Report describing methods of determining trace impurities in plutonium in connection with the Metal Fabrication Process. The methods included are the cupferron extraction-copper spark method and the direct copper spark method.

Facilities are to be designed for installation at Hanford for the reprocessing of irradiated, low enrichment fuels from non-production reactors, see Reference 1 and 2. The initial design of the processing facilities is to be based on processing the fuels discharged from the Dresden, Yankee, Piqua, Pathfinder and Shippingport (blanket elements only) reactors. Properties of the fuels and cladding make it impossible to completely process them in existing equipment, although the separation and decontamination can be performed in existing facilities once the fueks have been placed in solution form.

Disposal on a specific retention basic of certain radioactive liquid waste solutions emanating from separations from separations plants has been practiced at Hanford since 1944. As used at Hanford, the term "specific retention" is defined as that volume of waste liquids that may be disposed to the soil* and be held against the force of gravity by the molecular attraction between sand grains and the surface tension of the water, when expressed as percent of packed soil volume. In practice it represents the volume of liquid that may be discharged to a disposal pit of known dimensions without leakage to the ground, water, expressed as percent of the total volume of a column of soil with the same cross section as the pit, and extending from the bottom of the pit to the water table. It is recognized that some degree of lateral spreading will occur which has the effect of enlarging the volume of soil contacted by the liquid.

Report discussing the dissolution of simulated fuel cores. Equipment and procedures are discussed along with significant characteristics of the core materials.

The preceding report follows an extensive study made at Hanford of methods and equipment to remove effectively the dissolver vent gases.

From introduction: "Five appendices, each of which pertains to a separate phase of the Filtration of Radioactive Aerosols by Glass Fibers program."

The investigation to be described in this paper was one of several undertaken to resolve a curious discrepancy that had arisen in measurements of the diffusion length of graphite. Those diffusion lengths measured with the graphite layups of 100 Area piles were three to six centimeters higher than the value obtained with the Hanford Standard Pile. The fact that the 100 Area structures of the order of 40 ft. X 40 ft. X 30 ft, not including reflector, approximated an infinite medium, whereas sigma piles are of the order of 8 ft. X 8ft. X 10 ft., suggested the possibility that the diffusion length obtained by mensuration of relative fluxes and application of the conventional equations depended in some way on the size of the medium. Therefore, in order to determine if such a dependency actually exists, it was proposed to erect a series of graphite stacks of different dimensions and to make diffusion length measurements in each.

In answer to the question, "How well do we know the composition of the fuel material for the PRTR start-up tests?", the analytical data on the PRTR fuel elements and other fuel elements which were fabricated by similar processes was gathered and analyzed. The results of this analysis are presented.

This report is a document summarizing all information available on life aspects of various measures proposed to reduce or eliminate corrosion of Van Stone flanger.

The feasibility of removing and recovering cesium-137 from various HAPO process solutions by precipitation of Cs2ZnFe(CN)6 has been demonstrated previously. Pilot plant studies of calcination and steam hydrolysis of non-radioactive Cs2ZnFe(CN)6 precipitates by members of the Process Equipment Development Operation are currently in progress. In support of these pilot plant studies, experiments were performed to determine the extent, if any, to which cesium volatilizes during calcination and hydrolysis of Cs2ZnFe(CN)6 precipitates containing cesium-137. Experimental procedures and results are presented in this report.

Investigation of aqueous and steam corrosion at elevated temperature has been carried on at Hanford for several tears. A number of reports have been published on various phases of the corrosion program but, except for monthly reports, little has been written on the progress of the Corrosion and Coatings Operation alloy development program. This interim report will outline the more important current phases of the aluminum alloy program.

The preparation of radioactive metallurgical specimens for microscopic examination is one of the responsibilities of the Radiometallurgy Sub-Unit. An abrasive cut-off machine development program, based upon a previous experimental model, was undertaken to provide a method for sectioning of irradiated materials without undue personnel exposure or spread of contamination and finally to provide data for the design of an abrasive cutting unit for use in the work cells in the Radiometallurgy Building. A horizontal-feed type set-off machine, powered by a 7 1/2 hp motor with V-belt drive, has been developed for the submerged sectioning of irradiated uranium and is currently being used successfully to obtain samples for metallurgical, chemical and physical investigations without excessive personnel exposure or spread of radioactive contaminates.

In obtaining the results reported here a double focusing magnetic type spectrometer was used. Momentum spread was about 1%, and in most cases 2560 counts per point were taken. An end window Geiger tube was used as a detector. The window was of mica with areal density of 1.6 mg/cm2.

Report summarizing data from Purex tests for pulse column specifications. These test results were used to estimate pilot plant specifications.

