Knowledge of volatile concentrations in magmas are important in the prediction of explosive volcanism, and contribute to the understanding of the carbon dioxide budget of the atmosphere. Some important variables that are controlled by volatiles are: crystallization temperature of phases, composition of liquids minimum, and viscosity. Volatiles are also catalysts for reactions.

The following are included in the well test plan: well test program schedule and order of work; the injection well drilling program details; the production well drilling program details; and long-term (30-day) production testing program details. (MHR)

The basic goal of the Limestone Injection Multistage Burner (LIMB) demonstration is to extend LIMB technology development to a full- scale application on a representative wall-fired utility boiler. The successful retrofit of LIMB to an existing boiler is expected to demonstrate that (a) reductions of 50 percent or greater in SO{sub x} and NO{sub x} emissions can be achieved at a fraction of the cost of add-on FGD systems, (b) boiler reliability, operability, and steam production can be maintained at levels existing prior to LIMB retrofit, and (c) technical difficulties attributable to LIMB operation, such as additional slagging and fouling, changes in ash disposal requirements, and an increased particulate load, can be resolved in a cost-effective manner. The primary fuel to be used will be an Ohio bituminous coal having a nominal sulfur content of 3 percent or greater.

A multiple-reflection optical cell for Raman or fluorescence gas analysis consists of two spherical mirrors positioned transverse to a multiple-pass laser cell in a confronting plane-parallel alignment. The two mirrors are of equal diameter but possess different radii of curvature. The spacing between the mirrors is uniform and less than half of the radius of curvature of either mirror. The mirror of greater curvature possesses a small circular portal in its center which is the effective point source for conventional Fl double lens collection optics of a monochromator-detection system. Gas to be analyzed is flowed into the cell and irradiated by a multiply-reflected composite laser beam centered between the mirrors of the cell. Raman or fluorescence radiation originating from a large volume within the cell is: (1) collected via multiple reflections with the cell mirrors; (2) partially collimated; and (3) directed through the cell portal in a geometric array compatible with Fl collection optics.

In neutron dosimetry, calculations enable one to predict the response of a proposed dosimeter before effort is expended to design and fabricate the neutron instrument or dosimeter. The nature of these calculations requires the use of computer programs that implement mathematical models representing the transport of radiation through attenuating media. Numerical, and in some cases analytical, solutions of these models can be obtained by one of several calculational techniques. All of these techniques are either approximate solutions to the well-known Boltzmann equation or are based on kernels obtained from solutions to the equation. The Boltzmann equation is a precise mathematical description of neutron behavior in terms of position, energy, direction, and time. The solution of the transport equation represents the average value of the particle flux density. Integral forms of the transport equation are generally regarded as the formal basis for the Monte Carlo method, the results of which can in principle be made to approach the exact solution. This paper focuses on the Monte Carlo technique.

The Sunkist Citrus Plant in Ontario, California, processes about 6 million pounds of citrus fruit per day to make products which include frozen concentrated juice; chilled, pasteurized, natural strength juice; molasses from peel; dried meal from peel; pectin; citrus oil; and bioflavonoids. The energy intensive operations at the plant include concentration, drying, and refrigeration. The objective of the two-year two-phase project is to identify an economically viable alternative to the existing method of meeting energy requirements. Progress on the technical work of Phase I is reported. The following are summarized: requirements (energy price projection, atmospheric emission requirements, citrus juice quality constraints, economic evaluations); characterization (basic citrus processing operations, energy consumption and fruit processed vs time, identification and measurement of energy uses, energy balance for a typical citrus juice evaporator); and thermodynamic analysis (heat pump model, thermal evaporator, and co-generation model).

