Memorandum presenting the results of recent exploratory investigations of the performance of clustered jet-exit installations at Mach numbers from 0.60 to 3.05. Data presented in this report were obtained with tunnel-wall-mounted models with cold-air-jet exhaust. Results regarding base pressures, effect of boattailing, effect of afterbody-nozzle geometry, and terminal fairings are provided.

Memorandum presenting a study of the static stability and control problems associated with several hypersonic boost gliders. Generally, it is possible to obtain the desired trim features. Results regarding the high-lift-drag-ratio type of gliders and low-lift-drag-ratio type of gliders are provided.

From Introduction: "V-g records supplied the NACA by the Bureau of Aeronautics in 1948 and 1949 have provided additional material. These records are analyzed statistically in this report to the frequency of large values of acceleration and airspeed, and results are compared with the design requirements."

Report presenting ram-recovery and mass-flow ratios for submerged inlets at four positions on the fuselage of a model of a hypothetical fighter airplane. Results related to the inlet location and effect of angle of attack are also provided.

"Results are presented of an investigation to determine the pressure distributions on a wing with leading-edge sweepback decreasing from 45 degrees at the root to 20 degrees at the tip, an aspect ratio of 4.12, taper ratio of 0.36, and NACA 64A009 airfoil section. Tests were conducted at a Reynolds number of 3.5 x 10(exp 6) and a Mach number of 0.07 on the wing with and without 0.20 chord and 0.65 span split flaps deflected 60 degrees. These pressure distributions are analysed herein to determine the character of flow and its effect on the stability of the wing" (p. 1).

Report presenting a general analysis that allows the rolling motions of an aircraft using a displacement-response, flicker-type automatic pilot to be determined. The system is not ideal for many stabilization problems due to inherent residual oscillations, but it offers a simple and economical solution in situations in which steady state oscillations are not a problem. Results regarding some general remarks, transient and steady states, stabilization boundaries, amplitude equations, and period equations are provided.

From Summary: "Results of wind-tunnel tests are presented for a wing with the leading edge swept back 63^o and of symmetrical section in combination with a body at Mach numbers from 0.5 to 0.95 and from 1.09 to 1.51."

Report presenting an attempt to determine the reliability and calibration of the Langley transonic tunnel in the open slotted test section. Results regarding test-section calibration, including flow uniformity, calibration, and angularity, model testing and boundary interference, and reduction of interference are provided.

Report presenting an investigation of the power requirements for slotted tunnels and methods of reducing these requirements. All pressure losses reported occurred in the region between the upstream end of the entrance ball and the entrance to the diffuser and in handling air taken in through the slotted wall. Results regarding auxiliary pumping and ejector pumping are provided.

Report presenting a comparison of normal load factors measured during combat operations with those measured during an NACA flight program conducted with fully instrumented service airplanes in operational training. Results indicated that for an equal number of maneuvers, normal load factors obtained from the NACA program are greater than those obtained during combat when based on the service-limit load factor.

Report presenting hydrodynamic planing lifts obtained in a free jet at speeds from 80 to 200 fps for four planing surfaces. The surfaces tested included a flat plate, a longitudinally curved model, a cylinder, and a hydro-ski with a complex-shaped bottom. Lift data was analyzed to show the effect of speed, planing-surface configuration, trim, and wetted-length-beam ratio at high speeds.

Report presenting the performance increase resulting from the addition of fluorine to the oxygen-JP4 rocket propellant combination evaluated experimentally in a 1000-pound-thrust engine with 0, 30, and 70 percent of fluorine by weight in the oxidant. Maximum specific impulse values obtained were 259, 278, and 287 pound-seconds per pound, respectively, at a combustion pressure of 600 pounds per square inch absolute.

Report presenting a study of the acceleration characteristics of a turbojet engine equipped with variable-position inlet guide vanes in the altitude test chamber. Maximum acceleration values for 3 engines of the same model were also obtained during testing and were found to differ as much as 50 percent. Results regarding the effect of fuel step size and inlet guide vane on acceleration, effect of flight condition, reproducibility of engine acceleration, compressor pressure ratio in relation to acceleration, and acceleration with inlet air distortion are provided.

Report presenting an investigation of the performance of clustered jet-exit installations at Mach numbers from 0.60 to 3.05. The data were obtained with tunnel-wall-mounted models with cold-air-jet exhaust. Results indicated that large base-pressure drag coefficients may be encountered in the transonic and low supersonic speed range and that the best configuration in the test was boattailed between the nacelles, had a cylindrical nacelle afterbody, and a divergent nozzle with a design pressure ratio of 15.

Report presenting an investigation in the 4- by 4-foot supersonic pressure tunnel at Mach numbers of 1.41 and 2.01 to determine the stability and control characteristics of a canard-controlled airplane configuration with potentially high values of lift-drag ratio. The configurations investigated included a plane and a twisted wing with approximately 67 degrees of sweep and an aspect ratio of 2.91 and three trapezoidal canard surfaces with ratios of exposed area to wing area of 0.032, 0.076, and 0.121.

Report presenting an investigation on canard airplane configurations in preference to a trailing-edge flap or tail control. Wide ranges in control plan form, size, and position and in wing plan form were found. Interference effects between the canard and other configuration components were not serious, and those that might be can be reduced by rearrangement of the vertical tail.

Report presenting testing on the effective heats of ablation of a number of materials using supersonic arc jets at stagnation temperatures ranging from 2000 degrees F to 11,000 degrees F. Materials examined included Teflon, nylon, Lucite, polystyrene, ammonium chloride, sodium carbonate, several phenolic resins, and melamine-fiber glass laminate.

Report presenting the design procedure and experimental test results for a range of impeller speeds for two vaned diffusers of 24 and 40 vanes. Both sets of vanes were designed to give approximately the same prescribed velocity distribution on the vane surfaces and were tested with the same impeller. Results regarding overall performance and the total-pressure-loss coefficient for both vanes are provided.