The wrist badge provides a dosimeter that is useful in estimating the radiation dose to the hands and forearms. Its new shield system gives good gamma and slow neutron dose discrimination with duPont 552 film packets. The film can be evaluated using the present technique and equipment. Several attempts to develop hand dosimeters have been made. Finger rings using film have been used routinely but have not been entirely satisfactory for all situations. The wrist badge was developed to provide improved gamma and slow neutron dose measurement of the upper extremities under certain appropriate conditions. The wrist badge dosimeter is not a substitute or alternate for finger ring dosimeters but is a necessary dosimeter for some extremity exposure situations.

The following report discusses laboratory investigations of the suitability of some commercially available limestone for neutralization of slightly acidic distillates.

Report reviewing a study regarding the chemical properties, appearance, texture, homogeneity and slurrying ability of waste metal sludge. The settling rates of sludge-supernatant slurries is also discussed.

Laboratory studies have shown that the double salt, CaF2-PuF4, can be precipitated by rapid addition of hydro-fluoric acid to solutions containing 25 to 75 g Pu/1, caleium equimolar to plutonium, and 1 to 10 M HNO3. The precipitate, which is subsequently washed with water and dried to 300 degrees C in dehumidified, deoxygenated argon, can be reduced thermally by calcium to give high yields of plutonium metal.

Graphs for estimation of plutonium and trans-plutonium isotopic content of irradiated plutonium reactor fuel of various initial isotopic compositions.

The measurement of a alpha-particle energy has been used by many radiochemical laboratories for the identification and analysis of alpha-active radio nuclides. The use of the total-ionization method for alpha-active radio-nuclides. The use of the total-ionization method for alpha energy in ionization chamber in which the alpha particle loses all its energy in ionization of the chamber gas. Collection of the electrons thus formed generates a voltage pulse across the chamber capacity which is proportional to the alpha particle energy. This pulse is then amplified using a suitable linear amplifier and fed to a pulses as to amplitude; the information is then recorded or stored. Since the pulse amplitude is proportional to the alpha energy lost to the chamber gas, the pulse height analysis can be used to estimate the energy of the alpha particles and in the case of several alpha emitters of different energies, the relative abundance of the alpha emitters can be determined. An alpha energy analyzer system using the ion collection method has been fabricated for use in radiochemical laboratories required to perform a large number of alpha energy determinations. This report describes the operation, maintenance, and application of this alpha energy analyzer system.

Several improvements have been made in the gamma scintillation counter (GSC). The Model V gamma scintillation counter uses a canned thallium activated sodium iodide crystal as a detector. Although the electronic components remain unchanged, a modification of the sample support has been made to improve reproducibility of geometry. To assure comparable results between various counters, they must be operated at the same energy threshold and counting yield. Methods have been developed to assure operation at a preferred energy threshold of 0.1 Mev and an arbitrarily fixed counting yield of 3.36% for Cs-Ba-137. Partial pulse height discrimination against U 237 is also accomplished.

Judging scratch depth or surface roughness by unaided visual inspection under controlled conditions, while rapid and popular, is not quantitative. Comparison methods improve reproducibility but are generally not applicable to evaluation of depths of single widely spaced scratches. Stylus-type contour recorders yield valuable scratch contour data but may themselves plow through soft materials and fine details. Depth measuring microscopes are particularly applicable to measurement of pinhole depth but do not graphically reveal profiles and provide only a small field of view. The comparatively large field of view and graphic display of contour provided by profile microscopes make them particularly suitable for evaluation scratch depth as well as surface roughness. A HAPO-constructed instrument has demonstrated an accuracy of +/- 50 micro inches in the range of 50 to 15,000 micro-inches scratch depth. It is a pocket-sized, portable, and can be used on horizontal and vertical surfaces by untrained persons with only brief instruction.

Summary: A method was found for determining calcium concentrations in TBP process streams in spite of serious interferences bysodium, ferrous, uranyl, sulfate, phosphate, and sulfamate ions as well as by TBP. The precision attainable varied from sample to sample, depending upon its composition. In general, errors of 20% or greater occurred. The smallest determinable amount of calcium was about 10 mg/1.

Abstract: "A method has been established for the estimation of volatile organic acids in aqueous process solutions containing UNH, nitric acid, ANN, sodium dichromate and small amounts of hexone. The practice is to distill a 400 ul or 500 ul sample in the presence of an excess of phosphoric acid and ferrous sulfate under a high vacuum; a special apparatus utilizing a receiver cooled with a dry ice-isopropanol mixture is employed. The distillate is taken up in isopropanol and then titrated potentiometrically with standard potassium hydroxide solution. Since nitric acid and organic acids are present, two end points are observed. The potassium hydroxide added between these end points is equivalent to the organic acids. In the titration, CO2 from the atmosphere or in the potassium hydroxide is a source of error. The former was avoided and correction was made for the latter."