Report presenting the results of an investigation of cross-sectional-area distribution, nacelle configuration, and landing-gear-fairing configuration on the minimum drag characteristics of a model of a four-engine bomber airplane with a low-aspect-ratio triangular wing. The lateral stability characteristics are also included.

Report presents a comparison of turbofan and turbojet engines for Mach numbers of up to 3.0 and conventional hydrocarbon fuels. There are four parts of the report: a cycle analysis of turbofan engines and information about their designs, a comparison of several commercial engines proposed for the Air Force, component performance and development problems for turbofan and turbojet engines, and a summary and conclusions based on mission studies.

Report presenting an experimental investigation to determine the effects of simulated engine nacelles on the flutter characteristics of a cambered A-plan-form wing with 45 degree sweepback of the leading edge, an aspect ratio of 3.6, and a taper ratio of 0.14. Results regarding a wing-mount fixed and a model with wing mount free are provided.

Report discussing testing of two models of the Chance Vought Regulus II missile to determine its drag characteristics for a range of Mach numbers. The measured total-drag-coefficient data was extrapolated to external-drag-coefficient data and presented.

Memorandum presenting a low-velocity-turning stator designed to reduce secondary-flow loss cores by turning the flow at low velocities and accelerating it in passages of constant flow angle with reduced cross-channel pressure gradients. Performance of the stator was determined with static-pressure measurements and detailed surveys of total pressure and flow angle made with the turbine operating at design speed near design work.

Memorandum presenting a brief summary of the recent theoretical and experimental work on local heat-transfer rates on blunt-nose bodies. Results regarding the calculation of local flow conditions, prediction of stagnation-point heating rates, and calculation of heating rates over entire nose are provided.

Report presenting an investigation to determine the effectiveness of studying the dynamic characteristics of a low-speed slowly spinning fin-stabilized rocket with a free-oscillation technique and to study certain types of behavior that have been observed in this type of missile. Results regarding the stability of the original model, the effect of reversing direction of arming propeller, the effect of increasing the size of the reversed-rotation arming propeller, the effect of removing the arming propeller, the effect of adding a spoiler nose ring to a basic model, and the effect of changes in the spin rate are provided.

Memorandum presenting the results of recent exploratory investigations of the performance of clustered jet-exit installations at Mach numbers from 0.60 to 3.05. Data presented in this report were obtained with tunnel-wall-mounted models with cold-air-jet exhaust. Results regarding base pressures, effect of boattailing, effect of afterbody-nozzle geometry, and terminal fairings are provided.

Memorandum presenting a survey of the problems introduced by the increased longitudinal stability and reduced directional stability of aircraft operating in the low supersonic speed range. Information regarding longitudinal stability and directional stability are provided.

"Results are presented for the loads and moments acting on the individual tail surfaces of a body-tail combination over a wide range of angles of attack and sideslip. The effects of forebody length and panel-panel interference on the characteristics are included. It is shown that large nonlinear variations in these loads and moments, which occur at some combinations of angle of attack and sideslip, cannot be predicted by low-angle theory" (p. 1).

Report presenting an investigation in a 16-inch-diameter simulated afterburner using gaseous hydrogen fuel. Results regarding combustion efficiency, afterburner pressure losses, spontaneous ignition, and a heat-balance check are provided.

Memorandum presenting an investigation of the hydrodynamic characteristics of a six-engine hull-type seaplane designed for supersonic flight. The configuration had four engines mounted on top of the wing in individual nacelles and two engines mounted on top of the aft section of the hull with their inlets located on top of the wing.

Report discussing the flutter characteristics of several control-surface configurations, including a wing with tip ailerons, an all-movable stabilizer, vertical tails with trailing-edge rudders, a t-tail, and some simple models of all-movable controls. Some trends of the configurations and suggestions for improving the flutter characteristics are provided.

Report presenting a flight investigation of a rocket-launched solid-fuel ram-jet engine designed to bypass cooling air around the fuel charge. The internally cooled combustor averted combustor burn-out during the flight test. Results regarding the net thrust coefficient, gross thrust coefficient, time history of the air specific impulse, and total fuel load are provided.

