This paper introduces new octant-range, composite-type Gauss and mid-point rule angular quadrature formulas for neutron and photon transport computations. A generalization to octant-range quadratures is also introduced in order to allow for discontinuities at material interfaces for two- and three-dimensional transport problems which can be modeled with 60-degree triangular or hexagonal mesh subdivisions in the x-y plane.

None

New VME based boards are being produced for the Run II of the Collider Detector at Fermilab (CDF). These boards are being developed and tested at both Fermilab and offsite institutions. A software framework called CDFVME has been developed in which DAQ code can be easily written to control such boards in a test stand. The framework has been used to perform diagnostics at single board, multi-board, and multi-crate levels. This software framework runs on Unix, Linux and Windows NT platforms with a Java GUI communicating via LAN to multiple intelligent front end VME crates. All distributed processes are managed by a custom CORBA based software. The system has been ported to Motorola 68K and PPC front end processors running the VxWorks real-time kernel [1].

The USDOE Material Protection Control and Accountability Program (MPC&A) has established a Project Team with the goal of providing the Russian Electrochemical Plant (ECP) with equipment and training to enable ECP to evaluate, develop, and implement a comprehensive plan and systems for physical protection, material controls, and accountancy upgrades. The MPC&A project will provide for improvements such as risk assessments, access control upgrades, computerized MC&A, communications systems upgrades, building perimeter surveillance and intrusion detection upgrades, vault upgrades, metal and nuclear material detection upgrades, along with mass measurement and non- destructive analysis (NDA) instrumentation. This paper outlines the overall objectives of the MPC&A project at the Electrochemical Plant.

For many applications, the device performance of edge emitting semiconductor lasers can be significantly improved through the use of multiple section devices. For example, cleaved coupled cavity (C3) lasers have been shown to provide single mode operation, wavelength tuning, high speed switching, as well as the generation of short pulses via mode-locking and Q-switching [1]. Using composite resonators within a vertical cavity laser opens up new possibilities due to the unique ability to tailor the coupling between the monolithic cavities, incorporate passive or active resonators which are spectrally degenerate or detuned, and to fabricate these devices in 2-dimensional arrays. Composite resonator vertical cavity lasers (CRVCL) have been examined using optical pumping and electrical injection [2-5]. We report on CRVCL diodes and show that efficient modulation of the laser emission can be achieved by either forward or reverse biasing the passive cavity within a CRVCL.

The D1 and D2 magnets, the first two types of magnets Brookhaven National Laboratory (BNL) is building for the Insertion Regions of Large Hadron Collider (LHC), are being constructed and tested in the BNL magnet test facility. The D1 magnet is cooled using 4.5 K forced flow cooling with three types of bore tube conditions. The D2 magnet is cooled using both liquid helium and forced flow cooling. The liquid cooling scheme, using the shell of the D2 cold mass as the helium vessel and a level gauge in the end volume of the cold mass for liquid control, has been successfully demonstrated. Test results prove that both D1 and D2 meet the performance requirements and that the 4.5 K liquid cooling scheme to be used for D2 and other magnets in the Insertion Regions of LHC is adequate.

THIS PAPER PRESENTS A CRYOGENIC DESIGN FOR UPGRADING THE BEIJING ELECTRON POSITRON COLLIDER AT THE INSTITUTE OF HIGH ENERGY PHYSICS IN BEIJING. THE UPGRADE INVOLVES 3 NEW SUPERCONDUCTING FACILITIES, THE INTERACTION REGION QUADRUPOLE MAGNETS, THE DETECTOR SOLENOID MAGNETS AND THE SRF CAVITIES. FOR COOLING OF THESE DEVICES, A NEW CRYPLANT WITH A TOTAL CAPACITY OF 1.0KW AT 4.5K IS TO BE BUILT AT IHEP. AN INTEGRATED CRYOGENIC DESIGN TO FIT THE BEPCII CRYOGENIC LOADS WITH HIGH EFFICIENCY IS CARRIEDOUT USING COMPUTATIONAL PROCESS ANALYSIS SOFTWARE WITH THE EMPHASES ON ECONOMICS AND SAFETY IN BOTH CONSTRUCTION AND OPERATION OF THE PLANT. THIS PAPER DESCRIBES THE CRYOGENIC CHARACTERISTICS OF EACH SUPERCONDUCTING DEVICE, THEIR COOLING SCHEMES AND THE OVERALL CRYOPLANT.

