"The condensation of water vapor in an air has the following consequences: acquisition of heat (liberated heat vaporization; loss of mass on the part of the flowing gas (water vapor is converted to liquid); change in the specific gas constants and of the ratio k of the specific heats (caused by change of gas composition). A discontinuous change of state is therefore connected with the condensation; schlieren photographs of supersonic flows in two-dimensional Laval nozzles show two intersecting oblique shock fronts that in the case of high humidities may merge near the point of intersection into one normal shock front" (p. 1).

"The present report concerns a method of computing the velocity and pressure distributions on bodies of revolution in axially symmetrical flow in the subsonic range. The differential equation for the velocity potential Phi of a compressible fluid motion is linearized tn the conventional manner, and then put in the form Delta(Phi) = 0 by affine transformation. The quantity Phi represents the velocity potential of a fictitious incompressible flow, for which a constant superposition of sources by sections is secured by a method patterned after von Karman which must comply with the boundary condition delta(phi)/delta(n) = 0 at the originally specified contour" (p. 1).

This report shows that by applying both energy and impulse theorems the optimum throat dimension of the mixing nozzle and the best shape of intake can be predicted approximately in a relatively simple manner. The necessary length of the mixing nozzle follows from Prandtl's turbulent mixing theory. The calculations are carried out for the mixing of similar and dissimilar fluids.

"The field for curved blades is represented by a vortex series with a vortex removed at the blade point. Further, an example of calculation of a curved blade from this series is given, whereby the necessary accuracy required of the different methods in practice is shown according to the case considered" (p. 1).

In the vicinity of a body in a wind tunnel the displacement effect of the wake, due to the finite dimensions of the stream, produces a pressure gradient which evokes a change of drag. In incompressible flow this change of drag is so small, in general, that one does not have to take it into account in wind-tunnel measurements; however, in compressible flow it beoomes considerably larger, so that a correction factor is necessary for measured values. Correction factors for a closed tunnel and an open jet with circular cross sections are calculated and compared with the drag - corrections already bown for high-speed tunnnels.

"With an approach of the velocity of flight of a ship to the velocity of sound, there occurs a considerable increase of the drag. The reason for this must be found in the boundary layer separation caused by formation of shock waves. It will be endeavored to reduce the drag increase by suction of the boundary layer. Experimental results showed that drag increase may be considerably reduced by this method" (p. 1).

"In the Institute for Flight Mechanics of the DVL a reactor arrangement with a maximum output of 100 kg was investigated as an expedient for the termination of dangerous spins on an airplane of the FW 56 type. reproduce the influence of a disturbance of the steady spin condition by a pitching or yawing moment. The tests were meant to reproduce the influence of a disturbance of the steady spin condition by a pitching and yawing moment" (p. 1).

The results are presented of a triple series of tests using force measurements, pressure-distribution measurements, and air flow photographs on airfoil sections suitably selected so that comparison could be made between the experimental and theoretical results. The comparison with existing theory is followed by a discussion of the divergences found, and an attempt is made to find their explanation.

This report describes a testing machine on which 35 millimeter bearings (bore) can be run at speeds of the order of 21,000 rpm, while the following factors are recorded: 1) oil circulation through bearing and oil temperature. 2) maximum temperature of outer bearing ring, 3) radial and axial load on bearing, 4) radial, axial, and angular clearance of bearing, 5) power consumption of bearing. The experiments show that the lubrication was most reliable and oil consumption lowest when the oil was introduced through a hole in the outer or inner ring of the bearing.

From Summary: "The application of the well-known basic principle of mechanics, the principle of Jourdain, to problems of the theory of the boundary layer leads to an equation from which the equations of Von Karman, Leibenson, and Golubev are derived as special cases. The given equation may be employed in other integral methods. The present paper deals with the method of the variation of the thickness of the boundary layer. A number of new approximate formulas valuable in aerodynamic calculations for the friction distribution are derived from this procedure. The method has been applied only to laminar boundary layers, but it seems probable that it may be generalized to include turbulent layers as well."

"In a previous paper, results are presented of accurate investigations of the processes of titanium carbonization and the succeeding titanium carbide decarbonization as related to the phenomenon of the graphitization of soot by heating at a constant temperature in atmospheres of pure hydrogen and carbon monoxide. These tests showed that the processes of titanium carbonization-decarbonization in an atmosphere of pure gases without nitrogen proceed in the same direction as the analogous processes under the conditions of the production furnace. In this case, however, the presence of admixtures of nitrogen changes the quantitative results of the decarbonization process" (p. 1).

