The influence of dissolved oxygen and hydrogen and dilute sulfuric acid in 289/sup 0/C water on the stress-corrosion-cracking susceptibility of lightly and moderately sensitized Type 304 stainless steel was determined in constant-extension-rate tensile (CERT) tests. The CERT parameters and the fracture surface morphologies were correlated with the concentrations of dissolved oxygen and sulfate, and the electrochemical potentials of platinum and Type 304 stainless steel electrodes in simulated boiling-water reactor (BWR) environments. A particularly high susceptibility to intergranular cracking was found for the steel in the lightly sensitized condition at oxygen concentrations between approx. 0.05 and 0.2 ppM under slightly acidic conditions (pH approx. 6.0 at 25/sup 0/C), which may, in part, account for the pervasive nature of intergranular cracking in BWR piping systems. Scanning-transmission electron microscopy analyses revealed significant differences between samples in the lightly and the moderately sensitized condition with respect to the width, but not the depth, of the chromium-depleted region at the grain boundaries. The addition of 0.5 ppM hydrogen to the water had only a small mitigating effect on intergranular cracking in water containing oxygen and sulfuric acid at low concentrations; however, oxygen suppression to less than or equal to 0.05 ppM in the reactor-coolant water, …

The Direct Chlorination Process removes hydrogen sulfide from geothermal off-gases by reacting hydrogen sulfide with chlorine in the gas phase. Hydrogen chloride and elemental sulfur are formed by this reaction. The Direct Chlorination Process has been successfully demonstrated by an on-site operation of a pilot plant at the 3 M We HPG-A geothermal power plant in the Puna District on the island of Hawaii. Over 99.5 percent hydrogen sulfide removal was achieved in a single reaction stage. Chlorine gas did not escape the pilot plant, even when 90 percent excess chlorine gas was used. Because of the higher cost of chemicals and the restricted markets in Hawaii, the economic viability of this process in Hawaii is questionable.

This paper analyzes the geometrically nonlinear bending and collapse behavior of an elastic, simply supported cylindrical shell subjected to an inward-directed point load applied at midlength. The large displacement analysis results for this thin (R/t = 638) poked cylinder were obtained from the STAGSC-1 finite element computer program. STAGSC-1 results are also presented for two other point-loaded shell problems: a pinched cylinder (R/t = 100), and a venetian blind (R/t = 250).

We report on the use of a 5.8 GHz microwave applicator to treat choroidal melanoma (Greene) in rabbits. The physical requirements needed to treat these intraocular tumors are quite different from those encountered elsewhere in the body. From a trans-scleral approach the penetration needed is minimal (5 to 10 mm.). The fibrous sclera is the only structure between the heat source and the tumor. The sclera has a relatively low water content when compared to tumor. This fact in addition to the frequency dependent interactions of tissue and electromagnetic radiation, results in an advantage to the use of the 5.8 GHz microwave device in treating intraocular malignancies.

The W-2 SLSF (Sodium Loop Safety Facility) experiment was an instrumented in-reactor test performed to characterize the failure response of full-length, preconditioned LMFBR prototypic fuel pins to slow transient overpower (TOP) conditions. Although the test results were expected to confirm analytical predictions of upper level failure and fuel expulsion, an axial midplane failure was experienced. Extensive post-test analyses were conducted to understand all of the unexpected behavior in the experiment. (1) The initial post-test effort focused on the temperature oscillations recorded by the 54 thermocouples used in the experiment. In order to synthesize the extensive data records and identify patterns of behavior in the data records, a computer-generated film was used to present the temperature data recorded during the experiment.

The research program in nuclear physics in the Physics Division spans a broad range of activities and contributes to many of the major questions in the discipline. Activities may be roughly divided into three broad categories. Research with the tandem-linac in heavy-ion physics is doing well, though laboring under severe budgetary constraints, and outside use of the facility has increased substantially. Progress on the construction of the full ATLAS facility is coming along expeditiously and it is expected to be completed on schedule in 1985. In medium-energy physics, activities are continuing at LAMPF, as well as other accelerators, though considerable effort was devoted this year to the preparation of a proposal for a national electron accelerator facility.

Report discussing a project to design, build, and test a latent heat storage device using cross-linked, high-density polyethylene (HDPE). This report provides an update on progress up to the point that the device is ready to test.

Fluid damping plays an important role for structures submerged in fluid, subjected to flow, or conveying fluid. This design guide presents a summary of calculational procedures and design data for fluid damping for circular cylinders vibrating in quiescent fluid, crossflow, and parallel flow.

The susceptibility of a cantilevered tube conveying water to self-excitation by leakage flow through a slip joint is assessed experimentally. The slip joint is formed by inserting a smaller, rigid tube into the free end of the cantilevered tube. Variations of the slip joint annular gaps and engagement lengths are tested, and several mechanisms for self-excitation are described.

