume of 2,2,3-trimethylpentane in 28-R fuel determined with a modified F-4 engine at three sets of conditions varying from severe to mild at each of three compression ratios (6.0, 8.0, and 10.0). A comparison of the knock-limited performance of 2,2,3-trimethylpentane with that of triptane (2,2,3-trimethylbutane) is included. The knock-Limited performance of 2,2,3-trimethylpontane was usually more sensitive to either compression ratio or inlet-air temperature than 28-R fuel, but the ratio of the knock-limited indicated mean effective pressure of a given blend containing 2,2,3-trimethypentane and 28-R to the indicated mean effective pressure of 28-R alone was not greatly affected by compression ratio if the engine operating conditions were mild" (p. 1).

Report presenting tests of airplane models that included investigations to determine the longitudinal stability and control, effects of various constituent parts or their modification on longitudinal stability and control, critical speed, and distribution of wing load. Some of the changes made in attempts to improve longitudinal control and to increase critical speed included auxiliary control flaps on the lower surface of the wing, revision of the windshield, increase in dimensions of outboard nacelles, and alteration in profile of wing leading edge.

Report presenting tests made in order to determine the differences in high-speed aerodynamic characteristics between models of a four-engine transport airplane and a similar bomber airplane. The main conclusion found is that the critical Mach number of the transport model is about 0.05 less than that of the bomber model.

Report providing charts to assist with estimating F-3 and F-4 knock-limited performance ratings for several ternary and quaternary fuel blends. Several unusual behaviors were noted in the F-3 engines using the aromatic-paraffinic blends, so the charts for them may not be as accurate. General trends observed in different types of fuel are also described.

Report presenting power-off wind tunnel tests of a scale model of a twin-engine cargo airplane equipped with amphibious floats. Longitudinal and lateral stability and control characteristics were investigated for three flap positions.

Report presenting testing in the full-scale tunnel to provide data for estimating the longitudinal stability and control characteristics of the Curtis XP-55 airplane. Testing included lift, drag, pitching-moment, hinge-moment, and elevator pressure measurements for various combinations of angle of attack, elevator deflection, and elevator tab settings. The results of the force tests and some correlation of the results of the force tests and the pressure measurements are presented in the report.

Report discussing an investigation into several types and sizes of flaps and spoilers located forward of the elevators on the upper surface of the horizontal stabilizer of a model of a radial-engine pursuit airplane. Information about the elevator characteristics, elevator-fixed and elevator-free balance lift coefficient, and trim drag coefficient for a range of Mach numbers is provided.

Report presenting testing in the two-dimensional low-turbulence pressure tunnel and the two-dimensional low-turbulence tunnel of two models made by the Consolidated Aircraft Corporation, one of the outboard section and one of the inboard section.

Supplement using data from a previous report to show the cargo that can be carried at various ranges, pounds of cargo that can be carried per pound of fuel, and other graphs to simplify the problem of determining which cargo can be carried at any range. The assumptions, parameters, and equations from the original report are carried over in the supplement.

Report discussing tests of the drag clean-up and stability of the Bell YP-59A jet-propelled airplane. The general stability, static stability, and control characteristics were examined. Specific details are also included about the effects of the exhaust jet on air flow at the tail.

Report presenting tests of the Northrop MX-334 airplane in the full-scale tunnel. The results are of particular interest since the MX-334 is an all-wing glider-type airplane without a conventional fuselage or vertical surfaces. The primary purpose was to obtain sufficient data with which to determine the longitudinal and lateral stability and control characteristics of the airplane.

Report discusses a method of correlating engine-cooling data and its application to a representative engine-cooling test. Considerations for the correlation method are given, but the application to specific engine-cooling problems should be simple and direct. Information about experimental procedure and an example with specific values are included.

Report presenting an investigation in the two-dimensional low-turbulence tunnels for the purpose of developing an optimum flap configuration for maximum lift on an airfoil section for the Republic XF-12 airplane equipped with a double slotted flap. Lift and flap loads were obtained at several flap deflections for two flap paths. Results regarding lift, drag, and flap loads are provided.

Report presenting tests of representative models of flying boat hulls to determine the resistance at low speeds. Results regarding the effect of load coefficients, resistance coefficients, and towing and drifting calculations are provided.

"In order to eliminate the formation of ice on the carburetor throttle plates of an aircraft-engine induction system, two modifications of the throttle design and a variation in the method of throttle operation of the twin-barrel injection carburetor were tested" (p. 1). The modifications were investigated under severe icing conditions at normal power, maximum cruising power, and 60-percent normal power. The only modification that appeared to provide deicing assistance were the electrically heated throttle plates.

Report discussing testing on two types of single cylinders to determine the effect of the relation of exhaust pressure to inlet-air pressure on knock-limited performance. Variables explored included exhaust pressure, fuel-air ratio, and engine speed. Three types of fuels were also used to explore the effect of exhaust pressure on fuel ratings.

"Flight measurements have been made of the individual aileron hinge moments, aileron rolling effectiveness pb/2V ,and stick-force characteristics in abrupt aileron rolls with a P-40F airplane (AAF No. 41-14119) over an indicated airspeed range from 108 to 304 miles per hour. Three methods for measuring the rate of change of hinge moment with angle of attack were investigated. Presented for comparison with the flight results are data from two-dimensional wind-tunnel tests of the wing-aileron profile as measured at the center aileron hinge" (p. 1).

Report presenting testing to determine the best way to land the SB2C-1 airplane in calm and rough water and to determine its probable ditching performance. The behavior of the model was determined by making visual observations and by recording the maximum longitudinal decelerations and by taking motion pictures of the ditchings. Results regarding the effect of flaps, attitude, weight, a wing-low landing, effect of simulated damage, effect of tail wheel, ditching aids, and seaway are provided.

Behaviors of both model and full-scale airplanes were ascertained by making visual observations, by recording time histories of decelerations, and by taking motion picture records of ditchings. Results are presented in form of sequence photographs and time-history curves for attitudes, vertical and horizontal displacements, and longitudinal decelerations. Time-history curves for attitudes and horizontal and vertical displacements for model and full-scale tests were in agreement; maximum longitudinal decelerations for both ditchings did not occur at same part of run; full-scale maximum deceleration was 50 percent greater.

Report discussing a series of single-cylinder engine tests to determine the effect of special surface coatings in porous chrome-plated cylinder barrels on oil consumption and ring wear. The coating materials were selected for their bearing and lubrication properties and on their applicability to processing. The surface coatings tested were lead overplates, silver overplates, and colloidal graphite base paint.

Report presenting a series of single-cylinder engine tests run to determine a satisfactory method of reducing oil consumption in radial air-cooled engines with flat-face compression rings as standard parts and equipped with cylinder barrels salvaged by porous chrome plating. Testing was conducted using porous chrome-plated cylinders with straight and choke bores with standard flat-face compression rings.