Abstract: The most adverse power distribution and power peaking factors have been developed for Type 3 replacement cores for SM-1, SM-1A, and PM-2A. Also included is the 37 element Type 3 core for SM-1, which is known as SM-1 Core III and is a prototype of a Type 3 core for PM-2A. The power distributions were compared with measured distributions obtained on type 3 fuel elements in SM-1, SM-1A and PM-2A core configurations. Using the measured data as a standard, correction factors were obtained and applied to the analytical predictions of the most adverse power distribution.

Abstract: Residual and fission gas release from UO2 were studied in the laboratory and in in-reactor experiments. Arc-fused powder and sintered pellets were used to determine the rate of evolution and types of residual gases as a function of temperature. Fission gas release was related to the average UO2 temperature and fission gas release calculations were made using the latest thermal conductivity values, isotopic half lives, and branching ratios available in the literature. The results obtained were compared with those available in the literature, and a satisfactory agreement was found among the groups of comparable data.

Summary: Technical report describing the testing of eight Potter Meters, for metering inlet flow and measuring exit steam qualities in the Consumers Big Rock Point Instrumented Fuel Assemblies, were individually calibrated for flow and pressure drop up to 500 gpm in the low temperature (130 F) fluid flow facility. The flow calibration comparison made with an ASME orifice installation, agreed to within + - 1 percent among seven of the meters, and meter Serial No. 8 was 2.8 percent lower than the others. Pressure drop among the meters was within about 5 percent. Locked rotor pressure drop data was obtained on one meter. A fully instrumented fuel bundle was tested in the low temperature facility and pressure drop data obtained for the tieplates and meters, spacers, and channel rods. A mock-up of the exit end of the instrumented fuel bundles, composed of 1 foot of fuel rods, tieplate, and Potter Meter was tested in the High Pressure Heat Transfer Facility. Data was obtained for single- and two-phase calibration of total flow and exit steam quality in an instrumented bundle. Each meter was operated, for a minimum of 6-8 hours after bearing modifications necessitated by seizure of the rotors, in the …

Activities in a program to develop techniques in the use of pulsed neutron sources to measure shutdown parameters related to large thermal power reactors are reported. The development of pulsed neutron source techniques for large power reactors has led to a new theoretical model recently developed by E. Garelis and J.L. Russell, Jr. The theory is presently based on a bare, one-group model with m-delayed precursors and takes all spatial modes into account. Results indicate, however, that the application of this model is much broader. Experiments were designed and carried out to both verify this new theory and to demonstrate the performance of the experimental hardware in a large power reactor.

Abstract: Hydrodynamic flow studies were conducted on a full scale model of the SM-2 reactor vessel and core. Test fluid was water at 200 psi and 200 degree F. Test facilities, model, and instrumentation design are discussed. Flow distribution in the stationary fuel elements, lattices, and control rods of the second pass was investigated. Pressure losses through the various core components were measured and are compared with calculated values. Observed over-all pressure drop was 71 feet of water at 200 degree F, 31% higher than predicted, part of which was due to presence of instrument leads. Element to element flow distribution varied approximately +-8% from pass average. Channel-to-channel stationary element flow distribution varied approximately +-10% from element average and control rod flow distribution varied from +-8.9% to +-6.4 and -11.6% depending upon rod locations. These variations exceed the original goals of a +-10% and +-12% combined deviation for stationary and control rod elements respectively, but are satisfactory in relation to thermal design. There was no indication of unsatisfactory structural performance of any components under hydrodynamic loadings up to 130% of design values. The test program was terminated after determining flow distribution in the reference core design, omitting any work on …

Describes the investigation of a particular method of extracting ions from an arc. Experimental results of a low extraction voltage ion source are given in some detail.