"The investigation of the flow in a centrifugal pump indicated that the flow patterns in frictional fluid are fundamentally different from those in frictionless fluid. In particular, the dead air space adhering to the section side undoubtedly causes a reduction of the theoretically possible delivery head. The velocity distribution over a parallel circle is also subjected to a noticeable change as a result of the incomplete filling of the passages" (p. 1).

"At the request of the Junkers Aircraft and Engine Construction Company, Engine Division, Dessau Main Plant, an investigation was made using the interferometer method on the two turbine-blade profiles submitted. The interferometer method enables making visible the differences in density and consequently the boundary layers that develop when a flow is directed on the profile. Recognition of the points on the profile at which separation of flow occurs is thus possible" (p. 1).

"The Institut Scientifique Experimental des Transports at Moscow established toward the end of 1925 had since its inception included in its program the study of the mechanism of plastic deformation and the problems associated with it with reference to the materials of the means of transport. Before the program thus determined upon could be carried out, it was necessary to adopt a method of research, or, more exactly, a system of such methods. Because of the modest equipment of the laboratory of the recently established institute, the choice of any particular method was determined not only by the advantages it offered but also by the resources available. As a result of a series of studies and investigations, a method was determined upon which in this paper will be denoted as the micromechanical method" (p. 1).

"The mechanical and electrical construction of a new experimental instrument for fatigue testing riveted and welded joints is described. This experimental device has the advantage of being able to stress, even with comparatively low magnetic exciter force, structural components in alternate bending by resonance vibrations up to incipient fatigue failure (p .1)".

"The present article deals with what is considered to be a simpler and more accurate method of determining, from the results of bench tests under approved rating conditions, the power at altitude of a supercharged aircraft engine, without application of correction formulas. The method of calculating the characteristics at altitude, of supercharged engines, based on the consumption of air, is a more satisfactory and accurate procedure, especially at low boost pressures" (p. 1).

"The present report, which deals with pressure-distribution measurements made on a sweptback wing with a jet engine nacelle, is similar to a report on pressure-distribution measurements on a rectangular wing with a jet engine nacelle (second partial report). Here, in investigations preliminary to high-speed measurements, as in the second partial report, useful arrangements and fillet designs have been discovered" (p. 1).

"The object of the present work is first to investigate accurately the processes during stress corrosion, in particular, for light metal alloys and, as the first part of the investigation, to determine its laws; and secondly to explain its causes for various alloys and thereby find means for its partial or complete elimination and thus make possible the production of light metal alloys free from any stress corrosion. In the present paper some of the results of the investigation are given and the fundamental problems of stress corrosion discussed" (p. 1).

"The paper presents a systematical analysis of the problem of the determination of the unsteady motion about an airfoil moving in an infinite fluid that contains a system of vortices and the determination of the hydrodynamical forces acting on the airfoil. The hydrodynamical problem is reduced to the determination of the function f (xi) which transforms conformally the external region of the airfoil into the interior of a circle. The proposed methods of determining the irrotational motion of a fluid that is produced by any motion of the airfoil are especially simple and effective if the function f (xi) is rational" (p. 1).

"The present measurements form a continuation of earlier flight tests published in a previous report for predicting the downwash at the tail of an airplane. The method makes use of the tail itself as integrating contact surface to the extent that, beginning from the measurement of the self-alignment of the elevator, the mean downwash angle and dynamic pressure at the tail are determined. The instrumental accuracy is considerably improved if the elevator is completely separate from the controls during the tests, because the effect of friction on the self-alignment of the elevator is then reduced to a minimum and a finer elevator weight balance is rendered possible" (p. 1).

"On the basis of the investigations so far completed on the behavior of PTL power plants under various operating conditions, in which the influence of the propeller characteristics is of considerable importance, the most important aspects of a control system for turbine-propeller jet power plants are deduced. A simple possible means for its concrete realization, which is also applicable to TL [NACA comment: TL, jet] power plants, is presented by means of examples. A control device of this kind is now being developed" (p. 1).

"This report presents comprehensive pressure-distribution measurements on four (4) swept-back wings (phi = 0 deg, 15 deg, 30 deg, and 45 deg) of constant chord and over a large range of angles of attack with symmetrical air flow. The distributions, experimentally obtained, were compared with theoretical ones calculated by the methods of Weissinger and Multhopp" (p. 1).

"In the search for an energy source independent of air for the propulsion of underwater craft, attention was early concentrated on T-substance. It was possible to convince the OKM [NACA comment: Navy High Command] very quickly of the importance of this material. In 1934, the first experiments were undertaken" (p. 1).

It is known that the compressibility shocks accompanying local or total supersonic flows lead to pronounced flow separations which result in unusually high energy losses on airplane wings, vanes, and in diffusers. These phenomena were investigated experimentally and theoretically.