Report presenting an investigation in an altitude test chamber to evaluate the performance of an axial-flow turbojet engine over a range of engine-inlet Reynolds numbers. Reducing the engine inlet Reynolds number resulted in a reduction of corrected air flow and compressor efficiency but did not affect the compressor pressure ratio at a given corrected engine speed.

Report presenting an investigation in the transonic tunnel on the effect of sweepback angle on the wing-body characteristics at a range of Mach numbers. Results regarding lift characteristics, drag characteristics, and pitching-moment characteristics are provided.

Memorandum presenting an experimental investigation of the elastic compressive buckling strength of plates with various configurations of integral stiffening. Some of the configurations tested included ribbing that was longitudinal, transverse, longitudinal, and transverse, and skewed at various angles to the sides of the plates to form a diamond or waffle-like pattern. The results indicate that the waffle-like stiffening is of sufficient structural interest to merit further study of the plastic buckling and fabrications aspects.

"An experimental investigation in the Langley Gas Dynamics Laboratory has been made of the flow separation from slender rods mounted to extend forward along the axes of symmetry of blunt-nosed bodies. The mechanism of the separation and its governing criteria are discussed. Drag data at a Mach number of 2.72 for various rod lengths and nose radii at an angle of attack of zero degrees are presented. It was found that the drag coefficients of blunt noses could be appreciably reduced by the use of protruding rods. Criteria for rod length which gives lowest drag are given" (p. 1).

Report presenting an investigation of the performance of several conical cooling-air ejectors at primary jet pressure ratios from 1 to 10, secondary shroud pressure ratios from 0.60 to 4.00, and primary to secondary temperature ratio of 1.0. The investigation centered on primary air flow, secondary air flow, primary nozzle thrust, and gross ejector thrust.

Report presenting analytical methods to calculate average and local turbine-blade temperatures. The temperatures were compared with experimental data obtained in a forced-convection, water-cooled aluminum turbine over a range of turbine-inlet-gas temperatures and coolant-mass velocities. Results regarding comparison of calculated and experimental aluminum turbine blade temperatures, comparison of calculated and experimental stationary-blade temperatures, stationary water-cooled blade operating data, and turbine operating data are provided.

Report presenting an adhesive, FPL-710, which produces higher strength at temperatures up to 600 degrees Fahrenheit than previously obtained and possesses good resistance to aging at high temperatures. It also has acceptable resistance to creep and immersion in various organic solvents. Results regarding its strength properties, heating and aging resistances, and variables affecting bond strength are provided.

Report presenting an attempt to determine the reliability and calibration of the Langley transonic tunnel in the open slotted test section. Results regarding test-section calibration, including flow uniformity, calibration, and angularity, model testing and boundary interference, and reduction of interference are provided.

A slug of air-saturated distilled water was circulated for 317 hours at a velocity of 15 feet per second in an AISI 347 stainless-steel toroid with a wall temperature of 500 F and a 30 F difference in temperature between the hot and cold sections. The depth of corrosion layer was 0.001 inch (0.028 in./yr) in the hot sector and 0.0007 inch (0.019 in./yr) in the cold sector; no mass transfer was observed. The results of gas,water,and X-ray diffraction analyses are given together with photomicrographs of sections taken from the hot and cold sections of the specimen.

Report presenting measurements of lift made on various rectangular-plan-form wings differing in trailing-edge thickness, profile shape, maximum thickness ratio, and aspect ratio. Experiments were conducted at a range of Mach numbers, Reynolds numbers, and wings with and without boundary-layer trips. Results regarding a comparison of experimental results with theory at moderate supersonic Mach numbers and calculations for hypersonic Mach numbers are provided.

Report that is part of a program to investigate the aerodynamic characteristics in pitch, yaw, and steady roll of various model configurations with variations in the wing geometric parameters. The paper presents the aerodynamic characteristics in pitch of wing-fuselage combinations with wings of aspect ratio 4, taper ratio of 0.6, and sweep angles varying from 3.6 degrees to 60 degrees. Results regarding lift characteristics, pitching-moment characteristics, drag characteristics, and lift-drag ratios are provided.

From Introduction: "Design studies of long-range supersonic missiles indicate the Mach number range of 3 to 4 to be of considerable promise. Accordingly, the NACA is conducting research on the performance of a wide variety of supersonic diffusers in this range. The initial phase of this research is concerned primarily with the characteristics of conventional axially symmetric diffusers operating at design values of flight Mach number."

