Recent results on the D*, F, and F* production in e+e- from HRS and MARK III are summarized. An improved upper limit on the decay width of D* is reported. A brief review of the characteristics of F and the updated data of the F production in e/sup +/e/sup -/ are given. A new measurement on F* is made using the associated production method in the reaction e/sup +/e/sup -/ ..-->.. FF*.

We review the theory of the Mikheyev-Smirnov-Wolfenstein effect, in which matter oscillations can greatly enhance ''in vacuo'' neutrino oscillations, and we examine its consequences for the solar neutrino problem. Using a two-flavor model, we discuss the solutions in the ..delta..m/sup 2/-sin/sup 2/2THETA parameter space for the /sup 37/Cl experiment, and describe their predictions for the /sup 71/Ga experiment and for the spectrum of electron-neutrinos arriving at earth. We also comment on the three-flavor case.

In order to see if there could be agreement between results of stellar evolution theory and those of nonradial pulsation theory, calculations of white dwarf models have been made for hydrogen surface masses of 10/sup -4/ solar masses. Earlier results indicated that surface masses greater than 10/sup -8/ solar masses would not allow nonradial pulsations, even though all the driving and damping is in surface layers only 10/sup -12/ of the mass thick. It is shown that the surface mass of hydrogen in the pulsating white dwarfs (ZZ Ceti variables) can be any value as long as it is thick enough to contain the surface convection zone. 10 refs., 6 figs.

The field quality data from the R and D SSC 4.5m-long dipoles are summarized and compared to SSC requirements. In most respects, the magnets exceed the requirements. Modifications incorporated into the 16.6m magnets are expected to correct the few deficiencies. Specific aspects of the magnet design are discussed in terms of their effect on particular multipoles and the time required for modifications.

Mid-water trawling techniques were used during September to estimate kokanee population abundance, structure and survival. Abundance in 1985 was estimated at 4.5 million fish (198 per hectare), down from over 12 million kokanee in 1974 when the population was first monitored. Hatchery fry production (<6 million annually) has stabilized kokanee abundance since its initial decline in the late 1960s. Wild fry recruitment has remained relatively stable at 1.8 million since 1978; whereas recruitment of hatchery-reared fry has ranged from 0.09 to 1.98 million. The 1985 creel survey indicated that kokanee harvest rates remain low, with approximately one kokanee harvested per hour of effort from April to August. Catch rates were as high as 3.5 fish per hour during the mid-1960s. The zooplankton community was monitored with periodic plankton tows. Zooplankton composition in 1985 was similar to previous years and appears to have stabilized following the introduction of mysids, with peak cladoceran production occurring several weeks after peak kokanee emergence. Delayed release of hatchery fry resulted in higher survival of hatchery (7.3%) than wild (0.43%) kokanee fry. Other release strategies will be tested as more fry become available.

A process for the removal of hydrogen sulfide from coal-derived gas streams has been developed. The basis for the process is the absorption of H/sub 2/S into a polar organic solvent where it is reacted with dissolved sulfur dioxide to form elemental sulfur. After sulfur is crystallized from solution, the solvent is stripped to remove dissolved gases and water formed by the reaction. The SO/sub 2/ is generated by burning a portion of the sulfur in a furnace where the heat of combustion is used to generate high pressure steam. The SO/sub 2/ is absorbed into part of the lean solvent to form the solution necessary for the first step. The kinetics of the reaction between H/sub 2/S and SO/sub 2/ dissolved in mixtures of N,N-Dimethylaniline (DMA)/ Diethylene Glycol Monomethyl Ether and DMA/Triethylene Glycol Dimethyl Ether was studied by following the temperature rise in an adiabatic calorimeter. This irreversible reaction was found to be first-order in both H/sub 2/S and SO/sub 2/, with an approximates heat of reaction of 28 kcal/mole of SO/sub 2/. The sole products of the reaction appear to be elemental sulfur and water. The presence of DMA increases the value of the second-order rate constant by …

This thesis introduces a new non-perturbative technique into quantum field theory. To illustrate the method, I analyze the much-studied phi/sup 4/ theory in two dimensions. As a prelude, I first show that the Hartree approximation is easy to obtain from the calculation of the one-loop effective potential by a simple modification of the propagator that does not affect the perturbative renormalization procedure. A further modification then susggests itself, which has the same nice property, and which automatically yields a convex effective potential. I then show that both of these modifications extend naturally to higher orders in the derivative expansion of the effective action and to higher orders in the loop-expansion. The net effect is to re-sum the perturbation series for the effective action as a systematic ''accelerated'' non-perturbative expansion. Each term in the accelerated expansion corresponds to an infinite number of terms in the original series. Each term can be computed explicitly, albeit numerically. Many numerical graphs of the various approximations to the first two terms in the derivative expansion are given. I discuss the reliability of the results and the problem of spontaneous symmetry-breaking, as well as some potential applications to more interesting field theories. 40 refs.

