From Introduction: "The airfoil sections tested, which differ only in thickness ratio, were the NACA 64-006, 64-008, 64-010, and 641-012. Lift, drag, and pitching-moment data were obtained for Mach numbers of 0.3 to that for tunnel choke at angles of attack of -2^o to 31^o. The results of this investigation are reported herein."

"During the flight investigation of the X-1 airplane the hinge moments of the elevator and aileron control surfaces have been measured over a Mach number range extending to above 1.0. The results of these measurements are presented in this paper" (p. 2).

"Altitude performance of a YJ71-A-7 turbojet engine, with afterburner inoperative, was determined in the NACA Lewis altitude wind tunnel over a wide range of flight conditions. Engine speed and exhaust-nozzle area were controlled independently during this investigation. The variation of corrected values of air flow, net thrust, and fuel flow with corrected engine speed was not defined by a single curve with changes in altitude at given flight Mach number" (p. 1).

From Introduction: "In response to the ever-increasing need for high thrust augmentation, an investigation was conducted that had as its primary objective the attainment of maximum exhaust-gas temperature and thrust (ref. 1). The investigation reported herein was therefore conducted to ascertain the operational limits of the most promising high-temperature afterburner design of reference 1 and to determine its performance over a wind range of flight conditions."

Report discussing the performance of a 20-inch-diameter ram-jet engine at Mach number 3.0 over a range of simulated altitudes from 60,500 to 66,500 feet. Information about the maximum combustor efficiency, range of exhaust-nozzle total pressures, lean blow-out, diffuser total-pressure recovery, and internal thrust coefficient is provided.

Report presenting an investigation of the performance of a 20-inch-diameter ram-jet engine at Mach number 3.0 in a free-jet facility over a range of simulated altitudes. Results regarding the diffuser characteristics, combustor performance, thrust output, and operational characteristics are provided.

From Introduction: "This report extends the short-bearing pressure-distribution function of Michell and Cardullo to give equations for the various bearing characteristics. This short-bearing approximation makes available formulas relating eccentricity ratio to applied load, attitude angle, angular position of peak film pressure to unit pressure on projected area."

From Introduction: "This paper will treat the problem in the suggested manner, beginning with the development of a suitable boundary condition to represent mathematically a homogeneous boundary which has the same flow characteristics, at a point in the flow sufficiently removed from the boundary as the actual physical boundary of alternate open and closed portions of the wall. Numerical results will be presented for circular tunnels with uniformly distributed around the circumference, for rectangular tunnels with uniformly distributed around the circumference, for rectangular tunnels with uniformly distributed slots in the top and bottom walls, for rectangular tunnels with the slot distribution determined by a transformation from a uniformly slotted circular tunnel, and for a two-dimensional tunnel. The results of this paper are derived on the basis of an incompressible potential flow."

From Summary: "A limited investigation of a 1/24-scale dynamically similar model of the Navy Bureau of Aeronautics DR-77 design was conducted in Langley tank no. 2 to determine the calm-water take-off and the rough-water landing characteristics of the design with particular regard to the take-off resistance and the landing accelerations. During the take-off tests, resistance, trim, and rise were measured and photographs were taken to study spray. During the landing tests, motion-picture records and normal-acceleration records were obtained."

Report presenting a method for calculating the aerodynamic forces on the blades of a dual-rotating propeller with its thrust axis inclined to the air stream. Comparison of the fluctuating aerodynamic forces due to pitched or yawed operation of a dual-rotating propeller show that the fluctuation in forces on the front component tend to be greater than those on the rear component.

Report presenting specimens of five different root designs, proportioned in accordance with the design surveys, and specimens of a conventional fir-tree turbine root were fabricated from a titanium carbide cement bonded with nickel. Comparative strengths were determined by short-term tensile tests at 1200 degree Fahrenheit. Results regarding blade root evaluation and rotor-segment evaluation are provided.

Report presenting flight testing with two jet-propelled airplanes in rough air to investigate effects of sweep on gust loads and gust selectivity. Data was taken with an unswept-wing airplane and a 35 degree swept-wing airplane for incremental accelerations corresponding to airspeeds of 300 and 450 miles per hour. The results indicated that the swept-wing airplane experienced lower loads in turbulent air than the unswept-wing airplane.