Experiments at Fermilab require an ongoing program of development for high speed, distributed data acquisition systems. The physics program at the lab has recently started the operation of a Fixed Target run in which experiments are running the DART[1] data acquisition system. The CDF and DØ experiments are preparing for the start of the next Collider run in mid 2000. Each will read out on the order of 1 million detector channels. In parallel, future experiments such as BTeV R&D and Minos have already started prototype and test beam work. BTeV in particular has challenging data acquisition system requirements with an input rate of 1500 Gbytes/sec into Level 1 buffers and a logging rate of 200 Mbytes/sec. This paper will present a general overview of these data acquisition systems on three fronts � those currently in use, those to be deployed for the Collider Run in 2000, and those proposed for future experiments. It will primarily focus on the CDF and DØ architectures and tools.

InN films grown by molecular beam epitaxy have been subjected to 2 MeV He{sup +} irradiation followed by thermal annealing. Theoretical analysis of the electron mobilities shows that thermal annealing removes triply charged donor defects, creating films with electron mobilities approaching those predicted for uncompensated, singly charged donors. Optimum thermal annealing of irradiated InN can be used to produce samples with electron mobilities higher than those of as grown films.

A plasma mirror based on a laminar water film with low flow speed 0.5-2 cm/s has been developed and characterized, for use as an ultrahigh intensity optical reflector. The use of flowing water as atarget surface automatically results in each laser pulse seeing a new interaction surface and avoids the need for mechanical scanning of the target surface. In addition, the breakdown of water does notproduce contaminating debris that can be deleterious to vacuum chamber conditions and optics, such as is the case when using conventional solid targets. The mirror exhibits 70percent reflectivity, whilemaintaining high-quality of the reflected spot.

Experimental conditions are studied to optimize transient experiments for estimating temperature dependent thermal conductivity and volumetric heat capacity. Thermal properties are assumed to vary linearly with temperature; a total of four parameters describe linearly varying thermal conductivity and volumetric heat capacity. A numerical model of experimental configurations is studied to determine the optimum conditions to conduct the experiment. The criterion D-optimality is used to study the sensor locations, heating duration and magnitude, and experiment duration for finite and semi-infinite configurations. Results indicate that D-optimality is an order of magnitude larger for the finite configuration and hence will provide estimates with a smaller confidence region.

The cylindrically symmetric beam-foil collision produces excitation and alignment of atom and ion levels similar, but not identical, to that resulting at comparable energies from ion-atom or ion-molecule collisions. When the foil is tilted, the macroscopic change acts on the microscopic scale to produce coherent alignment and orientation of the excited levels. The maximum beam energy range bounding this interaction has not yet been defined. The dynamic interaction which produces these effects is currently not predicted by any theory, although the dynamics of the ions subsequent to the collision are well understood. Refinement of current experimental technique can be expected to better define the final foil surface. The beam-tilted-foil collision promises to be useful in the study of ionic structure via quantum beat, radio-frequency and level-crossing spectroscopy techniques, and may provide a useful probe for certain surface interactions. 4 figs, 48 refs.