This report describes a mathematical model that estimates the rate that cesium and iodine isotopes would migrate from spent fuel rods after emplacement in a geologic repository that is subsequently flooded with ground water. 4 refs., 2 figs. (TEM)

This paper presents a design chart to aid designers in the selection of a wall thickness for long cylindrical shells having atmospheric pressure outside the shell and a pressure less than atmospheric inside the shell. The chart indicates a conservative value for the minimum wall thickness for a given shell diameter and material when the shell is completely evacuated.

Penetrations may result from corrosion or cracking and may be through the container material or through deposits of corrosion products. The analysis deals with the resultant radionuclide transport, but not with how these penetrations occur. We provide numerical illustrations for diffusive nuclide flux through these apertures from mathematical expressions. 2 refs., 2 figs.

This report describes mathematical predictions for the migration of radionuclides from an emplaced radioactive waste container. The model assumes a spherical-equivalent waste solid surrounded by backfill but neglects the effect of decay heat. 7 refs., 2 tabs. (TEM)

In 1978 a literature search on selective blocking of fluid flow in porous media was done by Professor S.S. Marsden and two of his graduate students, Tom Elson and Kern Huppy. This was presented as SUPRI Report No. TR-3 entitled ''Literature Preview of the Selected Blockage of Fluids in Thermal Recovery Projects.'' Since then a lot of research on foam in porous media has been done on the SUPRI project and a great deal of new information has appeared in the literature. Therefore we believed that a new, up-to-date search should be done on foam alone, one which would be helpful to our students and perhaps of interest to others. This is a chronological survey showing the development of foam flow, blockage and use in porous media, starting with laboratory studies and eventually getting into field tests and demonstrations. It is arbitrarily divided into five-year time periods. 81 refs.

The technology for producing high fields in large superconducting magnets has increased greatly in recent years, but must increase still more in the future. In this paper, we examine the present state of the art vis-a-vis the needs of a next-generation fusion machine and outline a program to provide for those needs. We also highlight recent developments that suggest the program goals are within reach.

The time history of the central toroidal plasma rotation velocity in Tokamak Fusion Test Reactor (TFTR) experiments with auxiliary heating by neutral deuterium beam injection and major-radius compression has been measured from the Doppler shift of the emitted TiXXI-K..cap alpha.. line radiation. The experiments were conducted for neutral beam powers in the range from 2.1 to 3.8 MW and line-averaged densities in the range from 1.8 to 3.0 x 10/sup 19/ m/sup -2/. The observed rotation velocity increase during compression is in agreement with results from modeling calculations which assume classical slowing-down of the injected fast deuterium ions and momentum damping at the rate established in the precompression plasma.

An array of three portable, pressurized ionization chambers (PICs) measured short-term external radiation levels produced by air activation products from the Los Alamos Meson Physics Facility (LAMPF). The monitoring was at the closet offsite location, 700-900 m north and northeast of the source, and across a large, deep canyon. A Gaussian-type atmospheric dispersion model, using onsite meteorological and stack release data, was tested during their study. Monitoring results indicate that a persistent, local up-valley wind during the evening and early morning hours is largely responsible for causing the highest radiation levels to the northeast and north-northeast of LAMPF. Comparison of predicted and measured daily external radiation levels indicates a high degree of correlation. The model also gives accurate estimates of measured concentrations over longer periods of time.

This document presents guidance to management on how to proceed in determining if the quantity of nonradioactive toxic materials in any Pacific Northwest Laboratory (PNL) or PNL-managed facility constitutes a potential threat to the public or to employees outside the facility. The ''Immediately Dangerous to Life or Health'' concept developed by the Department of Health, the Institute of Occupational Safety and Health, the Occupational Safety and Health Administration, and contractors who work with these organizations has been used as the measuring device to determine potential effects. The hazard classes (low, moderate and high) defined in the Department of Energy Order 5481.1A have been used to determine the seriousness of the potential effects. The management requirements related to the hazard classification have also been included.

The concept of multiplexing for a fusion power core as an option for producing power is explored. Superconducting, as well as normal magnet, coils in either first or second stability regimes are considered. The results show that multiplex plants with superconducting magnets operating in the second stability regime could be competitive with the single-unit plants in some unit sizes. The key issues that impact the expected benefits of multiplexing must be investigated further. These are factory fabrication, economy of scale, the extent of equipment sharing, inherent safety, maintainability, and utility load management.