We have investigated the role of an isomeric state and its coupling to the ground state (g.s.) via photons and neutron inelastic scattering in a stellar environment by making detailed photonuclear and neutron cross-section calculations for /sup 176/Lu and /sup 210/Bi. In the case of /sup 176/Lu, the g.s. would function as an excellent galactic slow- (s-) process chronometer were it not for the 3.7-h isomer at 123 keV. Our calculations predicted much larger photon cross sections for production of the isomer, as well as a lower threshold, than had been assumed based on earlier measurements. These two factors combine to indicate that an enormous correction, a factor of 10/sup 7/, must be applied to shorten the current estimate of the half-life against photoexcitation of /sup 176/Lu as a function of temperature. This severely limits the use of /sup 176/Lu as a stellar chronometer and indicates a significantly lower temperature at which the two states reach thermal equilibrium. For /sup 210/Bi, our preliminary calculations of the production and destruction of the 3 /times/ 10/sup 6/ y isomeric state by neutrons and photons suggest that the /sup 210/Bi isomer may not be destroyed by photons as rapidly as assumed in certain …

The failure mode analysis for any cryogenic system includes the effects of a large liquid spill due to vessel rupture or overfilling. The Oxygen Deficiency Hazard (ODH) analysis for this event is a strong function of the estimated heat flux entering the spilled liquid. A common method for estimating the heat flux is to treat the surface on which the liquid spills as a semi-infinite solid. This note addresses the effect of linearizing the temperature profile in this form of analysis, and shows it to cause the calculated flux to be underestimated by more than a factor of two. 3 refs., 2 figs.

An analytical procedure was developed to estimate the cooldown time between pulses of the Compact Ignition Tokamak (CIT) utilizing liquid nitrogen. Fairly good agreement was obtained between the analysis results and those measured in the early fusion experimental devices. The cooldown time between pulses in the CIT is controlled by the energy disposition in the inner leg of the TF coil. A cooldown time of less than one hour is feasible for the CIT if fins are used in the cooling channels. An R and D experimental program is proposed to determine the actual cooldown time between pulses since this would be considered an issue in the conceptual design of the CIT.

Data from e/sup +/e/sup -/ annihilations at 29 GeV have been used to measure the production and fragmentation of eta mesons. The signal is observed in the eta ..-->.. ..gamma gamma.. decay channel. The fragmentation function for p/sub eta/ > 1.5 GeV/c agrees well with the shapes predicted by both the Lund and Webber models. However, the mean multiplicity is measured to be < n/sub eta/ > = 0.37 +- 0.08 eta mesons per hadronic annihilation event, which is significantly lower than the values predicted by either model. 6 refs., 2 figs., 1 tab.

Results pertaining to the recently modified beam-injection arrangement in the central cell of TMX-U are presented here. These modifications followed our observation that beam atoms injected perpendicular to the magnetic axis between the first two magnet-coil gaps give rise to trapped ions with midplane pitch angles lying in the intervals 68/sup 0/ < theta < 78/sup 0/ and 59/sup 0/ < theta < 65/sup 0/. These pitch-angle intervals are similar in value to the earlier arrangement of beams injected at the midplane at pitch angles of 58 and 70/sup 0/. Normal injection at an off-midplane position has two advantages when compared with off-normal injection at the midplane. First, the unattenuated beam can be dumped in the first-injector region rather than in the plasma region. Second, the beams can be oriented with their long dimension horizontal rather than vertical. The first point al

The report from Lawrence Livermore National Laboratory, which covers the period from October 1981 to September 1982, is divided into three major sections. The first section, progress reports, includes studies in areas of industrial hygiene, instrument development, environmental protection, radiation protection and fire safety. The second section, technical notes, contains reports on interesting activities of a more limited scope. The third section lists recent publications. (JMT)

The report consists of viewgraphs. Topics covered are (1) basic ripple processes, (2) simulations of combined processes, (3) modeling issues, (4) new physics problems, and (5) consequences for ETR/ITER. (WRF)

The interferometer and viewing optics that are the main optical components of an Automated Surface Mapping system (ASM) used to characterize the surface topography and the wall thickness uniformity of opaque and transparent spherical shells is described. To characterize surface finish or wall thickness of spherical shells with an accuracy of 10 nm and a resolution of 1 ..mu..m the differential phase shift between two beams of orthogonal polarizations is measured, before and after the probe beam has interacted with the test object.

