This report presents the results of a series of negative thrust and torque measurements made with a 4 foot diameter model of a conventional aluminum-alloy propeller. The tests were made in the 20-foot propeller-research tunnel of the National Advisory Committee for Aeronautics. The results show that the negative thrust is considerably affected by the shape and size of the body behind the propeller, that the maximum negative thrust increases with decrease in blade-angle setting, and that the drag of a locked propeller may be greatly reduced by feathering it into the wind.

The present paper presents an attempt to coordinate the available theoretical and experimental data on planing surfaces so as to develop an approximate analytical method for the determination of the water resistance of a seaplane without any preliminary towing tests in the tank.

"This paper presents a mathematical discussion of the laminar boundary layer, which was developed with a view of facilitating the investigation of those boundary layers in particular for which the phenomenon of separation occurs. The treatment starts with a slight modification of the form of the boundary layer equation first published by Von Mises. Two approximate solutions of this equation are found, one of which is exact at the outer edge of the boundary layer while the other is exact at the wall" (p. 541).

The subject of the present paper is confined to the investigations and methods employed by the Fiat company in their studies on the altitude performance of an air-cooled engine of the production type. The experimental set-up as well as test engine data are provided.

This note presents the results of flight pressure distribution tests on the right upper wing panel of a Douglas M-3 airplane equipped with a semicircular wing tip. The results are given in tables and curves in such form that the load distribution for any force coefficient within the usual range encountered in flight may easily be determined.

"This reports presents the results of pressure distribution tests on a thick, tapered and twisted monoplane wing model. The investigation was conducted for the purpose of obtaining data on the aerodynamic characteristics of the new wing and to provide additional information suitable for use in the design of tapered cantilever wings. The tests included angles of attack up to 90 degrees. The span loading over the wing was approximately of elliptical shape, which gave rise to relatively small bending moments about the root" (p. 97).

This report presents the results of an investigation to determine experimentally the instantaneous pressures at the discharge orifice of a common-rail fuel injection system in which the timing valve and cut-off valve were at some distance from the automatic fuel injection valve, and also to determine the methods by which the pressure fluctuations could be controlled. The results show that pressure wave phenomena occur between the high-pressure reservoir and the discharge orifice, but that these pressure waves can be controlled so as to be advantageous to the injection of the fuel. The results also give data applicable to the design of such an injection system for a high-speed compression-ignition engine.

Report issued by the U.S. Bureau of Mines discussing the purchasing procedures documented by the Miami Copper Company in Arizona. Supplies, invoices, discounts, and accounting procedures are described in detail. This report includes tables, and illustrations.

Report issued by the U.S. Bureau of Mines on two samples of crude oil collected from the Greasewood Flat area of northwestern Colorado. These samples were analyzed for many characteristics, and an approximate summary of those characteristics are presented. The report contains two tables of data.

Formulas are given for the propelling or drag force experience in a uniform air stream by an airfoil or an airfoil-aileron combination, oscillating in any of three degrees of freedom; vertical flapping, torsional oscillations about a fixed axis parallel to the span, and angular oscillations of the aileron about a hinge.

Provides information about growing quince, including soil requirements, propagation, varieties, planting and care of trees, and insect and disease control.

"The fundamental principles of fluid flow, pressure losses, and heat transfer have been presented and analyzed for the case of a smooth tube with fully developed turbulent flow. These equations apply to tubes with large length-diameter ratios where the flow is at a high Reynolds Number. The error introduced by using these equations increases as the magnitude of the tube length and the air-flow Reynolds Number approaches the values encountered in modern radiator designs" (p. 1).

Describes how to construct a building that uses rammed earth for walls.

Using the method of weighing fuel collected in a receiver during a definite interval of the injection period, rates of discharge were determined, and the effects noted, when various changes were made in a fuel-injection system. The injection system consisted primarily of a by-pass controlled fuel pump and an automatic injection valve. The variables of the system studied were the pump speed, pump-throttle setting, discharge-orifice diameter, injection-valve opening and closing pressures, and injection-tube length and diameter.

This report details the advantages and construction of tailless airplanes. Both a glider and a powered model were built and the specifications of both airplanes are listed.

"This investigation was conducted to determine the effectiveness of various surface coatings as a means for preventing ice formations on aircraft in flight. The substances used as coatings for these tests are divided into two groups: compounds soluble in water, and those which are insoluble in water. It was found that certain soluble compounds were apparently effective in preventing the formation of ice on an airfoil model, while all insoluble compounds which were tested were found to be ineffective" (p. 1).

It is shown that the lift distribution for a biplane with unequal chords may be calculated by the method developed in NACA Technical report no. 458 if corrections are made for the inequality in chord lengths. The method is applied to four cases in which the upper chord was greater than the lower and good agreement is obtained between observed and calculated lift coefficients.

"The present report includes a description of the making of three-component measurements on a full-size float mounted on an actual airplane and the comparison of the results with those from two models of the same form but of different size which had been tested in the towing tank. The purpose of the comparison is to determine the effect of the Reynolds Number on the results of model tank tests. Following a brief discussion of previous tests intended to elucidate the problem of scale effect on float systems and a description of the testing equipment, the choice of the reference quantities to be used in the comparison is discussed" (p. 1).

A guide to evaluating the health and maturity of a hen for the purpose of egg production.

Report presenting a method for analyzing strains measured on three or four gage lines intersecting at 45 degrees, which helps determine the state of stress at a point on a plane. An equation for adjustment factor and a master curve is provided, which can be memorized and easily used in the future.

Circular presenting a description of the Short Scylla, which is a 39-passenger landplane with four Bristol Jupiter XF BM engines. A description of the characteristics, blueprints, and photographs of the aircraft are provided.

The problems of using models in planing tests are addressed. If one passes from the model to a hull of linear dimensions n times greater, the speeds are connected by the law of mechanical similitude. The normal forces given by the hydrodynamic equations (perfect fluid) also follow the law of dynamic similitude (Reech's method) and are multiplied by n(exp 3). A series of tests were performed and the actual results were compared to theoretical results.

From Summary: "A method is presented for the rapid calculation of the pressure distribution over an airfoil section when the normal-force distribution and the pressure distribution over the "base profile" (i.e., the profile of the same airfoil were the camber line straight and the resulting airfoil at zero angle of attack) are known. This note is intended as a supplement to N.A.C.A. Report Nos. 631 and 634 wherein methods are presented for the calculation of the normal-force distribution over plain and flapped airfoils, respectively, but not of the pressures on the individual surfaces. Base-profile pressure-coefficient distributions for the usual N.A.C.A. family of airfoils, which are also suitable for several other commonly employed airfoils, are included in tabular form. With these tabulated base-profile pressures and the computed normal-force distributions, pressure distributions adequate for most engineering purposes can be obtained."

Presented here are experimental results obtained from a brief investigation of the appearance, penetration, and dispersion of oil sprays injected into a chamber of highly heated air at atmospheric pressure. The development of single sprays injected into a chamber containing air at room temperature and at high temperature was recorded by spray photography equipment. A comparison of spray records showed that with the air at the higher temperature, the spray assumed the appearance of thin, transparent cloud, the greatest part of which rapidly disappeared from view. With the chamber air at room temperature, a compact spray with an opaque core was obtained. Measurements of the records showed a decrease in penetration and an increase in the dispersion of the spray injected into the heated air. No ignition of the fuel injected was observed or recorded until the spray particles came in contact with the much hotter walls of the chamber about 0.3 second after the start of injection.