From Summary: "Ignition delays of several propellant combinations obtained with a modified open-cup apparatus and with a small-scale rocket engine of approximately 50-pounds thrust were compared to study any correlations that might exist between the two methods of ignition-delay determination. The results were used in determining the relative utility of each apparatus."

"Several methods of cyclic de-icing of a gas-heated airfoil were investigated to determine ice-removal characteristics and heating requirements. The cyclic de-icing system with a spanwise ice-free parting strip in the stagnation region and a constant-temperature gas-supply duct gave the quickest and most reliable ice removal. Heating requirements for the several methods of cyclic de-icing are compared, and the savings over continuous ice prevention are shown. Data are presented to show the relation of surface temperature, rate of surface heating, and heating time to the removal of ice" (p. 1).

"The condensation pressure of air was determined over the range of temperature from 60 to 85 K. The experimental results were slightly higher than the calculated values based on the ideal solution law. Heat of vaporization of oxygen was determined at four temperatures ranging from about 68 to 91 K and of nitrogen similarly at four temperatures ranging from 62 to 78 K" (p. 1).

Report presents the correlation of extensive data obtained relating properties of wrought N-155 alloy under static, combined static and dynamic, and complete reversed dynamic stress conditions. Time period for fracture ranged from 50 to 500 hours at room temperature, 1,000 degrees, 1,200 degrees, and 1,500 degrees F.

Note presenting an extension of an analysis of the creep behavior of a slightly curved pin-ended H-section column under constant load to the slightly curved solid rectangular-section column. The analysis leads to a differential equation for the plastic strains at the midheight cross section.

Report presenting a study of the effects of high reactor and cycle temperatures and the effect of thickness of high-temperature fuel element materials on the feasibility of the nuclear-powered direct-air-cycle aircraft for flight at Mach number 1.5 and an altitude of 35,000 feet. Testing occurred over a range of reactor fuel temperatures, turbine-inlet temperatures, and reactor fuel plate thicknesses.

Report presenting a simplified limiting-blade-loading parameter for axial-flow-compressor blade elements derived from the application of a separation criterion used in two-dimensional boundary-layer theory to a typical suction-surface velocity distribution of a compressor blade element at design angle of attack. Results regarding two-dimensional cascade, compressor rotors, and compressor stators are provided.

Report presenting flight testing on models of the proposed Consolidated Vultee Aircraft Corporation MX-1626 airplane with nacelles and without nacelles. Results regarding drag level, design modifications, dampening, trimming, and the use of ventral boosters are provided.

From Summary: "Pressure distributions around circular cylinders placed perpendicular to the stream for subsonic and supersonic flow conditions have been obtained. Drag coefficients calculated from these wind-tunnel tests and from transonic free-flight tests are presented. Drag data are presented for the Mach number range of 0.3 to 2.9."

"Results of a free-flight investigation to determine the drag of circular, finite-length cylinders are presented for a Mach number range from about 0.5 to 1.3. Also included are drag results of previous experimental tests of infinite-length cylinders. Drag of circular cylinders at supersonic speeds is largely independent of fineness ratio and Reynolds number; whereas, at subsonic speeds, the drag of finite-length cylinders (fineness rations of about 60 and below) increases as their fineness ratios increase" (p. 1).

"The effects of primary and runback icing and frost formations on the drag of an 8-foot-chord NACA 651-212 airfoil section were investigated over a range of angles of attack from 20 to 80 and airspeeds up to 260 miles per hour for icing conditions with liquid-water contents ranging from 0.25 to 1.4 grams per cubic meter and datum air temperatures of -30 to 30 F. The results showed that glaze-ice formations, either primary or runback, on the upper surface near the leading edge of the airfoil caused large and rapid increases in drag, especially at datum air temperatures approaching 32 F and in the presence of high rates of water catch" (p. 1).

Investigation of the effect on zero-lift drag of varying the size and number of symmetrically mounted nacelles on a 45 degree sweptback wing and body combination as determined by free-flight tests of rocket-propelled models over a range of Mach and Reynolds numbers. The nacelle configuration consisted of a twin-engine nacelle near the fuselage, a combination of single-engine nacelles at the wing tip and fuselage, a large nacelle at the wing tip, and a large nacelle near the fuselage.