Report presenting an investigation in the high-speed wind tunnel to determine the aerodynamic characteristics of three triangular wings and a trapezoidal wing through the transonic speed range by use of the bump technique. Data was obtained over a range of Mach and Reynolds numbers. Results regarding the lift, drag, pitching moment, and lift-drag ratio of the various wings are provided.

Report presenting surveys of the distribution of total pressure, total temperature, and static pressure at a number of stations in the slotted test section and diffuser of the transonic tunnel with early and improved diffuser-entrance noses installed at the ends of the slots. Results regarding power losses with the original diffuser-entrance nose, development of revised diffuser-entrance noses, and energy losses in the tunnel with the final diffuser-entrance nose are provided.

From Introduction: "In the present paper, which supplements reference 1, V-g records obtained from F8F-2 airplanes in 1949 are analyzed statistically to determine the frequency of experiencing large values of normal load factor and airspeed. These results are compared with the results from the F8F-1 airplane."

Memorandum presenting an investigation conducted to determine the effects of scale and compressibility on the forces, moments, and pressure distribution on a cambered and twisted wing with an aspect ratio of 3.0 and a taper ratio of 0.5. Lift, drag, and pitching-moment data and the chordwise distribution of static pressure at seven spanwise stations are presented for specified Mach and Reynolds numbers. In order to determine the effects of camber and twist, the force, moment, and pressure data are compared with the data for an uncambered and untwisted wing of the same plan form.

Report presenting a wing-body combination with a plane tapered wing of aspect ratio 3.1, taper ratio of 0.39, and 3-percent-thick, rounded-nose sections in streamwise planes at subsonic and supersonic Mach numbers. The lift, drag, and pitching moment are presented for a range of Mach numbers and Reynolds numbers.

Report presenting a study of the literature data on the solubility of water in hydrocarbons, which includes information about the log of solubility, critical solution temperature, and ratios that may affect solubility are provided. An equation is presented and applied to a few petroleum fractions ranging from gasoline to lubricating oil, and a comparison of calculated and experimental solubilities is provided.

"A brief study was made of the effects of slots in a test-section wall on the reflection from the wall of an incident oblique shock wave at a free-stream Mach number of 1.62. The reflection was observed with an interferometer for various combinations of slot width, spacing, and contour. The reflections from the open and the closed portions of the wall, being at different angles to the wall, were not superimposed and, therefore, did not cancel each other" (p. 1).

"The experimental performance of a modified turbine for driving a supersonic compressor is presented and compared with the performance of the original configuration to illustrate the effect of small changes in the ratio of nozzle-throat area to rotor-throat area. Performance is based on the performance of turbines designed to operate with both blade rows close to choking. On the basis of the results of this investigation, the ratio of areas is concluded to become especially critical in the design of turbines such as those designed to drive high-speed, high-specific weight-flow compressors where the turbine nozzles and rotor are both very close to choking" (p. 1).

Report presenting an investigation to determine the effects of dual-rotation propeller operation at high thrust on the static longitudinal stability characteristics of a semispan powered model representing a twin-engine airplane configuration with flaps retracted. Stability and trim changes associated with an extreme constant power conditions were greatly dependent on tail height and vertical location of the center of gravity. Results regarding basic data, effects of power on overall stability and trim, and tuft-grid flow surveys are provided.

Report presenting free-flight tests made with four fin-stabilized bodies of fineness ratio 8.91 to determine the effect of body cross-sectional shape on body drag at a range of Mach and Reynolds numbers. Results regarding the curve of drag coefficients, drag on the nose and body, and body pressure drag are provided.

Report presenting the results of an investigation of flap-type controls on a low-aspect-ratio triangular wing using NACA 0005-63 sections for a constant-chord and a constant-percent-chord control surface. Two flap profiles were investigated: one with a true contour and the other with a blunt trailing edge. Results regarding lift, drag, pitching moment, hinge moment, and rolling moments were obtained for several Mach numbers, a constant Reynolds number, and a range of angles of attack.

Report presenting an experimental investigation of the flow field downstream of a canard-type control surface and in the vicinity of a symmetrical body in the 8- by 6-foot supersonic tunnel at Mach numbers of 1.8 and 2.0. The results indicated severe total pressure losses and large flow deflections in the control surface wake.