Serial/Series Title
1,100 Matching Results
Results open in a new window/tab.
Results:
1 - 24 of
1,100
next
Abacus for the Reduction of English Measures to the Metric System and Vice Versa
This report presents a description of an abacus with three scales: one for English measures, one for metric measures, and one with the "points of reduction", as well as construction details. There is also a detailed description on how to use the abacus.
Date:
July 1921
Creator:
Tenani, Mario
System:
The UNT Digital Library
Abstracts Pertaining to Seaplanes
Report discussing about 400 references pertaining to the hydrodynamic design of seaplanes have been compiled, and the information is presented in the form of abstracts classified under six main headings.
Date:
July 24, 1947
Creator:
Bidwell, Jerold M. & King, Douglas A.
System:
The UNT Digital Library
Acceleration Characteristics of a Turbojet Engine With Variable-Position Inlet Guide Vanes
Report presenting a study of the acceleration characteristics of a turbojet engine equipped with variable-position inlet guide vanes in the altitude test chamber. Maximum acceleration values for 3 engines of the same model were also obtained during testing and were found to differ as much as 50 percent. Results regarding the effect of fuel step size and inlet guide vane on acceleration, effect of flight condition, reproducibility of engine acceleration, compressor pressure ratio in relation to acceleration, and acceleration with inlet air distortion are provided.
Date:
July 7, 1955
Creator:
Dobson, W. F. & Wallner, Lewis E.
System:
The UNT Digital Library
Acceleration of high-pressure-ratio single-spool turbojet engine as determined from component performance characteristics 2: effect of compressor interstage air bleed
Report presenting an analytical investigation to determine the effect of compressor interstage air bleed with the use of constant-area bleed ports on the acceleration characteristics of a typical high-pressure-ratio single-spool turbojet engine. Constant-area interstage bleed, properly located, gave smaller acceleration times than variable-area compressor exit bleed. Results regarding acceleration with interstage bleed, acceleration using constant-area interstage bleed in combination with compressor outlet bleed, variable-area interstage bleed, and comparison of acceleration modes are provided.
Date:
July 3, 1953
Creator:
Rebeske, John J., Jr. & Dugan, James F., Jr.
System:
The UNT Digital Library
Additional measurements of the low-speed static stability of a configuration employing three triangular wing panels and a body of equal length
From Introduction: "The results of an investigation of the low-speed static stability of a simplified model of such an arrangement having one of the airfoils placed vertically on top of the body and the other two as wing panels having negative dihedral are presented in reference 1. In order to provide information for predicting the effects of changes in the basic configuration on the low-speed stability characteristics presented in reference 1, additional measurements have been made."
Date:
July 25, 1955
Creator:
Delany, Noel K.
System:
The UNT Digital Library
Additional Static and Fatigue Tests of High-Strength Aluminum-Alloy Bolted Joints
From Introduction: "Early in 1951 the National Advisory Committee for Aeronautics published, as Technical Note 2276 (ref. 1), a report by the Aluminum Research Laboratories of the Aluminum Company of America on the results of static and fatigue tests of high-strength aluminum alloy monobloc specimens and bolted joints. In view of special interest shown by several aircraft companies, certain expansions of the test program were undertaken by the Aluminum Research Laboratories and are reported herein."
Date:
July 1954
Creator:
Hartmann, E. C.; Holt, Marshall & Eaton, I. D.
System:
The UNT Digital Library
Aerial navigation by dead reckoning
Report discussing the problem to be solved, as presented to the pilot or observer of an aircraft, is as follows: The aircraft starting from A must land at B, the only data being the speed of the airplane, the altitude and the orientation D of the course. The above data would be amply sufficient, were it not for the fact that the airplane is constantly subjected to a wind of variable direction and strength.
Date:
July 1922
Creator:
Maffert, Pierre
System:
The UNT Digital Library
Aero Dopes and Varnishes
Report discussing before proceeding to discuss the preparation of dope solutions, it will be necessary to consider some of the essential properties which should be possessed of a dope film, deposited in and on the surface of an aero fabric. The first is that it should tighten the material and second it should withstand weathering.
Date:
July 1927
Creator:
Britton, H. T. S.
System:
The UNT Digital Library
Aerodynamic Characteristics at High and Low Subsonic Mach Numbers of the NACA 0012, 64₂-015, and 64₃-018 Airfoil Sections at Angles of Attack from -2 Degrees to 30 Degrees
An investigation has been made in the Langley low-turbulence pressure tunnel of the aerodynamic characteristics of the NACA 0012, 64(sub 2)-015, and 64(sub 3)-018 airfoil sections. Data were obtained at Mach numbers from 0.3 to that for tunnel choke, at angles of attack from -2deg to 30deg, and with the surface. of each airfoil smooth-and with roughness applied at the leading edge.The Reynolds numbers of the tests ranged from 0.8 x 10(exp 6) to 4.4 x 10(exp 6). The results are presented as variations of lift, drag, and quarter-chord pitching-moment coefficients with Mach number.
