Report discussing an adapter which uses three Tuckerman optical strain gages to measure the displacement of the three vortices of an equilateral triangle along lines 120 degrees apart. These displacements are substituted in well-known equations in order to compute the magnitude and direction of the principal strains. Tests of the adaptor indicate that principal strains over a gage length of 1.42 inch may be measured with a systematic error not exceeding 4 percent and a mean observational error of the order of + or minus 0.000006. The maximum observed error in strain was of the order of 0.00006. The directions of principal strains for unidirectional stress were measured with the adaptor with an average error of the order of 1 degree.

Report presenting an investigation of the characteristics of partial-span spoilers located at 0.75 of the chord on an NACA 66-series tapered wing, especially at high speeds. The effect of small spoiler projections was found to increase with an increase in speed until the critical Mach number was exceeded.

Report presenting theoretical pressure distributions and experimental aerodynamic characteristics at low speeds for a group of NACA four-digit series airfoil sections. Results regarding lift, drag, and pitching moment are provided.

From Introduction: "Recent investigations have indicated several wing plan forms, wing sections, and wing-body-tail combinations suitable for flight at supersonic speeds. One such lifting surface, a thin, sharp-edged without sweep of aspect ratio 4 and taper ratio 0.5, has been the subject of an investigation in the Ames 12-foot pressure wind tunnel. The aim of the investigation was to determine the aerodynamic characteristics of such a wing plan form throughout the range of subsonic Mach numbers up to 0.94."

From Introduction: "Although the aerodynamic characteristics of the components of such configurations may be well known, the mutual interference resulting from combining the wings, as well as the wings and body, may be so great that is desirable to study the aerodynamic properties of the complete configurations. Two methods of handling this problem are presented in this report. The first method is essentially an extension of the theory for slender wing-body combinations of reference 1 to determine the load distribution, forces, and moments exerted on slender cruciform-wing and body combinations inclined simultaneously at small angles in pitch and yaw. "

Report presenting tests made in the LMAL 16-foot high-speed tunnel to determine the aerodynamic characteristics of a 1000-pound AN-M-65-AZON radio-controlled bomb at a Mach number range of 0.2 to 0.6. Over the Mach number range, the hinge-moment coefficients, yawing-moment coefficients, and lateral-force coefficients exhibited no important changes with increasing speed.

From Introduction: "An investigation of the power-plant installation of a single-engine torpedo-bomber-type airplane has been conducted in the NACA Cleveland altitude wind tunnel at the request of the Bureau of Aeronautics, Navy Department. A similar investigation was previously conducted on a three-tenths scale mock-up of the forward portion of the fuselage of this airplane in the Langley 20-foot tunnel. (See reference 1)."

This short analysis may be useful in determining the real tactical possibilities of "glider trains" and in adopting the course to be followed in possible studies of these questions. In this analysis most prominent are: (a) the power required for the train in level flight; (b) its speed; (c) climb; and (d) the type of airplane best suited for towing as well as design requirements for transport gliders.

"In the present paper, under the same lineaeizing assumptions as are made in the derivation in reference 1 but with the explicit consideration and simplification of the form of the wake extending from the rear of the airfoil, the methods of Theodorsen (reference 2) have been extended to obtain the forces on the airfoil not only at a fixed angle of attack but also in arbitrary motion" (p. 1).

Report is a brief summary of investigations on symmetrical and cambered airfoils in the DVL high-speed tunnel. Some information on the effects of low aspect ratio are also included.

"An altitude-test-chamber investigation was conducted to determine the operational and performance characteristics of a McDonnell afterburner with a fixed-area exhaust nozzle on a J34 engine. At rated engine speed, the altitude limit, as determined by combustion blow-out, occurred as a band of unstable operation of about 6000-foot altitude in width with minimum altitude limits from 31,000 feet at a simulated flight Mach number of 0.40 to about 45,500 feet at a simulated flight Mach number of 1.00. Considerable difficulty was experienced in attempting to establish or maintain balanced-cycle engine operation at altitudes above 36,000 feet" (p. 1).

From Introduction: "Thrust augmentation of an axial-flow-type turbojet engine by burning fuel in the tail pipe is discussed in references 1 to 3. Thrust augmentation of the same turbojet engine by water injection at the compressor inlet is reported in reference 4."