This Phase II study provides further analysis for a seasonal-storage solar-heating system utilizing two existing underground, concrete tanks in the National Historic Park of the Charlestown Navy Yard in Boston. The initial Phase I study was reported in ANL-82-90. The new results focus on the effect of including a heat pump in the system to extend the useful heat-storage capacity of the tanks. The analysis was performed with MINSUN Version III, a computer simulation model written particularly for seasonal storage systems. Input parameters were derived in Phase I and reviewed and updated for this study. Three collector types were studied with and without a heat pump. Results indicate a definite performance and economic improvement for all collector types by including the heat pump. Flat plate collectors showed substantially greater improvement due to their more pronounced increase in efficiency at the lower inlet temperatures. With the heat pump, all three collectors provide comparable performance, and the flat plates were chosen as the design system due to their lower cost. A design system of 2300 meters sq. flat plate collectors with heat pump was selected. The system provides a solar fraction of 50% for the 2167 MWH annual heat load. The annualized …

This report summarizes the work completed on a project concerned with engineering models in dynamic plasticity. The concept of the endochronic theory of viscoplasticity and its subsequent improvement are discussed briefly. Applications and extensions of the theory to various dynamic problems are presented. In particular, the strain-rate effect in the improved endochronic theory and its application to wave propagation problems are discussed. Comparing the numerical results with other calculations and experimental data, it appears that endochronic theory provides a promising representation of realistic material behavior. At the same time endochronic theory is often numerically more efficient than other formulations.

The results of a program to provide an experimental data base for estimating the radiological consequences from a hypothetical sabotage attack on a light-water-reactor spent fuel shipping cask in a densely populated area are presented. The results of subscale and full-scale experiments in conjunction with an analytical modeling study are described. The experimental data were used as input to a reactor-safety consequence model to predict radiological health consequences resulting from a hypothetical sabotage attack on a spent-fuel shipping cask in the Manhattan borough of New York City. The results of these calculations are presented.

Optical second-harmonic generation (SHG) is sensitive enough to respond to a submonolayer of surface atoms or molecules. It can therefore be used to probe surfaces or interfaces between two centrosymmetric media. The surface-specific nature of this optical method offers some advantages. We have demonstrated in recent experiments that resonant SHG can allow us to obtain spectroscopic data of submonolayers of adsorbed molecules on a surface. The signal was so strong that less than one tenth of a monolayer of dye molecules could be easily detected. The method can be applied to molecules adsorbed at an interface between two dense media such as a liquid/solid interface. Then, using SHG, adsorption isotherms of adsorbates on substrates can be measured. One is often interested in how large the bulk contribution to SHG is in comparison with the surface contribution. Second-order nonlinear optical processes are forbidden in a medium with inversion symmetry only in the electric-dipole approximation. Could SGH from electric-quadrupole and magnetic-dipole contributions in the bulk be so strong as to mask out the electric-dipole contribution from the surface. We have found that the SH signal from a centrosymmetric substrate can be changed appreciably by the adsorption of a monolayer. This clearly indicates …

Lower hybrid current-drive experiments have been carried out on the PLT Tokamak. Steady currents up to 175 kA have been maintained for three seconds and 400 kA for 0.3 sec by the rf power alone. The principal current carrier appears to be a high energy (approx. 100 keV) electron tail, concentrated in the central 20 to 40 cm diameter core of the 80-cm PLT discharge. Effective current drive is observed only for anti n/sub e/ less than or equal to 8 x 10/sup 12/ cm/sup -3/. This limitation may be a wave propagation phenomenon and not a fundamental plasma physics effects.

The requirements to be met by Pockels cell drivers for incorporation into the Novette and Nova Laser systems are presented, and critical aspects of the specification examined. A high-performance pulse generator has been developed to meet these requirements using new thyratron technology from the English Electric Valve Co. Ltd. Two closely related versions have been built; a 10KV output unit with 9 nsec risetime into five parallel 50-ohm loads and a faster 5KV output driver with 3.5 nsec risetime into a single 50-ohm load. The design approach for optimizing performance, using the new tubes in relation to the LLNL specification is described, including the techniques used for control of electromagnetic interference.

A breeding ratio of at least 1.2 was a design goal for CRBRP. The value for the initial core (using plutonium with 11% /sup 240/Pu) calculated with ENDF/B-IV data is 1.27. Engineering mock-up studies for CRBRP were made in ZPPR-11. Analysis of ZPPR-11 using ENDF/B-IV data showed consistent underprediction of K/sub eff/ by about 1.5% and overpredictions of the /sup 238/U capture to /sup 239/Pu fission ratio (C8/F9) between 5% and 8%. These results are typical for all LMFBR critical assemblies at ANL. The following approach was used to determine the breeding ratio: sensitivity analysis of a range of fast reactor benchmarks and a fit to the experimental data by data adjustment; tests of the adjusted data against experiments in ZPPR-11; calculations for CRBRP with ENDF/B-IV data and the adjusted data to predict the breeding ratio bias; and estimates of k/sub eff/ and breeding ratio uncertainties using data sensitivities for CRBRP.

