Report that "describes the selection of "standard fuel cores for calibrating an ultrasonic tester designated UT-2C" (p. 3) at Hanford Laboratories.

This development work was undertaken to investigate and standardize scintillation detector and transistorized circuitry techniques in instruments used for detecting and measuring alpha and beta particles, gamma photons, and both slow and fast neutrons. At the present time, the standard radiation detection instrumentation used at Hanford employ vacuum-tube circuitry with typical detectors being ion chambers, G-M tubes, HF3 tubes, etc. The vacuum tubes require excessive battery power, and some of the circuits are adversely affected by humidity and temperature conditions.

This document authorizes the performance in accordance with the specifications noted, the PRTR Critical Tests described herein. The experiments described have the following objectives:

This paper describes the measurement of control rod strength in the PCTR. The first section outlines the theory and method of such a measurement, and the second section presents the results of the measurement of the Experimental Gas Cooled Reactor (EGCR) control rod strength. The reactor parameter actually inferred is the difference in the infinitive multiplication factor for a control rod supercell with and without the control rod in place in the supercell. These measurements are, therefore, very closely related to the measurement of k∞ for an ordinary lattice cell.

The Plutonium Recycle Test Reactor is heavy water moderated with a heavy or light water reflector contained by a complex aluminum vessel called a Calandria. ( See Figure 1). Construction of this vessel started in August, 1958, at a large West Coast vendor's plant and was completed at Hanford in December, 1959. The fabrication problems associated with a high integrity welded aluminum vessel were generally unrealized prior to this period. This report covers the fabrication of the Calandria and lists recommendations for improving the design and reducing the cost.

The Hanford water treatment plants were operated for a number of years with alum as a coagulant and activated silica as a coagulant and a polyacrylamide as a filter conditioning agent. (other polyelectrolytes may be used.) Sufficient time has elapsed to make a comparison of the two methods of operation valid and useful. Such a comparison is the purpose of this paper.

In recognition of the need for an integrated system plan for future development requirements for radiological instrumentation, this information report was written to provide the initial step concerning such a planning. The report is to be considered a basic information analysis of the present in-use plant radiological instrumentation, of the instrumentation now undergoing active development, and of the future development work contemplated.

Facilities are to be designed for installation at Hanford for the reprocessing of irradiated, low enrichment fuels from non-production reactors, see Reference 1 and 2. The initial design of the processing facilities is to be based on processing the fuels discharged from the Dresden, Yankee, Piqua, Pathfinder and Shippingport (blanket elements only) reactors. Properties of the fuels and cladding make it impossible to completely process them in existing equipment, although the separation and decontamination can be performed in existing facilities once the fueks have been placed in solution form.

The purpose of this document is to describe the design and construction of a full-scale, electrically-heated model of a 19-rod PRTR fuel element for use in heat transfer experiments.

This is the third of a series of reports describing the phases of a study of the wear and galling of autoclavedZircaloy-2 by various bearing surface materials. The first report (1) showed that increasing contact area between the autoclaved Zircaloy-2 surfaces will not prevent scratching. It also showed that metals softer than Zircaloy-2 in general do not scratch it. The second report (2) described how eight metals and alloys were wear-tested on autoclaved Zircaloy-2 as prospects for fuel element support-bearing surface materials.

Applications of sheathed (metal) thermocouples may require in many instances, the insertion of the thermocouple thermal junction into an area that must be hermetically sealed to the outside. This same area usually contains highly reactive heat transfer medium such as an eutectic alloy of sodium and potassium of sodium alone. When fissionable materials are being irradiated, fission products that are driven off would also be present and must be contained under varying temperatures and pressures.