A heat-exchanging fireplace was installed in a 2000 square foot home and the standard air distribution equipment was ducted directly to the forced-air heating system of the home. The standard air distribution equipment for the fireplace included two squirrel-cage blowers which were connected to a thermostat, allowing a choice of temperature ranges; and a snap disc thermostat was used to disconnect the blowers in order to avoid blowing cold air after the fire died out. Arranged in this manner, one is able to set the regular home thermostat a few degrees lower than the fireplace thermostat, and this will allow the regular heating system to turn on after the fire has gone out in the fireplace. Energy consumption in both the fireplace and the conventional heating system was monitored throughout a heating season and then compared with past heating seasons when only a conventional heating system was used.

The dissolution of plutonium dioxide in nitirc acid (HNO/sub 3/) at high hydrofluoric acid (HF) concentrations has been investigated. Dissolution rate curves were obtained using 12M HNO/sub 3/ and HF at concentrations varying from 0.05 to 1.0 molar. The dissolution rate increased with HF concentration up to 0.2M and then decreased at higher concentrations. There was very little plutonium dissolved at 0.7 and 1.0M HF because of the formation of insoluble PuF/sub 4/. Various oxidizing agents were added to 12M HNO/sub 3/-1M HF dissolvent to oxidize Pu(IV) to Pu(VI) and prevent the formation of PuF/sub 4/. Ceric (Ce(IV)) and silver (Ag(II)) ions were the most effective in dissolving PuO/sub 2/. Although these two oxidants greatly increased the dissolution rate, the rates were not as rapid as those obtained with 12M HNO/sub 3/-0.2M HF.

This report describes calculations and analysis performed in an attempt to provide a new estimate for the yield of the Hiroshima weapon. Newly discovered meteorological data was adapted for use in one- and two-dimensional hydrodynamic codes, and a series of calculations was then run for different values of yield. The objective was to determine what yield produced an overpressure record which could best be correlated with an actual trace measured at a parachute-dropped canister. Altitude of the bomb and canister-carrying aircraft at drop time was also a variable parameter. The analysis provides an estimate of 16.6 + 0.3 kt for the yield of the Hiroshima weapon. A drop altitude of near 35,500 feet is shown to be consistent with the signal time-of-arrival. This yield value is within the range of other estimates, but the drop altitude is higher than that previously assumed to be reasonable.

In the summer of 1988, the Department of Nuclear Engineering (NE) at the University of Tennessee (UT) in Knoxville was selected to carry out a research program in Enhancing the Operation of Nuclear Power plants through the use of Artificial Intelligence, This program is sponsored by the Department of Energy's Office of Energy Research under 10CFR605 for Nuclear Engineering Research. The objective of the research is to advance the state-of-the-art of nuclear power plant control, safety, management, and instrumentation systems through the use of artificial intelligence (AI) techniques, including both expert systems and neural networks. The emphasis will be placed on methods that can be implemented on a rapid or real-time basis. A second, but equally important, objective is to build a broadly based critical mass of expertise in the artificial intelligence, field that can be brought to bear on the technology of nuclear power plants. Both of these goals are being met. This overview and the attached technical reports describe the work that is being carried out. Although in some cases, the scope of the work differs somewhat from the specific tasks described in the original proposal, all activities are clearly within the overall scope of the contract.

Over the years the study of the confinement of high temperature plasma in magnetic mirror systems has presented researchers with many unusual physics problems. Many of these issues are by now understood theoretically and documented experimentally. With the advent of the tandem mirror idea, some new issues have emerged and are now under intensive study. These include: (1) the generation and control of ambipolar confining potentials and their effect on axial confinement and, (2) the combined influence of nonaxisymmetric magnetic fields (used to ensure MHD stability) and electric magnetic particle drifts on radial transport. Physics considerations associated with these two categories of issues will be reviewed, including concepts for the control of radial transport, under study or proposed.