Date:
July 23, 1954
Creator:
Critzos, Chris C.
System:
The UNT Digital Library
Aerodynamic Characteristics at Supersonic Speeds of a Series of Wing-Body Combinations Having Cambered Wings With an Aspect Ratio of 3.5 and a Taper Ratio of 0.2: Effect at M = 2.01 of Nacelle Shape and Position on the Aerodynamic Characteristics in Pitch of Two Wing-Body Combinations with 47 Degree Sweptback Wings
Memorandum presenting an investigation at M = 2.01 in the 4- by 4-foot supersonic pressure tunnel to determine the effect of a series of nacelles on the longitudinal stability characteristics of a sweptback wing-body combination. Nacelle shape and position were varied on a configuration with a 6-percent-thick wing with an aspect ratio of 3.5, a taper ratio of 0.2, and 47 degrees of sweep at the quarter chord.
Date:
July 25, 1952
Creator:
Driver, Cornelius
System:
The UNT Digital Library
The aerodynamic characteristics at transonic speeds of an all-movable, tapered, 45 degrees sweptback, aspect-ratio-4 tail surface deflected about a skewed hinge axis
From Introduction: "The purpose of the present paper was to determine whether the characteristics about a skewed axis could be predicted from data about the normal angle-of-attack axis, and whether such a configuration offered any aerodynamic advantages over the conventional hinge location normal to the pane of symmetry."
Date:
July 3, 1952
Creator:
Hammond, Alexander D. & Watson, James M.
System:
The UNT Digital Library
Aerodynamic Characteristics of a 1/4-Scale Model of the Duct System for the General Electric P-1 Nuclear Powerplant for Aircraft
Report discussing testing on a model of the General Electric P-1 nuclear powerplant to determine its internal aerodynamic characteristics. The main purposes of testing were to measure the mass-flow distribution of air, to measure the total-pressure losses for the duct components and complete model, and to determine modifications necessary to attain the desired performance characteristics.
Date:
July 29, 1955
Creator:
Wood, Charles C. & Henry, John R.
System:
The UNT Digital Library
Aerodynamic Characteristics of a 4-Engine Monoplane Showing Comparison of Air-Cooled and Liquid-Cooled Engine Installations
From Introduction: "An investigation has been conducted in the N.A.C.A. full-scale wind tunnel to determine the aerodynamic characteristics of a 1/4-scale model of a 4-engine monoplane when equipped with comparable air-cooled engine and liquid-cooled engine installations. The air-cooled engine installation consisted of nacelles equipped with N..A.C.A. cowlings and oil coolers located in the leading edge of the wing."
Date:
July 1939
Creator:
Silverstein, Abe & Wilson, Herbert A., Jr.
System:
The UNT Digital Library
The aerodynamic characteristics of a body in the two-dimensional flow field of a circular-arc wing at a Mach number of 2.01
From Introduction: "The present report is concerned with the characteristics of a body in the two-dimensional flow field of a circular-arc wing of rectangular plan form."
Date:
July 2, 1957
Creator:
Gapcynski, John P. & Carlson, Harry W.
System:
The UNT Digital Library
Aerodynamic characteristics of a wing with quarter-chord line swept back 45 degrees, aspect ratio 6, taper ratio 0.6, and NACA 65A009 airfoil section
From Introduction: "This paper presents the results of the investigation of the wing-alone and wing-fuselage configurations employing a wing with the quarter-chord line swept back 45^o, aspect ratio 4, taper ratio 0.3, and an NACA 65A006 airfoil section parallel to the stream."
Date:
July 20, 1949
Creator:
Spreemann, Kenneth P.; Morrison, William D., Jr. & Pasteur, Thomas B., Jr.
System:
The UNT Digital Library
Aerodynamic characteristics of NACA RM-10 missile in 8- by 6-foot supersonic wind tunnel at Mach numbers from 1.49 to 1.98 1: presentation and analysis of pressure measurements (stabilizing fins removed)
Experimental investigation of flow about a slender body of revolution (NACA RM-10 missile) aligned and inclined to a supersonic stream was conducted at Mach numbers from 1.49 to 1.98 at a Reynolds number of approximately 30,000,000. Boundary-layer measurements at zero angle of attack are correlated with subsonic formulations for predicting boundary-layer thickness and profile. Comparison of pressure coefficients predicted by theory with experimental values showed close agreement at zero angle of attack and angle of attack except over the aft leeward side of body. At angle of attack, pitot pressure measurements in plane of model base indicated a pair of symmetrically disposed vortices on leeward side of body.
Date:
July 20, 1950
Creator:
Luidens, Roger W. & Simon, Paul C.
