It was a worthwhile task to research methods to lower the cooling drag of radiators. And the success of these efforts has been so great that without this research the modern high-speed airplane would have decidedly inferior performance. It is the purpose of this report to give a comprehensive discussion of all the fundamental principles and phenomena that offer a key to understanding modern cooling problems.

The downwash velocity distribution behind the wing was determined for the free jet and for the closed tunnel of both circular and elliptic cross sections. The wing was placed at the center of the tunnel. The theory makes it possible to determine the downwash at any point in the jet. The computations were performed for points in the plane determined by the jet axis and the center-of-pressure line of the wing.

It is sufficient to consider only the equations of motion of the towed body whereas those of the cable may be left out of consideration. The result obtained makes it possible to determine which factors affect the critical velocity and what modifications of the instrument are necessary for extending the upper limit of that velocity.

This report deals first with the fundamental data required for the investigation. These are chiefly the aerodynamic forces and moments acting on an airplane in a flat spin. It is shown that these forces and moments depend principally on the angle of attack and on the rotation about the path axis, and can therefore either be measured in a wind tunnel or calculated from wind-tunnel measurements of lift, drag and moment about the leading edge of the wing of an airplane model at rest.

Describes procedures and equipment used for dehorning, castrating, branding, and marking beef cattle. Explains the use of these procedures as means for loss prevention in the beef industry.

The 6.C.1 balance is the first fully automatic balance assuring a continuous and simultaneous record of the aerodynamic characteristics of an airfoil in a wind tunnel. Because of the rapidity of the measurements a complete polar (six components) requires only about three minutes of wind, that is to say, of motive power, which is of interest for wind tunnels with high efficiency factors and may lead to the economical design of large size wind tunnels.

"Equations and design charts are given for predicting the downwash angles and the wake characteristics for power-off conditions behind plain and flapped wings of the types used in modern design practice. The downwash charts cover the cases of elliptical wings and wings of taper ratios 1, 2, 3, and 5, with aspect ratios of 6, 9, and 12, having flaps covering 0, 40, 70, and 100 percent of the span. Curves of the span load distributions for all these cases are included" (p. 1).

This paper restricts itself to radial impellers with cylindrical blades since, as Prasil has shown, the flow about an arbitrarily curved surface of revolution may be reduced to this normal form we have chosen by a relatively simple conformal transformation. This method starts from the simple hypotheses of the older centrifugal impeller theory by first assuming an impeller with an infinite number of blades. How the flow is then modified is then investigated.

Load factors and loading conditions are presented for German aircraft. Loading conditions under various stress factors are presented along with a breakdown of individual aircraft components such as landing gear, wings, etc.

Load factors and loading conditions are presented for Germany, England, and the United States. Results of tests are presented and loading conditions are presented under various stress categories like freight, commercial, aerobatics, and training.

Describes the various types of disease which fur animals may contract, and provides suggestions for preventing or controlling these diseases.

"NACA model 11-C was tested with four different depths of step to obtain information as to the effect of the depth of step on the water performance. The depths of step were selected to cover the practicable range of depths and in each case the included angle between the forebody and afterbody keels was kept the same 6-1/2 degrees. Small depths of step were found to give lower resistance at speeds below and at the hump speed of the model and greater depths of step lower resistance at high speeds" (p. 1).

"The effect of various injection-valve opening pressures on the spray-tip penetration was determined for several injection pressure. A common-rail fuel injection system was used. For a given injection pressure a maximum rate of penetration was obtained with an injection-valve opening pressure equal to the injection pressure" (p. 1).

"Tests have been made in the NACA 7 by 10 foot wind tunnel on a Clark Y wing model equipped with various lengths of Handley Page slots extending inward from the wing tips. The slot lengths tested ranged from 20 to 100 per cent of the semi span. The effect of slot lengths on damping in roll was determined by means of both free-autorotation and forced-rotation test. In addition, the maximum lift coefficient was found with each slot length. The optimum length of slot for satisfactory damping in roll over a large range of angles of attack was found to be slightly over 50 per cent of the semispan for the form of slot tested" (p. 1).