From Summary: "This paper describes a method for the determination of drop size and free water in clouds, based on the interpretation of an artificially created rainbow. Details of the design and operation of an optical instrument employing this method are presented."

From Introduction: "In references 1, 2, and 3, flight measurements of the performance of a conventional, single-rotor helicopter equipped with its production fabric-covered main rotor blades are presented."

"The performance of the turbine component of an NACA research jet engine was investigated with cold air. The interaction and the matching of the turbine with the NACA eight-stage compressor were computed with the combination considered as a jet engine. The over-all performance of the engine was then determined. The internal aerodynamics were studied to the extent of investigating the performance of the first stator ring and its influence on the turbine performance" (p. 397).

"In order to understand the operation and the interaction of jet-engine components during engine operation and to determine how component characteristics may be used to compute engine performance, a method to analyze and to estimate performance of such engines was devised and applied to the study of the characteristics of a research turbojet engine built for this investigation. An attempt was made to correlate turbine performance obtained from engine experiments with that obtained by the simpler procedure of separately calibrating the turbine with cold air as a driving fluid in order to investigate the applicability of component calibration. The system of analysis was also applied to prediction of the engine and component performance with assumed modifications of the burner and bearing characteristics, to prediction of component and engine operation during engine acceleration, and to estimates of the performance of the engine and the components when the exhaust gas was used to drive a power turbine" (p. 1).

"This report is the second phase of a broad program of study of the transient motions of helicopters in autorotative flight. The first phase (reference 1) dealt with the steady-state condition of autorotative vertical descent. This report is concerned with the the transition from the steady condition of hovering to the steady autorotative descent" (p. 1).

From Introduction: "In the present paper, the variation of effective gust velocity in convective-type clouds with altitude is investigated. Data obtained during 1941 and 1942 at altitudes up to 34,000 feet and data obtained more recently from the Thunderstorm Project (reference 5) at altitudes up to 26,000 feet are utilized for this purpose. Consideration is given in analyzing the results both to data for the range

"This report is the result of the first part of a broad program to analyze the transient motions of a helicopter, which occur in the various phases of flight following power failure" (p. 1).

From Introduction: "The present paper covers step 1 of the outlined investigation, includes methods of computing the variation of wing and tail loads, and gives numerical results of the application of the theory to the BT-9B airplane. Finally, theoretical formulas are developed and charts are given for computing the maximum increments of wing load, the down-tail load, and the up-tail load following a given elevator displacement."

"Requirements of an automatic engine control, as affected by engine characteristics, have been analyzed for a direct-coupled turbojet engine. Control parameters for various conditions of engine operation are discussed. A hypothetical engine control is presented to illustrate the use of these parameters. An adjustable speed governor was found to offer a desirable method of over-all engine control. The selection of a minimum value of fuel flow was found to offer a means of preventing unstable burner operation during steady-state operation" (p. 1).

Analysis was made to determine characteristics required of a balancing-tab system for ailerons in order to reduce aileron stick forces to any desired magnitude. Series of calculations based on section data were made to determine balancing-tab systems of various chord tabs and ailerons that will give, for a particular airplane, zero rate of aileron hinge moment with aileron deflection and yet will produce same maximum rate of roll as a plain unbalanced 15-percent chord aileron of same span. Effects of rolling velocity and of forces in tab link on aileron hinge moments have been included.

Note presenting an investigation conducted to determine the applicability of statistical methods as an approach to the evaluation of materials for use in gas turbines by determining the frequency distribution of time until failure of gas-turbine blades. Two wheels, each incorporating 142 inserted blades of a cast cobalt-base heat-resistant alloy, were tested. The results indicated that the time for first failure may not generally be taken as an accurate indication of the performance of the average blade.

Report presenting a series of tests to determine the bearing yield and ultimate strengths of samples of 1/4- and 2-inch-thick plate of aluminum alloy 24S-T and to establish nominal ratios of bearing-to-tensile properties for the commercial range of plate thicknesses. Results regarding individual bearing testing, ratios of average bearing to tensile properties, and ratios of bearing yield strength to tensile yield strength are provided.