At ultrarelativistic energies, ionization cross sections exceed electron capture cross sections by several orders of magnitude (1,2). Effectively, all electrons transferred to a highly relativistic heavy ion moving in a solid or gaseous target medium are stripped in a relatively short distance. Above ~20 GeV/nucleon, the principal mechanism for electron capture is from pair production (ECPP) (2). The total cross sections for ECPP are te&nically important for making reliable predictions of operating limitations for relativistic heavy-ion colliders, e.g., RHIC and LHC (3). In ECPP, it is expected that ~30% of capture proceeds to excited states of the capturing ion. Some of these relatively weakly bound electrons are radiatively long-lived and easily lost in secondary collisions in solid targets, making measurements of their contributions to total capture experimentally difficult. Electrons lost from high-energy ions in collisions with target atoms form a cusp-shaped spectral peak in the forward direction in the laboratory frame centered at the velocity of the moving ion (4-5). The shape of this electron loss to projectile continuum (ELC) peak has been shown (5,6) to depend on the initial atomic bound state from which the electron is ionized. We have measured and compared ELC electrons from direct ionization of …

Validation of material models in a variety of scientific and technological applications requires accurate data regarding the high-pressure thermodynamic and mechanical properties. Traditional laboratory techniques for striking these measurements involve light gas guns to generate the required thermodynamic states, and the use of high-resolution time-resolved diagnostics to measure the desired material properties. EOS and constitutive material properties of importance to modeling needs include high-pressure Hugoniot curves and off-Hugoniot properties, such as. material strength and isentropic compression and decompression [1]. Conventional light gas guns are limited to impact pressures of about 7 Mbar in high-impedance materials. Pulsed radiation sources, such as high-intensity lasers, and pulsed power techniques significantly extend the accessible pressures and are becoming accepted methods for meeting the needs of material models in regimes inaccessible by gas guns. A present limitation of these new approaches is that samples must necessarily be small, typically a few tens of microns in thickness, which severely limits the accuracy of EOS measurements that can be made and also the ability to perform a variety of off-Hugoniot measurements. However, recent advances in z-pinch techniques for high-pressure material response studies provide potential opportunities for achieving accuracies comparable with gas guns because of the significantly larger …

None

Several high explosive formulations have recently been compared in a series of impact tests where samples of each composition were encased in a test fixture designed in flat geometry mocking an HE loaded artillery projectile. The purpose of the ongoing test series is to determine the relative rate of chemical energy release or explosiveness of several standard and research insensitive high explosive (IHE) main charge compositions. The triggering stimulus is the impact of .30 calibre ball bullets fired at normal muzzle velocity.

NMR, UV-vis and isothermal titration calorimetry (ITC) measurements probe different aspects of competing host-guest equilibria as simple alkylammonium guest molecules interact with both the exterior (ion-association) and interior (encapsulation) of the [Ga{sub 4}L{sub 6}]{sup 12-} supramolecular assembly in water. Data obtained by each independent technique measure different components of the host-guest equilibria and only when analyzed together does a complete picture of the solution thermodynamics emerge. Striking differences between the internal and external guest binding are found. External binding is enthalpy driven and mainly due to attractive interactions between the guests and the exterior surface of the assembly while encapsulation is entropy driven as a result of desolvation and release of solvent molecules from the host cavity.

None

Although there are five effective shear moduli for any layered VTI medium, one and only one effective shear modulus of the layered system (namely the uniaxial shear) contains all the dependence of pore fluids on the elastic or poroelastic constants that can be observed in vertically polarized shear waves. Pore fluids can increase the magnitude the shear energy stored in this modulus by an amount that ranges from the smallest to the largest effective shear moduli of the VTI system. But, since there are five shear moduli in play, the overall increase in shear energy due to fluids is reduced by a factor of about 5 in general. We can therefore give definite bounds on the maximum increase of overall shear modulus, being about 20% of the allowed range as liquid is fully substituted for gas. An attendant increase of density (depending on porosity and fluid density) by approximately 5 to 10% decreases the shear wave speed and, thereby, partially offsets the effect of this shear modulus increase. The final result is an increase of shear wave speed on the order of 5 to 10%. This increase is shown to be possible under most favorable circumstances - i.e. when the …