"In this report are presented the results of wind-tunnel tests of retractable spoilers on the upper surface of a Clark Y wing, which have been made as part of an investigation of lateral control devices being conducted by the National Advisory Committee for Aeronautics. Spoilers with chords up to 15.0 percent of the wing chord were tested in several locations on a plain rectangular wing and in two locations on the same wing equipped with a 20.0 percent chord split flap down 60 degrees. Charts are given for four representative angles of attack from which values of rolling- and yawing-moment coefficients may be obtained for spoilers up to 15.0 percent chord located on the upper surface of a Clark Y wing" (p. 1).

In the present report, aerodynamic relations under the effect of the weight moments are investigated, and an example given of the computation of the stability for a practical case. Later, the effects of the masses of the controls on the dynamic longitudinal stability will be considered.

An investigation was made in the N.A.C.A. 7- by 10-foot wind tunnel to determine the aerodynamic characteristics of tapered and rectangular wings with partial-span slotted flaps. Two N.A.C.A. 23012 airfoils equipped with center-section and tip-section flaps were tested. The results showed that the changes in lift and drag due to changes in flap span for both rectangular and tapered wings having partial-span slotted flaps were similar to those for corresponding wings having partial-span split or plain flaps. For the two wings tested, higher values of maximum lift were obtained with center-section slotted flaps than with tip-section slotted flaps of the same size. The highest values of lift-drag ratio at maximum lift for the rectangular wing were obtained with center-section flaps and, for the tapered wing, with tip-section flaps. Center-section flaps on the tapered wing gave higher values of drag at maximum lift than tip-section flaps; no great difference in drag at maximum lift was apparent for either center-section or tip-section slotted flaps on the rectangular wing.

From Summary: "This report presents the results of an investigation to determine the engine performance obtained with a hydrogenated safety fuel developed to eliminate fire hazard. The tests were made on a single-cylinder universal test engine at compression ratios of 5.0, 5.5, and 6.0. Most of the tests were made with a fuel-injection system, although one set of runs was made with a carburetor when using gasoline to establish comparative performance. The tests show that the b.m.e.p. obtained with safety fuel when using a fuel-injection system is slightly higher than that obtained with gasoline when using a carburetor, although the fuel consumption with safety fuel is higher."

"A method of determining the moments of inertia of an airplane from design data pertaining to the weights and locations of the component parts is described. The computations required to ascertain the center-of-gravity position are incorporated with the calculations of moments of inertia. A complete set of data and calculations for a modern airplane is given to illustrate the procedure. From a comparison between calculated values and measured values it is believed that the moments of inertia can be estimated within 10 percent by the use of this method" (p. 1).

Note presenting a method of estimating the variation of thrust horsepower with air speed, when the power unit consists of a conventional, thin, metal, fixed-pitch propeller driven by an internal-combustion engine. Such a curve is needed for the estimation of airplane performance in conjunction with a curve of horsepower required for maintaining level flight.

Report issued by the U.S. Bureau of Mines on studies of the known natural gas reserves in central Michigan sandstone deposits. The geology and methods used to estimate the reserves are presented. This report includes tables, illustrations, and maps.

Circular presenting a description of the Farman night bombers 211 and 212, which are four-engine high-wing monoplanes that are equipped with different engines. Details of the wing structure, fuselage, tail surface and controls, landing gear, power plant, characteristics, performance, drawings, and photographs are provided.

The following discussion is at first restricted to the light-oil engines now in use. We shall consider how far it is possible to reduce fire hazards by changes in the design of the engines and carburetors and in the arrangement of the fuel pipes.

The dynamic longitudinal stability characteristics of eight airplanes as defined by the period and damping of the longitudinal oscillations were measured in flight to determine the degree of stability that may be expected in conventional airplanes. An attempt was made to correlate the measured stability with pilots' opinions of the general handling characteristics of the airplanes in order to obtain an indication of the most desirable degree of dynamic stability. The results of the measurements show that the period of oscillation increases with speed. At low speeds a range of periods from 11 to 23 seconds was recorded for the different airplanes. At high speeds the periods ranged from 23 to 64 seconds. The damping showed no definite trend with speed.