The following document describes the usage and results of sending pulsed beams of electrically charged particles with electrically wide range of pulse lengths and pulse repetition rates.

The development of high-energy charged particle accelerators such as the Bevatron and of improved nuclear-event detection devices such as the Berkeley 72-in. hydrogen bubble chamber has greatly increased the need for high-speed data reduction of nuclear events. Full exploitation of the potential of the 72-in. bubble chamber demands a very high-speed analysis system. This paper describes an approach to such a system.

It has been observed that energetic gaseous ions mark their region of impingement on certain metals in color. Under identical conditions of bombardment, multicharged ions of the same gas mark their impact areas with different colors. The colors are sensitive to the type and energy of the ion as well as to the metal bombarded. These colors may result from reflections from thin films formed by reactions at the target. Because the colors indicate that thicker films are produced with increased ion energy, ion penetration depth as predicted by theory is compared with the depth indicated by the colors observed.

Tory 11-A, the first experimental reactor in the Pluto nuclear ramjet program, will be tested in late 1960 at the Nevada Test Site of the Atomic Energy Commission. The fundamental objective of Tory II-A is to demonstrate that a high power density, high-temperature, air-cooled reactor can be successfully designed, constructed, and operated. This application places requirements on the reactor control system which are considerably more stringent than those found in previous reactor systems, both from the standpoint of radiation environment and system performance. To fulfill the system requirements a high-performance reactor control system has been designed and built; control actuation hardware has been developed which can withstand the high-radiation environment of Tory LI-A. This actuation system features radiation-tolerant electrohydraulic components: actuators, servo-valves, solenoid valves, feedback transducers, accumulators and associated hydraulic components. To provide high reliability against undesired shutdowns while carrying out high power level transients, the Tory 11-A control philosophy includes a new concept in reactor safety: reliance on a nonlocking, fast-reset safety system during accident situations. The fast-reset system acts so as to hold the programmed power level rather than initiating an irreversible "scram" action. A reactor "scram", if tolerated, could produce thermal shocks which would seriously damage the …

Under the stimulus of electronic materials development - particularly thin-film studies - and the need for space environmental simulation chambers, a very rapid increase in the availability of industrial-sized vacuum components and systems operable in the ultrahigh vacuum range has taken place in the last three years. It is the purpose of this paper to explore the design considerations of ultrahigh vacuum systems for metallurgical applications.

The Astron, a thermo-nuclear fusion research machine, requires the injection of high-energy electron at 5 MEV emery level +- 1/2 %, 200 amperes, 60 pulses per second, 0.3 usec pulse width. The accelerator will work by the induction principle with approximately 500 magnetic cores, each 1/2 inch thick lined up on centers. Each core will be pulsed by a single primary turn and the electrons forming the secondary will experience a voltage acceleration equivalent to the primary voltage upon passing by each core. The coupling in this arrangement has been tested and it is very nearly unity.

The most important component required for the Astron experimental facility is a high energy, high current, pulsed electron accelerator. A thin cylindrical layer of high energy electrons trapped within an axially symmetric magnetic field is the key feature of the Astron thermonuclear device. The trapping magnetic field is constant in time. Therefore, it is not possible to inject electrons and trap the electrons in this field unless during the injection phase a part of the electron energy is absorbed by some friction process. This is accomplished by means of eddy currents generated on suitable passive circuits by the current of the injected electron bunch. This method has ben described elsewhere. However, in order to achieve an effective loss mechanism the current of the injected electron beam must be over one hundred amps. Such high current beams are difficult to handle except if the electron energy is high enough so that the electrostatic repulsive force is compensated to great extent by attractive magnetive forces. Hence the electron energy required is 5 Mev or higher. Other requirements on the electron layer yield the same result.

Abstract: "Microwaves have been used for several years at Lawrence Radiation Laboratory to study conditions in the magnetically contained plasmas of controlled fusion research. There are two basic microwave techniques. One gives information on electron density and distribution in the plasma, the other provides data on electron temperature. This paper briefly summarizes the established techniques, discusses engineering requirements and limitations, and describes some further applications of microwaves presently being considered."

Introduction. The von Neumann stability criterion is used to analyze the stability of three types of difference schemes for partial differential equations. It is shown that, contrary to the usual rule of thumb, there exist symmetric implicit schemes for a class of equations which are unstable for every mesh-ratio but that this cannot occur if (a) there are fewer than three "space" variables or (b) the difference expression is used to approximate the mixed derivative.

Individual Samarkand wildtype D. melanogaster males were permitted to choose between either two white-eyed or two red-eyed females or between a red-eyed and a white-eyed female. Observations of the flies were made over a period of about two hours and premating periods, intermating periods and the durations of copulations were recorded.

To properly assess the "sensitivity" of explosives systems under impact conditions we must obtain detailed information on these mechanisms by which explosives are ignited by impact. It is necessary to know which impact conditions represent the greatest hazard to explosive materials, as well as to know for a given impact condition the relative responses of explosives of interest. I should like to describe to you a program sponsored jointly by the Department of Defense and the Atomic Energy Commission to attain this type of information. A wide variety of impact experiments have been conducted using geometrical arrangements of explosive, plastic, and metal which are relatively simple compared to complete ordnance systems. All of these tests have employed billets of explosive fabricated by standard production techniques, and the billets have been sufficiently large that ignition, once started, has something of the same opportunity to grow or decay as in full scale ordnance assemblies. From these relatively simple tests there has accrued much new useful information on the behavior of explosives under impact. With this new information providing a base from which to work, it is hoped that theoretical calculations on impact phenomena will in the future make a bigger contribution to …

In the course of modern physics research, the need frequently arises for storage of large quantities of electrical energy which can be periodically discharged at high peak power into a load. Until recently, the homopolar machine has been an intriguing device having considerable academic interest but little practical value. In recent years, successful machines have been developed to utilize liquid-metal brush systems. The liquid-metal brush overcomes all the problems associated with current collection power loss, frictional loss, and limiting peripheral velocity. Consequently, these machines are now worth serious consideration where high-current dc generation is required. The main purpose in setting up a homopolar generator test program was to establish the limits to which an essentially standard commercially available generator of this type could be pushed.

The statistical behavior of measured track quantities, gap density, gap length coefficient, and lacunarity is studied. The transformations which give the expectation values of track quantities on inclined tracks are then found.