From Introduction: "An investigation has been conducted in the N.A.C.A. full-scale wind tunnel to determine the aerodynamic characteristics of a 1/4-scale model of a 4-engine monoplane when equipped with comparable air-cooled engine and liquid-cooled engine installations. The air-cooled engine installation consisted of nacelles equipped with N..A.C.A. cowlings and oil coolers located in the leading edge of the wing."

"In the course of an investigation to find a satisfactory vertical tail for the XP-62 airplane, a 0.45-scale vertical tail model on a stub fuselage was tested in the Langley 7- by 10-foot tunnel. This model was fitted with a flat plate to represent the horizontal tail surface. The data are presented herein for their general interest value rather than their application to this particular airplane" (p. 1).

From Introduction: "Certain alternations of a qualitative nature may be performed in spite of the fact that a pressure change cannot be prescribed. It is the purpose of this paper to indicate a method by which qualitative alternation may be performed. It will be noted that the present method of contour modification will serve the intended purpose of the inverse method."

"Increments in structural loads due to atmospheric turbulence can be accurately expressed in terms of flight speed and effective gust velocities (reference 4). Data from which the effective gust velocities could be computed were also obtained during the flights of the XC-35 airplane. These data have been used to determine the significance of the fluctuations in the pilot's indicated-airspeed readings in relation to structural loads to due to atmospheric turbulence" (p. 3).

From Introduction: "This paper contains data on the mechanical properties of sand-cast test bars having a considerable range in zinc, magnesium, and copper content and more detailed data on the properties and foundry characteristics of an aluminum-zinc-magnesium-copper alloy having a preferred composition for high strength and ductility."

From Summary: "The independent variables considered in the analysis included stress-concentration factor, stress-load relation, wing loading, design and cruising speeds, design gust velocity, and airplane size. Several methods for estimating fatigue life from gust frequencies are discussed."

Availability data obtained on SNB-1 trainer-class airplanes were analyzed and results presented as flight envelopes which predict occurrences of large values of air speed and acceleration. Comparison is made with SNJ-4 trainer-class airplane data analyzed by the same method. It is concluded that flight envelopes are satisfactory; that the two types show large differences in flight loads and speeds experience; and that SNB-1 will seldom, if ever, exceed design limit load factor and restricted speed, which SNJ-4 can be expected to exceed design-limit load factor and restricted speed in a very small number of flight hours.

Report presenting an investigation to obtain blade design data for high-efficiency axial-flow fans and compressors, which were carried out in a two-dimensional low-speed cascade tunnel. The effects of camber, solidity, and stagger on blade turning angle and the shape of pressure distributions were determined for a family of five low-drag airfoils.

Report presenting an analytical study of the influence of full-span slotted and Fowler flaps on the requirements for horizontal tail surfaces. The elevator deflection required to land at three-point attitude, elevator deflection required to stall the airplane at altitude, and permissible center-of-gravity range have been calculated for a fighter-type airplane.

Report presenting the calibrations of three types of service pitot-static tubes over an approximate range of speeds of 150 to 600 miles per hour. The calibrations indicated a need for a pitot-static tube with greater accuracy, especially at higher speeds. Results regarding the service tubes, Prandtl tube, Eigh-speed tube, and a comparison of the tubes are provided.

Report presenting column and plate compressive strengths of extruded 24S-T aluminum alloy determined both within and beyond the elastic range from tests of thin-strip columns and local-instability tests of H-, Z-, and channel-section columns. The tests are part of a research investigation to provide data on the structural strength of various aircraft materials. Results regarding compressive stress-strain curves and column and plate compressive strengths are provided.

Column and plate compressive strengths of extruded 24S-T aluminum alloy were determined both within and beyond the elastic range from tests of thin-strip columns and local-instability tests of H-, Z-,and channel-section columns. These tests are part of an extensive research investigation to provide data on the' structural strength of various aircraft materials. The results are presented in the form of curves and charts that are suitable for use in the design and analysis of aircraft structures.