Report presenting an investigation using rocket-propelled model of the Convair B-58 supersonic bomber. Drag at trim lift was obtained for a range of Mach and Reynolds numbers and is compared to data from several other testing facilities.

"A turbojet engine incorporating a conventional-type afterburner was operated over a range of afterburner pressure levels from 1000 to 2000 pounds per square foot absolute and a range of engine-inlet water-air ratios from 0 to 0.08. At each pressure level and water-air ratio, the afterburner fuel flow was varied from lean blowout to maximum burner-outlet temperature" (p. 1).

The present paper summarizes and correlates broadly some of the research results applicable to fin-stabilized ammunition. The discussion and correlation are intended to be comprehensive, rather than detailed, in order to show general trends over the Mach number range up to 7.0. Some discussion of wings, bodies, and wing-body interference is presented, and a list of 179 papers containing further information is included. The present paper is intended to serve more as a bibliography and source of reference material than as a direct source of design information.

Memorandum presenting an investigation of a number of short turbojet combustor configurations for hydrogen fuel in a quarter-annulus duct. The best combustor liner consisted of an annular primary zone and a secondary zone composed of T-shaped channels sloping from the primary zone to the combustor wall.

Results regarding testing of steel projectiles fired into copper targets at velocities from 5,000 to 11,500 feet per second, which indicated that as target temperature is increased, the crater size also increases. Twenty-two caliber steel cylinders and steel spheres were used as projectiles.

Memorandum presenting a study of the static stability and control problems associated with several hypersonic boost gliders. Generally, it is possible to obtain the desired trim features. Results regarding the high-lift-drag-ratio type of gliders and low-lift-drag-ratio type of gliders are provided.

Chemical sublimation has been employed for boundary-layer-flow visualization on the wings of a supersonic fighter airplane in level flight at speeds near a Mach number of 2.0. The tests have shown that laminar flow can be obtained over extensive areas of the wing with practical wing-surface conditions. In addition to the flow visualization tests, a method of continuously monitoring the conditions of the boundary layer has been applied to flight testing, using heated temperature resistance gages installed in a Fiberglas "glove" installation on one wing. Tests were conducted at speeds from a Mach number of 1.2 to a Mach number of 2.0, at altitudes from 35,000 feet to 56,000 feet. Data obtained at all angles of attack, from near 0 deg to near 10 deg, have shown that the maximum transition Reynolds number on the upper surface of the wing varies from about 2.5 x 10(exp 6) at a Mach number of 1.2 to about 4 x 10(exp 6) at a Mach number of 2.0. On the lower surface, the maximum transition Reynolds number varies from about 2 x 10(exp 6) at a Mach number of 1.2 to about 8 x 10(exp 6) at a Mach number of 2.0.

Memorandum presenting a theory for evaluating the mutual interference between a wing and tip tank as extended to apply to store-pylon configurations. By using the theory and the flow-field formulas of a previous report, theoretical store-pylon side-force estimates have been made for a number of store-pylon configurations. Results regarding the theory for store-pylon side force, scope of test configurations, contribution of store and pylon to combined load, effect of store spanwise location on the store-pylon side-force coefficient, effect of pylon sweep and store chordwise location, effect of sideslip on the store-pylon side-force coefficient, effect of fins on store side-force coefficient, and interference effects between inboard and outboard stores are provided.

Memorandum presenting heat-transfer rates and pressure fluctuations at Mach numbers of 1.98 and 4.95 measured at the stagnation point of a concave hemisphere for a range of Reynolds numbers based on free-stream conditions and model diameter. Results regarding heat-transfer characteristics, heat-transfer data, and schileren photographs and stagnation point pressure measurements are provided.

Memorandum presenting an investigation at Mach numbers of 1.61 and 2.01 to examine the characteristics of a series of nine spoiler-type controls on a trapezoidal wing with the leading edge swept back 23 degrees, an aspect ratio of 3.1, and a taper ratio of 0.4. Results regarding pressure distributions, spanwise loadings, and integrated coefficients are provided.