System:
The UNT Digital Library
Aerodynamic characteristics of NACA RM-10 missile in 8- by 6-foot supersonic wind tunnel at Mach numbers from 1.49 to 1.98 2: presentation and analysis of force measurements
Experimental investigation of aerodynamic forces acting on body of revolution (NACA RM-10 missile) with and without stabilizing fins was conducted at Mach numbers from 1.49 to 1.98 at angles of attack from 0 to 9 degrees and at Reynolds number of approximately 30,000,000. Comparison of experimental lift, drag, and pitching-moment coefficients and center of pressure location for body alone is made with linearized potential theory and a semiempirical method. Results indicate that aerodynamic characteristics were predicted more accurately by semiempirical method than by potential theory. Breakdown of measured drag coefficients into components of friction, pressure, and base-pressure drag is presented for body alone at zero angle of attack.
Date:
July 21, 1950
Creator:
Esenwein, Fred T.; Obery, Leonard J. & Schueller, Carl F.
System:
The UNT Digital Library
Aerodynamic Characteristics of Several Modifications of a 0.45-Scale Model of the Vertical Tail of the Curtiss XP-62 Airplane
"In the course of an investigation to find a satisfactory vertical tail for the XP-62 airplane, a 0.45-scale vertical tail model on a stub fuselage was tested in the Langley 7- by 10-foot tunnel. This model was fitted with a flat plate to represent the horizontal tail surface. The data are presented herein for their general interest value rather than their application to this particular airplane" (p. 1).
Date:
July 1946
Creator:
Lowry, John G.; Turner, Thomas R. & Liddell, Robert B.
System:
The UNT Digital Library
Aerodynamic characteristics of two 25-percent-area trailing-edge flaps on an aspect ratio 2 triangular wing at subsonic and supersonic speeds
Report presenting the results of an investigation of flap-type controls on a low-aspect-ratio triangular wing using NACA 0005-63 sections for a constant-chord and a constant-percent-chord control surface. Two flap profiles were investigated: one with a true contour and the other with a blunt trailing edge. Results regarding lift, drag, pitching moment, hinge moment, and rolling moments were obtained for several Mach numbers, a constant Reynolds number, and a range of angles of attack.
Date:
July 22, 1952
Creator:
Boyd, John W.
System:
The UNT Digital Library
Aerodynamic heating of rocket-powered research vehicles at hypersonic speeds
From Introduction: "The purpose of this paper is to present and discuss skin temperature measurements from two flight tests. Temperature measurements were obtained to a Mach number of 5.4 on the first flight and to a Mach number of 10.4 on the second flight."
Date:
July 19, 1955
Creator:
Piland, Robert O. & Collie, Katherine A.
System:
The UNT Digital Library
Aerodynamic Investigation of a Cup Anemometer
Results of an investigation wherein the change of the normal force coefficient with Reynolds Number was obtained statically for a 15.5-centimeter hemispherical cup.
Date:
July 1934
Creator:
Hubbard, John D. & Brescoll, George P.
System:
The UNT Digital Library
Aerodynamic Loads on Tails at High Angles of Attack and Sideslip
"Results are presented for the loads and moments acting on the individual tail surfaces of a body-tail combination over a wide range of angles of attack and sideslip. The effects of forebody length and panel-panel interference on the characteristics are included. It is shown that large nonlinear variations in these loads and moments, which occur at some combinations of angle of attack and sideslip, cannot be predicted by low-angle theory" (p. 1).
Date:
July 23, 1957
Creator:
Spahr, J. Richard & Polhamus, Edward C.
System:
The UNT Digital Library
Aerodynamic Properties of Slender Wing-Body Combinations at Subsonic, Transonic, and Supersonic Speeds
From Introduction: "In an incomprehensible medium, the mutual interference of a fuselage and wing of high-aspect ratio (to which lifting-line theory is applicable) has been treated by Lennertz, Wiselsberger, Pepper, and Multhopp in reference 1, 2, 3, and 4. It is the purpose of this note to treat the effect of on the aerodynamic loading of the mutual interference between a low-aspect-ratio pointed wing and a fuselage consisting of a slender body of revolution."
Date:
July 1948
Creator:
Spreiter, John R.
System:
The UNT Digital Library
Aerodynamic Research on Fuselages with Rectangular Cross Section
The influence of the deflected flow caused by the fuselage (especially by unsymmetrical attitudes) on the lift and the rolling moment due to sideslip has been discussed for infinitely long fuselages with circular and elliptical cross section. The aim of this work is to add rectangular cross sections and, primarily, to give a principle by which one can get practically usable contours through simple conformal mapping. In a few examples, the velocity field in the wing region and the induced flow produced are calculated and are compared with corresponding results from elliptical and strictly rectangular cross sections.
Date:
July 1958
Creator:
Maruhn, K.
System:
The UNT Digital Library