This report is a manual describing the methods developed by Stokes (1) and Warren and Averbach (2) (3) for the determination of the effects of cold work by x-ray diffraction methods. Only the method of mathematical analysis is presented while the method of obtaining the necessary x-ray diffraction patterns is not mentioned. This manual will be used for an experimental study of irradiation damage to uranium.

This report describes the results of evaluation tests made on several glass-coated bayonet heaters supplied to Separations Equipment Development by the Pfaudler Company. The glass-coated heaters were found to be resistant to thermal shock, mild mechanical shock, and chemical attack by boiling 60% nitric acid.

A new model High Range Beta-Gamma Survey Instrument, refer to blueprint numbers H-4-2760 and H-4-2761, was designed which utilizes a circuit similar to that of the older model but incorporates three ranges of 0-5 R/hr, 0-50 R/hr, and 0-500 R/hr.

This paper presents values of the constant B², commonly called the buckling, when 0 vanishes on the surface of a right elliptic cylinder.

A new type of flexible hose connector consisting of a Teflon tube enclosed in a stainless steel wire braid sheath was proposed for use on 105-C rear face in late 1954. A test was initiated to determine the suitability of Teflon, and specifically Fluoroflex Teflon compound for rear face application. Probable useful life limit is estimated at 10⁶ R, which would be attained in about three years in contact with fresh effluent.

The primary objective of the tests described herein was to determine if the standard five bend connector (drawing H-1-23475) and/or the T. F. Robinson three bend connector (drawing SK-1-20855) fabricated from Type 304 stainless steel tubing would satisfy the requirements of the K reactors. Results of the tests show that the standard five bend connector made from Type 304 stainless steel 0.065 inch wall tubing, in the as bent condition, with either cadmium plated Parker brass nuts and sleeves or cadmium plated high carbon steel nuts and sleeves, is suitable for installation of the K reactors.

A design study has been made of a graphite superheating reactor, a graphite moderated reactor with a heat rating of 305 Mw which produces superheated steam. It is designed for the production of plutonium and electrical power or for the production of electrical power only. The fuel elements for dual- purpose operation are U metal, while for single purpose action, they are uranium oxide. The fuel elements are cooled by a 7-pass system in which preheated water enters the bottom of the first pass and is discharged as superheated steam at the top of the seventh pass. The reactor control consists of shim control by the gas system, vertical gas-cooled control rods, vertical safety rods, and a ball safety system. Rough cost estimates indicate that the capital cost of the reactor should be comparable to other reactors of similar heat output.

Fillerwelding is a fusion welding process that provides for the automatic addition of controlled amounts of fillerwire during inert-gas-shielded tungsten-arc welding. Fillerwelding aluminum jacketed fuel elements has been successfully demonstrated and is being used on a routine basis. This manual was written to provide the necessary information to operate and maintain the fillerweld equipment.

This report constitutes the Quarterly Progress Report covering April-June 1955, for the Health Instruments Division research and development activities. Most of the studies described concern the biological fate, environmental transport of radioactive effluents, or development of instrumentation for radiation detection.

A method for determining the appropriate isotopic content of uranium-235 in uranium slugs has been investigated. In the conduct of the experiment it was found that there was a background counting rate several times the counting rate of the phenomena under study. Methods are suggested for improving the counting rate and reducing the background. The conclusions at this time are that reactivity determinations will provide the most rapid and precise measure of U-235 content in uranium.

Reactivity measurements conducted in the Hanford Test Pile are interpreted to yield resonance integrals for uranium, uranium oxide, thorium and thorium oxide. The experiments were made using cadmium filters and are discussed in terms of the multiplication factor of the Hanford Test Pile.

Values of copper tubing pressure drops as determined by test for low flow rates of air, helium, carbon dioxide and water are contained herein. The work was performed in order to provide original data, useful for design work at Hanford Atomic Products Operation, and not available in any known handbook or other publication.

Apparent excessive concentrations of atmospheric contamination which were reported to be associated with an inert-gas-shielded consumable electrode arc wielding operation were studied to evaluate the potential health hazards. A study was made of the concentrations of metal fume and gaseous products of the operation as well as the spectrum of ultraviolet radiation. Recommendations for necessary controls were made.