Report presenting an investigation of a German Jumo 004 combustor under conditions simulating zero-ram operation of a 24C jet-propulsion engine over ranges of altitude and engine speed to obtain the altitude operating limits and characteristics. Combustion efficiency, outlet-temperature distribution, and total-pressure drop were determined. The performance of the combustor with 62-octane and JP-1 fuels were also compared.

A slug of air-saturated distilled water was circulated for 317 hours at a velocity of 15 feet per second in an AISI 347 stainless-steel toroid with a wall temperature of 500 F and a 30 F difference in temperature between the hot and cold sections. The depth of corrosion layer was 0.001 inch (0.028 in./yr) in the hot sector and 0.0007 inch (0.019 in./yr) in the cold sector; no mass transfer was observed. The results of gas,water,and X-ray diffraction analyses are given together with photomicrographs of sections taken from the hot and cold sections of the specimen.

Report presenting an investigation of the applicability of a finite-step method to the calculation of subsonic spanwise load distribution, lift-curve slope, lateral center of pressure, and aerodynamic center of unusual plan forms. The 20-step method was found to generally overestimate the amount of loading at the wing tip, but the lift-curve slope, lateral center of pressure, aerodynamic center, and loading shape generally agreed with lifting-surface results.

Report presenting an experimental investigation of the flow field downstream of a canard-type control surface and in the vicinity of a symmetrical body in the 8- by 6-foot supersonic tunnel at Mach numbers of 1.8 and 2.0. The results indicated severe total pressure losses and large flow deflections in the control surface wake.

"An investigation of the use of solid fences installed on the side walls of a supersonic wind tunnel to retard the development of transverse flow and thus to increase the uniformity of the side-wall boundary layer is reported. Beneficial results were obtained with fences which had depths of the order of the boundary-layer displacement thickness and which followed potential-flow streamlines through the nozzle. Reduction of the number of fences on each side wall from four to two eliminated their effectiveness" (p. 1).

Memorandum presenting a small-scale investigation of the effects of full-span and partial-span leading-edge flaps on the aerodynamic characteristics of a sweptback wing in the 7- by 10-foot tunnel over a Mach number range of 0.70 to 1.10. Lift, drag, pitching moment, and bending moment were obtained for the basic wing and for the wing with full-span and partial-span leading-edge-flap deflections of approximately 3, 6, and 9 degrees.

Report presenting an experimental investigation to determine the performance of twin-scoop side inlets located on the fuselage of a proposed aircraft in a region of large boundary-layer thickness. Inlet configurations with subsonic and supersonic cowlings which utilized two-dimensional compression ramps and ram-type scoops for boundary-layer-removal systems were investigated at several Mach number ranges. Results regarding supersonic Mach number range, angle of attack, subsonic Mach number, and static conditions are provided.

"An investigation was conducted in the Lewis altitude wind tunnel to evaluate the performance and operational characteristics of the J40-WE-8 afterburner. A brief program of minor modifications to the flame holder, diffuser, and fuel system was undertaken to improve at a burner-inlet pressure level of 620 pounds per square foot. At this pressure level, modifications to the fuel system resulted in an increase in maximum net thrust from 1500 to 1600 pounds and a reduction in specific fuel consumption in the stoichiometric region from 3.70 to 3.15 pounds of fuel per hour per pound of net thrust" (p. 1).

Report presenting burning rates for single isooctane drops suspended in various quiescent oxygen-nitrogen atmospheres at room temperature and pressure. The burning rates were compared with those predicted by a previously developed theory based on a heat- and mass-transfer mechanism and with values predicted by a modification to the theory.

The hydrodynamic characteristics of an aerodynamically refined planing-tail hull were determined from dynamic model tests in Langley tank no. 2. Stable take-off could be made for a wide range of locations of the center of gravity. The lower porpoising limit peak was high, but no upper limit was encountered. Resistance was high, being about the same as that of float seaplanes. A reasonable range of trims for stable landings was available only in the aft range of center-of-gravity locations.

"Flight tests to determine propeller performance have been made of a Curtiss No. 838-102-18 three-blade propeller having trailing-edge extensions on a Republic P-47D-28 airplane in climb and high speed. These tests are a part of a general propeller flight-test program at the Langley Laboratory of the National Advisory Committee for Aeronautics. Results of climb tests indicate that when power is changed from approximately 1475 horsepower at 2550 rpm (roughly normal power) to 2400 horsepower at 2700 rpm (approximately military power) there is a loss in propeller efficiency of 3 percent at an altitude of 7000 feet, and 4 percent at 21,000 feet" (p. 1).

Memorandum presenting an investigation of the durabilities of several protective coatings applied to air-cooled gas turbine rotor blades of nonstrategic steels in modified turbojet engines. Four types of coatings (ceramic, nickel, Nicrobraz, and aluminized) were applied to a total of 20 blades.

A program was undertaken to determine the J73 turbojet engine compressor stall and surge characteristics and combustor blow-out limits encountered during transient engine operation. Data were obtained in the form of oscillograph traces showing the time history of several engine performance parameters with changes in engine fuel flow. The data presented in this report are for step changes in fuel flow at an altitude of 35,000 feet, at flight Mach numbers of 0.3, 0.8, and 1.2, and at several engine-inlet temperatures,.

"A program was undertaken to determine the J73 turbojet engine compressor stall and surge characteristics and combustor blow-out limits encountered during transient engine operation. Data were obtained in the form of oscillograph traces showing the time history of several engine parameters with changes in engine fuel flow. The data presented in this report are for step and ramp changes in fuel flow at an altitude of 45,000 feet and flight Mach numbers of 0 and 0.8" (p. 1).