New switching power supplies were designed for the 10 mm laser amplifiers in the Nova Master Oscillator Room. The flashlamp supply must be repratable. Therefore, we designed a constant current, linearly charging power supply. Since it is a capacitor, the load varies throughout the charge cycle. At first the load is great, and di/dt of load current is at a maximum. As the capacitor charges the initial conditions for each cycle change, the power supply in effect sees a smaller capacitance, and di/dt decreases. We need a way of gradually increasing the on-time of the current pulses so that the transistors in the power bridge are turned off when they reach their maximum peak current. The normal current sense response of the control chip is not fast enough to be useful for our application. The deadtime, or the time that all the bridge transistors are turned off, is fixed so that as the pulse width varies so does the period. We end up with a constant peak current, switching power supply whose frequency varies from 50 khz to 20 khz. Finally, an overcurrent latch protects the transistors from bridge or transformer faults. The circuit is described and results are shown.

Increasing effort is being put into engineering designs of reactors and reactor-like magnetic confinement experiments. A central question concerns the methods of heating, fueling, and maintaining the plasmas, functions that primarily are now performed by neutral beams. Planning in the USA does not include the use of neutral beams on tokamaks in the 1990's and beyond. Tandem mirrors, however, will use energetic beams (sloshing ion beams) in the end plugs to produce electrostatic potentials that will confine plasma ions. These systems will be based on the production, acceleration, transport, and neutralization of negative hydrogen-ion (D/sup -/), multiampere beams with energies of 200-to 500-keV. In addition, lower-energy D and T beams may be used. These systems must operate steady state, with high reliability, and be compatible with radiation from a D-T burning plasma.

A regional model that can predict groundwater movement through the reference repository location and surrounding area is essential to assessing the site suitability for a nuclear waste repository. During the last two decades, several models have been developed to handle complicated flow patterns through complex geologic materials. The basic problem, however, is obtaining the data base needed to apply these models. The hydrological data needed include the spatial distribution of effective porosity, the hydraulic conductivity tensor and its variation in space, values of specific storage, the hydraulic head distribution, and the fluid properties. In this report, we discuss conventional methods of obtaining vertical hydraulic conductivity and examine their applicability to the BWIP site. 39 references, 12 figures, 4 tables.

Progress is reported in research on: the baseline ecology of the Idaho National Engineering Laboratory (INEL), the effects of disturbance on animal and plant communities, and the behavior of radionuclides in the environment surrounding radioactive waste sites. Separate abstracts have been prepared for individual reports. (ACR)

This report presents a method for evaluating relative environmental impacts of coal transportation modes (e.g., unit trains, trucks). Impacts of each mode are evaluated (rated) for a number of categories of environmental effects (e.g., air pollution, water pollution). The overall environmental impact of each mode is determined for the coal origin (mine-mouth area), the coal or coal-energy product destination (demand point), and the line-haul route. These origin, destination, and en route impact rankings are then combined into a systemwide ranking. Thus the method accounts for the many combinations of transport modes, routes, and energy products that can satisfy a user's energy demand from a particular coal source. Impact ratings and system rankings are not highly detailed (narrowly defined). Instead, environmental impacts are given low, medium, and high ratings that are developed using environmental effects data compiled in a recent Argonne National Laboratory report entitled Data for Intermodal Comparison of Environmental Impacts of Inland Transportation Alternatives for Coal Energy (ANL/EES-TM-206). The ratings and rankings developed for this report are generic. Using the method presented, policy makers can apply these generic data and the analytical framework given to particular cases by adding their own site specific data and making some informed judgements. …

Progress is reported in the following research areas: (1) high resolution, high sensitivity luminescence and other spectroscopic techniques, and (2) advanced methodologies for measurement of toxic effluents from energy processes. (ACR)

We have measured the production cross section and momentum distribution of K/sup -/ produced at 0/sup 0/ in /sup 28/Si + /sup 28/Si collisions at an energy of 2.1 GeV/nucleon. The K/sup -/ spectrum is approximately exponential. The large yield in the subthreshold production of K/sup -/ that we observe corresponds to a production rate of 1K/sup -/ per 50 collisions at impact parameters less than 1f. Productions mechanisms involving collective effects and thermal equilibration are discussed.

The economic future of methanol is reviewed in light of its potential uses as a substitute for traditional hydrocarbon fuels and feedstocks as well as some evolving new uses. Methanol's future market position will depend strongly on its production cost in comparison with competitive products. One promising way to reduce the production cost is by use of an improved catalyst in the process by which methanol is obtained from the feedstock - which can be either natural gas or a similar product such as synthesis gas from coal gasification. To estimate the potential cost savings with an improved catalyst, we have based our analysis on a recent study which assumed use of synthesis gas from underground coal gasification as a feedstock for making methanol. The improved catalyst we studied was an actinide oxide whose features include high tolerance to sulfur and heat, and a yield of about 4 mol% methanol per pass with a 2/1 mixture of H/sub 2//CO. We calculated the effect of this catalyst on methanol production costs in a 12,000-bbl/day plant. The result was a saving of from 1 cent to 2.5 cent per gallon on the total methanol synthesis cost of 23 cents per gallon (i.e., …