A brief review is given of selected topics in the electromagnetic structure of nucleons and nuclei, including nucleon form factors from both quantum chromodynamics and electron scattering data, measurements of the deuteron and triton form factors, quasi-elastic scattering, and the EMC effect. 47 refs., 13 figs. (LEW)

The extent of predation on juvenile salmonids in John Day Reservoir was determined. Salmonids were the single most important food item by weight for northern squawfish (Ptychocheilus oregonensis) in the restricted zones at McNary tailrace and John Day forebay during all sampling periods. Salmonids accounted for 18.1% of the weight in the diet of walleyes (Stizostedion vitreum vitreum) in 1984 which was at least twice that found in previous years. In smallmouth bass (Micropterus dolomieui) salmonids contributed little to their diet whereas for channel catfish (Ictalurus punctatus) fish accounted for 64.1% of the weight in their diet with salmonids responsible for approximately half of this weight. An intensive search of the fisheries literature was conducted to review various fish capture and control techniques which might have potential as predation control measures for the major predators of juvenile salmonids in the Columbia River system. Most prey protection measures were judged to have high potential and direct predator control measures were judged to have moderate or low potential.

High Energy Gas Fracturing is a tailored pulse fracturing technique which uses propellants to obtain controlled fracture initiation and extension. Borehole pressurization rates can be tailored, by suitable choice of propellants, to produce four or eight fractures radiating from the wellbore. High Energy Gas Fracture (HEGF) research is conducted at DOE's Nevada Test Site (NTS) in a tunnel complex where experiments can be done under realistic in situ stress conditions (1400 psi (9.7 MPa) overburden stress). Pressure measurements are made in the test borehole during all fracturing experiments. Experiments are mined back to provide direct observation of fracturing obtained. The initial objective of HEGF research was to develop multiple fracturing technology for application in gas well stimulation. HEGF research at NTS and in Devonian shale demonstration tests has resulted in a completed technology for multiple fracturing in uncased, liquid-free wellbores. Current resarch is directed toward extending the technique to liquid-filled boreholes for application in geothermal in addition to gas and oil wells. For liquid-free boreholes, multiple fracturing is specified in terms of pressure risetime required for a given borehole diameter. Propellants are mixed to achieve the desired risetime using a semiempirical mixing equation. The same techniques were successfully applied to …

During fiscal year 1982, the US Department of Energy (DOE) assigned responsibility for managing civilian nuclear waste treatment programs in the United States to the Nuclear Waste Treatment Program (NWTP) at the Pacific Northwest Laboratory (PNL). One of the principal objectives of this program is to establish relationships between vitrification process control and glass quality. Users of the liquid-fed ceramic melter (LFCM) process will need such relationships in order to establish acceptance of vitrified high-level nuclear waste at a licensed federal repository without resorting to destructive examination of the canisters. The objective is to be able to supply a regulatory agency with an estimate of the composition, durability, and integrity of the glass in each waste glass canister produced from an LFCM process simply by examining the process data collected during the operation of the LFCM. The work described here will continue through FY-1987 and culminate in a final report on the ability to control and monitor an LFCM process through sampling and process control charting of the LFCM feed system.

This is the fifth in a series of reports to document the use of a methodology developed by the Pacific Northwest Laboratory to calculate, for prioritization purposes, the risk, dose and cost impacts of implementing resolutions to reactor safety issues (NUREG/CR-2800, Andrews et al. 1983). This report contains results of issue-specific analyses for 23 issues. Each issue was considered within the constraints of available information as of winter 1986, and two staff-weeks of labor. The results are referenced, as one consideration in setting priorities for reactor safety issues, in NUREG-0933, &#x27;&#x27;A Prioritization of Generic Safety Issues.&#x27;&#x27;

When completed, the Laser Electron Gamma Source (LEGS) is expected to provide intense beams of monochromatic and polarized (circular or linear) gamma rays with energies up to 500 MeV. The gamma-ray beams will be produced by Compton backscattering uv laser light from the electrons circulating in a storage ring. Progress with installation of the facility is described, particularly the Ar-ion laser and tagging spectrometer. Tests of the tagging spectrometer coponents is reported, and a second laser is described for higher energy operation. Estimates are given of expected beam parameters. Experimental equipment for the planned research projects to be carried out at the LEGS facility is discussed. (LEW)

Pacific Northwest Laboratory studies, aimed at defining appropriate glass compositions for future disposal of high-level wastes, have developed composition ranges for the waste that will likely result during reprocessing of Light Water Reactor (LWR) and Liquid Metal Reactor (LMR) fuels. The purpose of these studies was to provide baseline waste characterizations for possible future commercial high-level waste so that waste immobilization technologies (e.g., vitrification) can be studied. Ranges in waste composition are emphasized because the waste will vary with time as different fuels are reprocesses, because choice of process chemicals is nuclear, and because fuel burnups will vary. Consequently, composition ranges are based on trends in fuel reprocessing procedures and on achievable burnups in operating reactors. In addition to the fission product and actinide elements, which are the primary hazardous materials in the waste, likely composition ranges are given for inert elements that may be present in the waste. These other elements may be present because of being present in the fuel, because of being added as process chemical during reprocessing, because of being added during equipment decontamination, or because of corrosion of plant equipment and/or fuel element cladding. This report includes a discussion of the chemicals added in variation …