The following document describes data collected from a 14-month period of analyzing crustaceans containing radioactivity. Provided is information based on the change of radioactivity through seasonal changes.

From Introduction: "The airfoil sections tested, which differ only in thickness ratio, were the NACA 64-006, 64-008, 64-010, and 641-012. Lift, drag, and pitching-moment data were obtained for Mach numbers of 0.3 to that for tunnel choke at angles of attack of -2^o to 31^o. The results of this investigation are reported herein."

"During the flight investigation of the X-1 airplane the hinge moments of the elevator and aileron control surfaces have been measured over a Mach number range extending to above 1.0. The results of these measurements are presented in this paper" (p. 2).

Aerial image shows the result of an airborne radioactive survey over an area of 940 square miles in Apache County, Arizona with the approximate location of radioactivity anomalies found. Text describes methods used and discusses the anomalies.

Aerial image shows the result of an airborne radioactive survey over an area of 700 square miles in Sweetwater County, Wyoming with the approximate location of three radioactivity anomalies found. Text describes methods used and discusses the anomalies.

This document reports a preliminary airborne reconnaissance survey that was conducted in the mountain ranges of the northwest portion of Nevada.

"Altitude performance of a YJ71-A-7 turbojet engine, with afterburner inoperative, was determined in the NACA Lewis altitude wind tunnel over a wide range of flight conditions. Engine speed and exhaust-nozzle area were controlled independently during this investigation. The variation of corrected values of air flow, net thrust, and fuel flow with corrected engine speed was not defined by a single curve with changes in altitude at given flight Mach number" (p. 1).

From Introduction: "In response to the ever-increasing need for high thrust augmentation, an investigation was conducted that had as its primary objective the attainment of maximum exhaust-gas temperature and thrust (ref. 1). The investigation reported herein was therefore conducted to ascertain the operational limits of the most promising high-temperature afterburner design of reference 1 and to determine its performance over a wind range of flight conditions."

Report discussing the performance of a 20-inch-diameter ram-jet engine at Mach number 3.0 over a range of simulated altitudes from 60,500 to 66,500 feet. Information about the maximum combustor efficiency, range of exhaust-nozzle total pressures, lean blow-out, diffuser total-pressure recovery, and internal thrust coefficient is provided.

Report presenting an investigation of the performance of a 20-inch-diameter ram-jet engine at Mach number 3.0 in a free-jet facility over a range of simulated altitudes. Results regarding the diffuser characteristics, combustor performance, thrust output, and operational characteristics are provided.

During a compilation of ore reserves at Bull Canyon, it was apparent from the grade of submarginal mineralization that this material might be a low-grade reserve of importance. Mr. Lewis Hazen requested a memorandum of the results of the analysis; this memorandum is a response to that request.

From Introduction: "This report extends the short-bearing pressure-distribution function of Michell and Cardullo to give equations for the various bearing characteristics. This short-bearing approximation makes available formulas relating eccentricity ratio to applied load, attitude angle, angular position of peak film pressure to unit pressure on projected area."

From Introduction: "This paper will treat the problem in the suggested manner, beginning with the development of a suitable boundary condition to represent mathematically a homogeneous boundary which has the same flow characteristics, at a point in the flow sufficiently removed from the boundary as the actual physical boundary of alternate open and closed portions of the wall. Numerical results will be presented for circular tunnels with uniformly distributed around the circumference, for rectangular tunnels with uniformly distributed around the circumference, for rectangular tunnels with uniformly distributed slots in the top and bottom walls, for rectangular tunnels with the slot distribution determined by a transformation from a uniformly slotted circular tunnel, and for a two-dimensional tunnel. The results of this paper are derived on the basis of an incompressible potential flow."

Abstract: The results of both dry and wet attritioning of Temple Mountain ore are presented. In order to obtain effective attritioning on this ore, the amphaltite must be removed before attritioning. With the asphaltite present, dry attritioning causes a build-up of asphaltite on the surface of sand grains, with consequent loss of uranium values. In wet attritioning, the asphaltite is not broken down or attritioned, because of its low specific gravity and resilience.

From Summary: "A limited investigation of a 1/24-scale dynamically similar model of the Navy Bureau of Aeronautics DR-77 design was conducted in Langley tank no. 2 to determine the calm-water take-off and the rough-water landing characteristics of the design with particular regard to the take-off resistance and the landing accelerations. During the take-off tests, resistance, trim, and rise were measured and photographs were taken to study spray. During the landing tests, motion-picture records and normal-acceleration records were obtained."

Report presenting a method for calculating the aerodynamic forces on the blades of a dual-rotating propeller with its thrust axis inclined to the air stream. Comparison of the fluctuating aerodynamic forces due to pitched or yawed operation of a dual-rotating propeller show that the fluctuation in forces on the front component tend to be greater than those on the rear component.

From abstract: This investigation was conducted in order to develop a process whereby the most abundant zirconium ore, namely zircon, could economically be put into solution and purified adequately for use in hafnium separation processes employing liquid-liquid extraction. Secondary aims concerned the preparation of pure zirconyl chloride, zirconyl nitrate, zirconyl sulfate, and zirconium oxide from the zircon ore.

From introduction: This is the first in a series of reports describing an investigation of the chemistry of uranium(VI) orthophosphate solutions which is at present underway in this laboratory. Spectrophotometric, potentiometric and solubility studies have been carried out, and it is the first of these which is reported here.

This report is about The Chemistry of Uranium(VI) Orthophosphate Solutions. a series of reports describing an investigation of the Uranium(VI) Orthophosphate system.

Report presenting specimens of five different root designs, proportioned in accordance with the design surveys, and specimens of a conventional fir-tree turbine root were fabricated from a titanium carbide cement bonded with nickel. Comparative strengths were determined by short-term tensile tests at 1200 degree Fahrenheit. Results regarding blade root evaluation and rotor-segment evaluation are provided.

Report presenting flight testing with two jet-propelled airplanes in rough air to investigate effects of sweep on gust loads and gust selectivity. Data was taken with an unswept-wing airplane and a 35 degree swept-wing airplane for incremental accelerations corresponding to airspeeds of 300 and 450 miles per hour. The results indicated that the swept-wing airplane experienced lower loads in turbulent air than the unswept-wing airplane.

From Summary: "Ignition delays of several propellant combinations obtained with a modified open-cup apparatus and with a small-scale rocket engine of approximately 50-pounds thrust were compared to study any correlations that might exist between the two methods of ignition-delay determination. The results were used in determining the relative utility of each apparatus."

"Several methods of cyclic de-icing of a gas-heated airfoil were investigated to determine ice-removal characteristics and heating requirements. The cyclic de-icing system with a spanwise ice-free parting strip in the stagnation region and a constant-temperature gas-supply duct gave the quickest and most reliable ice removal. Heating requirements for the several methods of cyclic de-icing are compared, and the savings over continuous ice prevention are shown. Data are presented to show the relation of surface temperature, rate of surface heating, and heating time to the removal of ice" (p. 1).

None