Circular presenting a description of the light airplane SM-1, which was designed by W. S. Shackleton and Lee Murray. Information regarding the design and flight characteristics and some photographs of the airplane are provided.

Circular presenting a description of the Avro Trainer airplane, which is primarily intended for pilots in training and is designed to be easy to use, including large, comfortable cockpits, good view, effective windshields, and wide track. Details of the design, flight characteristics, drawings, and photographs are provided.

"A quantitative criterion of merit has been needed to assist airplane designers to incorporate satisfactory spinning characteristics into new designs. An approximate empirical criterion, based on the projected side area and the mass distribution of the airplane, has been formulated in a recent British report. In the present paper, the British results have been analyzed and applied to American designs. A simpler design criterion based solely on the type and the dimensions of the tail, has been developed: it is useful in a rapid estimation of whether a new design is likely to comply with the minimum requirements for safety in spinning" (p. 1).

Circular describing the Dewoitine D 33 commercial airplane, which is a low-wing cantilever monoplane. Details of the wing, fuel tanks, fuselage, landing gear, controls, engine, characteristics, drawings, and photographs are provided.

Circular presenting a description of the Baynes Bee, which is a light two-seat high-wing monoplane. Details of its unique qualities, design, components, flying qualities, drawings, and photographs are provided.

Circular presenting a description of the Bernard 82, which is a scaled-up version of the 80 G.R.; they have similar designs but the 82 has greater span and wing area, deeper chord, higher fuselage, and a thicker wing for the bombs. A description of some flight tests and characteristics is also provided.

"This investigation was conducted to study the practicability of employing heat as a means of preventing the formation of ice on airplane wings. The report relates essentially to technical problems regarding the extraction of heat from the exhaust gases and its proper distribution over the exposed surfaces. In this connection a separate study has been made to determine the variation of the coefficient of heat transmission along the chord of a Clark Y airfoil. Experiments on ice prevention both in the laboratory and in flight show conclusively that it is necessary to heat only the front portion of the wing surface to effect complete prevention" (p. 3).

This investigation attempts to surpass the boundaries of pure mathematical interest in that it possesses as an example, a flow investigation in a multiply-connected region. Then the results appear to be carried out by means of an appropriate conformal representation of the region around two chosen closed curves. Thus we have the basis of an exact plane theory of the biplane.

This report details the methods of construction employed by the Gloster Company in their fabrication of metal aircraft parts. Ribs, spars, wings, and metal treatments to prevent oxidation are all discussed.

From Summary: "A theory is developed for the airfoil of finite span at supersonic speed analogous to the Prandtl airfoil theory of 1918-1919 for incompressible flow. In addition to the profile and induced drags, account must be taken at supersonic flow of still another drag, namely, the wave drag, which is independent of the wing aspect ratio. Both wave and induced drags are proportional to the square of the lift and depend on the Mach number, that is, the ratio of flight to sound speed. In general, in the case of supersonic flow, the drag-lift ratio is considerably less favorable than is the case for incompressible flow."

The theory of landing impact is briefly stated and the applicability of a previously suggested formula is extended. Theoretical considerations regarding impact measurements on models and actual seaplanes are followed by a brief description of the instruments used in actual flight tests. The report contains a description of the strength conditions and deals exhaustively with force measurements on the float gear of an "HE 9a" with flat-bottom and with V-bottom floats. The experimental data are given and compared with the theoretical results.

This report presents the results and a recounting of the new technological developments that were developed for the 11th Rhon Soaring Contest.

The appearance of expressed discontinuity layers in the free atmosphere, where a warm air mass flows over a cold mass without perceptible intermingling forms the basis of the present report. In these experiments an air stream is to be blown between a water-cooled and a vapor-heated plate. According to what preceded it is anticipated that the exchange will be enhanced.