The accuracy and representativeness of flux measurements from a tall tower in a complex landscape was assessed by examining the vertical and sector variability of the ratio of wind speed to momentum flux and the ratio of vertical advective to eddy flux of heat. The 30-60 m ratios were consistent with theoretical predictions which indicate well mixed flux footprints. Some variation with sector was observed that were consistent with upstream roughness. Vertical advection was negligible compared with vertical flux except for a few sectors at night. This implies minor influence from internal boundary layers. Flux accuracy is a function of sector and stability but 30-60 m fluxes were found to be generally representative of the surrounding landscape. This paper will study flux data from a 300 m tower, with 4 levels of instruments, in a complex landscape. The surrounding landscape will be characterized in terms of the variation in the ratio of mean wind speed to momentum flux as a function of height and wind direction. The importance of local advection will be assessed by comparing vertical advection with eddy fluxes for momentum and heat.

A spatial-domain solution to the problem of electromagnetic scattering from a dielectric half-space is outlined. The resulting half-space operators are referred to as Fresnel surface integral operators. When used as preconditioners for nonplanar geometries, the Fresnel operators yield surface Fresnel integral equations (FIEs) which are stable with respect to dielectric constant, discretization, and frequency. Numerical properties of the formulations are discussed.

We discuss a standard model of heavy ion collisions that has emerged both from experimental results of the RHIC program and associated theoretical developments. We comment briefly on the impact of early results of the LHC program on this picture. We consider how this standard model of heavy ion collisions could be solidified or falsified in future experiments at RHIC, the LHC and a future Electro-Ion Collider.

A total of 31 samples from the Long Duration Exposure Facility (LDEF), including materials of aluminum, vanadium, and steel trunnions were analyzed by ultra-low-level gamma spectroscopy. The study quantified particle induced activations of {sup 22}Na, {sup 46}Sc, {sup 51}Cr, {sup 54}Mn, {sup 56}Co, {sup 57}Co, {sup 58}Co, and {sup 60}Co. The samples of trunnion sections exhibited increasing activity toward the outer end of the trunnion and decreasing activity toward its radial center. The trunnion sections did not include end pieces, which have been reported to collect noticeable {sup 7}Be on their leading surfaces. No significant {sup 7}Be was detected in the samples analyzed. The Underground Counting Facility at Savannah River Laboratory (SRL) was used in this work. The facility is 50 ft. underground, constructed with low-background shielding materials, and operated as a clean room. The most sensitive analyses were performed with a 90%-efficient HPGe gamma-ray detector, which is enclosed in a purged active/passive shield. Each sample was counted for one to six days in two orientations to yield more representative average activities for the sample. The non-standard geometries of the LDEF samples prompted the development of a novel calibration method, whereby the efficiency about the samples surfaces (measured with point …

A total of 31 samples from the Long Duration Exposure Facility (LDEF), including materials of aluminum, vanadium, and steel trunnions were analyzed by ultra-low-level gamma spectroscopy. The study quantified particle induced activations of {sup 22}Na, {sup 46}Sc, {sup 51}Cr, {sup 54}Mn, {sup 56}Co, {sup 57}Co, {sup 58}Co, and {sup 60}Co. The samples of trunnion sections exhibited increasing activity toward the outer end of the trunnion and decreasing activity toward its radial center. The trunnion sections did not include end pieces, which have been reported to collect noticeable {sup 7}Be on their leading surfaces. No significant {sup 7}Be was detected in the samples analyzed. The Underground Counting Facility at Savannah River Laboratory (SRL) was used in this work. The facility is 50 ft. underground, constructed with low-background shielding materials, and operated as a clean room. The most sensitive analyses were performed with a 90%-efficient HPGe gamma-ray detector, which is enclosed in a purged active/passive shield. Each sample was counted for one to six days in two orientations to yield more representative average activities for the sample. The non-standard geometries of the LDEF samples prompted the development of a novel calibration method, whereby the efficiency about the samples surfaces (measured with point …