Report presenting column and plate compressive strengths of extruded 75S-T aluminum alloy both within and beyond the elastic range from tests of thin-strip columns and local-instability tests of H-, Z-, and channel-section columns. The tests are part of an extensive research investigation to provide data on the structural strength of various aircraft materials. Results regarding compressive stress-strain curves and column and plate compressive strengths are provided.

"A comparison is made of the structural efficiencies of truss webs of 24S-T aluminum alloy with previously published values of the structural efficiencies of diagonal-tension webs of 24S-T aluminum alloy on the basis of identical allowable stresses. It is concluded that the diagonal-tension beam (web and flanges) can usually be built to be a more efficient beam than the truss beam, even though over a small range the web of a Warren truss beam is slightly more efficient than the web of a diagonal-tension beam" (p. 1).

Report presenting a comparison of two flight-test procedures for the determination of the aileron control capabilities of an airplane. The procedures consist of performing rudder-fixed aileron rolls from straight unbanked flight and from steady turning flight. Results regarding rate of roll comparison and sideslip-angle comparison are provided.

Report presenting testing to obtain experimental confirmation of the effect of air compressibility on cooling and pressure loss of a baffled cylinder barrel and to evaluate various methods of analysis. Testing occurred over a wide range of air flows and density altitudes.

Report discusses the results of testing conducted to determine the performance of automatic, internal-coolant valves actuated by cylinder temperatures.The performance of the valves with respect to temperature sensitivity, rapidity of response, and hunting characteristics is described. The relative effects on cylinder performance obtained by internally supplying water and additional fuel were also examined.

Report presenting the results of comparative cooling tests run on two Wright C9GC (G-200) cylinders, one with the original steel fins and one with 1-inch spiral copper fins brazed on the barrel. Calculations were also performed using copper and aluminum fins with the same weight as the original steel fins, which showed positive results. Results regarding cylinder-temperature correlation, piston-temperature correlation, and comparative performance are also provided.

Report presenting equations relating the various dimensions, air weight flow, and performance of a cross-flow tubular intercooler in which the charge flows through and the cooling air across the tubes. A method of determining and presenting the performance of a given intercooler at various operating conditions is indicated. Results regarding the cooling effectiveness equation, effect of primary intercooler variables, design charts, effect of tube arrangement on intercooler characteristics, and performance charts are provided.

Report presenting a survey of aircraft heat exchangers in three parts: design, selection, and installation. Appendices give the physical properties of air, properties of standard atmosphere as defined by the Navy, Army, and NACA, and an impact-pressure chart.

Report presenting an analysis of data for turbulent boundary layers along wings and bodies of various shapes in order to determine the fundamental variables that control the development of turbulent boundary layers. Results indicate that the type of velocity distribution in the boundary layer could be expressed in terms of a single parameter.

Report presenting a technique of testing wind tunnel powered models developed as a result of experience gained in the investigation of the static longitudinal and lateral staiblity and control characteristics of several powered models in the 7- by 10-foot wind tunnel. A discussion of the conditions to be investigated, methods of presenting and interpreting the data, and a suggested operating technique are given.

From Summary: "An analysis of the nose-inlet shapes developed in previous investigations to represent the optimum from the standpoint of critical speed has shown that marked similarity exists between the nondimensional profiles of inlets which have widely different proportions and critical speeds. With the nondimensional similarity of such profiles established, the large differences in the critical speeds of these nose inlets must be a function of their proportions. An investigation was undertaken in the Langley 8-foot high-speed tunnel to establish the effects of nose-inlet proportions on critical Mach number and to develop a rational method for the design of high-critical-speed nose inlets to meet desired requirements."

Report presenting drag and cross-wind force measurements of a Browning 0.50-caliber M2 machine gun at a range of air speeds in the NACA wind tunnel. The gun protruded through the top of the tunnel wall into the air stream and tests were performed at a variety of angles in order to determine the power required to turn the gun against the aerodynamic forces and the horsepower absorbed in air drag by the protruding gun. Special attention is given to the jacket around the gun, which seems to provide the greatest amount of drag.