"At the suggestion of Professor Betz, the following device was tested with the object of reducing the autorotational speed of airplane wings. The model of a normal wing with the Gottigen profile 420, 1 meter span and 0.2 meter chord was provided with a pair of symmetrical slots on the suction side, connected with each other inside the wing. The arrangement of the testing equipment and models are given and the effect of the slots can be seen in the experimental curves that are included" (p. 1).

"Recent developments in airfoil-testing methods and fundamental air-flow investigations, as applied to airfoils, are discussed. Preliminary test results, obtained under conditions relatively free from stream turbulence and other disturbances, are presented. Suitable airfoils and airfoil-design principles were developed to take advantage of the unusually extensive laminar boundary layers that may be maintained under the improved testing conditions" (p. 1).

"Tables of stiffness and carry-over factor are presented for members in which the cross section and axial load do not vary along the length of the member. These tables are of use in solving problems in the stability of structural members under axial load as well as in application of the Cross method of moment distribution when the effects of axial load in the members are considered. The interval between successive values of the argument is small enough to make interpolation unnecessary in engineering calculations" (p. 1).

Flight tests were made to demonstrate the particularity of employing fixed tabs in conjunction with a suitably designed differential linkage to reduce the force required to operate ailerons. The tests showed the system to be practicable with tabs of the inset type. The relative ineffectiveness of attached tabs for changing the aileron floating angle rendered them unsuitable. Experience gained in the investigation has indicated that the use of the system is limited to maximum deflections of one aileron relative to the other of less than 30 degrees and that the differential linkage should always be designed on the basis of the highest probable floating angle.

"The N.A.C.A. combustion apparatus was altered to operate as a fuel-injection, spark-ignition engine, and a preliminary study was made of the combustion of gasoline-air mixtures at various air-fuel ratios. Air-fuel ratios ranging from 10 to 21.6 were investigated. Records from an optical indicator and films from a high-speed motion-picture camera were the chief sources of data. Schlieren photography was used for an additional study" (p. 1).

Oxygen regulators are used in aircraft to regulate automatically the flow of oxygen to the pilot from a cylinder at pressures ranging up to 150 atmospheres. The instruments are adjusted to open at an altitude of about 15,000 ft. and thereafter to deliver oxygen at a rate which increases with the altitude. The instruments are tested to determine the rate of flow of oxygen delivered at various altitudes and to detect any mechanical defects which may exist.

Report presenting an examination of the thermodynamics of combustion in the Otto cycle engine, including the effects of turbulence and some of the possible causes of detonation within an engine.

Ignition-lag data have been obtained for seven fuels injected into heated, compressed air under conditions simulating those in a compression-ignition engine. The results of the bomb tests have been compared with similar engine data, and the differences between the two sets of results are explained in terms of the response of each fuel to variations in air density and temperature.

"An investigation was made in the N.A.C.A. ice tunnel at air temperatures from 20 degrees to 28 degrees Fahrenheit and at a velocity of 80 miles per hour to determine whether ice formations on a model wing could be prevented by the use of the heat from the engine-exhaust gas. Various spanwise duct systems were tested in a 6-foot-chord N.A.C.A. 23012 wing model. The formation of ice over the entire wing chord was prevented by the direct heating of the forward 10 percent of the wing by hot air, which was passed through leading-edge ducts" (p. 1).

"An investigation has been made in the N.A.C.A. 7- by 10-foot wind tunnel of a large-chord N.A.C.A. 23012 airfoil with several arrangements of a 40-percent-chord slotted flap to determine the section aerodynamic characteristics of the airfoil as affected by slot shape, flap location, and flap deflection. The flap positions for maximum lift, the polar for arrangements considered favorable for take-off and climb, and the complete section aerodynamic characteristics for selected optimum arrangements were determined. A discussion is given of the relative merits of the various arrangements" (p. 1).

This report presents test results obtained during an investigation of the performance of a single-cylinder, high-speed, compression-ignition test engine when using multiple-orifice fuel-injection valve nozzles in which the number and the direction of the orifices were varied independently.