Plutonium-fueled radioisotopic heat sources find application in a spectrum of space, terrestrial, and underseas applications to generate electrical power by thermoelectric or dynamic-cycle conversion. Such systems under postulated accident conditions could release radioactivity into the environment resulting in risks to the general population. The released radioactivity could be dispersed into various environmental media, such as air, soil, and water and interact with people through various exposure pathways leading to inhalation, ingestion, and external radiological doses and associated health effects. The authors developed short-term exposure (RISK II) and long-term exposure (RISK III) models for use in safety risk assessments of space missions utilizing plutonium-fueled electric power systems. To effectively use these models in risk assessments, representative input values must be selected for a spectrum of environmental transfer parameters that characterize the behavior of plutonium in the environment. The selection of appropriate transfer parameters to be used in a given analysis will depend on the accident scenarios to be modeled and the terrestrial and aquatic environments to be encountered. The authors reviewed the availability of plutonium in the environment. This report summarizes the research programs presently being conducted at six Department of Energy Laboratories and makes recommendations on areas where further research …

This report summarizes the results of an industry survey made during the summer of 1983. The survey was initiated in order to develop an information base on advanced engines that could be used in the solar thermal dish-electric program. Questionnaires inviting responses were sent to 39 companies known to manufacture or integrate externally heated engines. Follow-up telephone communication ensured uniformity of response.

The Hazards Control Department of Lawrence Livermore National Laboratory maintains a Standards and Calibration Laboratory that includes three neutron sources (two /sup 252/Cf and one /sup 238/PuBe that can be positioned pneumatically for irradiations. Ten moderators exist to modify the neutron energy spectra produced by these sources. The thicknesses and materials of these moderators are: 25-cm water; 5-, 10-, 15-, and 25-cm heavy water; 20-cm aluminum; and 2-, 5-, 10-, and 15-cm polyethylene. We used a multisphere spectrometer to measure the neutron spectra at 2 m from both the PuBe source and the smaller Cf source, with the sources bare, and in all of the moderators. These data were reduced in 25 energy groups ranging from 0.25 eV to 16 MeV. Except for the 15-m polyethylene moderator, we also made measurements using a liquid-scintillator fast-neutron spectrometer. These data were reduced in 0.1-MeV increments from 0.5 to 12.5 MeV. Spectra from the measurements and from independent calculations are presented in tabular and graphic form. Dosimetric values, calculated from both the measured and calculated spectra, are also presented.

A simple graphical method has been developed to undertake technical design trade-off studies for individual parabolic dish modules comprising a two-axis tracking parabolic dish with a cavity receiver and power conversion assembly at the focal point. The results of these technical studies can then be used in performing the techno-economic analyses required for determining appropriate subsystem sizing. Selected graphs that characterize the performance of subsystems within the module have been arranged in the form of a nomogram that would enable an investigator to carry out several design trade-off studies. Key performance parameters encompassed in the nomogram include receiver losses, intercept factor, engine rating, and engine efficiency. Design and operation parameters such as concentrator size, receiver type (open or windowed aperture), receiver aperture size, operating temperature of the receiver and engine, engine partial load characteristics, concentrator slope error, and the type of reflector surface, are also included in the graphical solution. Cost considerations are not included. The nomogram has been used to perform trade-off studies that have provided a basis for determining requirements for a single concentrator that could perform satisfactorily with either the selected Stirling or Brayton engine. This activity is summarized to illustrate the usage of the nomogram. Additionally, …

A new electric gun system was constructed for use in high-pressure EOS studies. The system is powered by a 100 kV, 15.6 ..mu..F capacitor bank. At 100 kV charging voltage the system inductance is 23 nH. This system has driven 0.3 mm-thick Kapton projectiles to > 20 km/s and 0.3 mm Kapton/30 ..mu..m Ta projectiles to approx. 10 km/s. Projectile velocity is modeled phenomenlogically by an electrical Gurney model.