Describes methods and considerations for shipping farm produce by parcel post.

Describes the damage caused by cattle grubs and provides methods for their control.

Provides steps for planting, cultivating, and marketing Christmas trees.

Provides information about growing quince, including soil requirements, propagation, varieties, planting and care of trees, and insect and disease control.

Describes how to construct a building that uses rammed earth for walls.

A guide to velvet-bean culture, including a discussion of its uses as food for livestock and humans.

Describes the benefits of growing tomatoes in greenhouses for improved quality and marketability. Discusses requirements and methods for successfully growing greenhouse tomatoes.

Describes the damage that the chalcid can cause to an alfalfa seed crop, and various measures that a farmer can take to control it.

A guide to evaluating the health and maturity of a hen for the purpose of egg production.

"The aerodynamic forces on an oscillating airfoil or airfoil-aileron combination of three independent degrees of freedom were determined. The problem resolves itself into the solution of certain definite integrals, which were identified as Bessel functions of the first and second kind, and of zero and first order. The theory, based on potential flow and the Kutta condition, is fundamentally equivalent to the conventional wing section theory relating to the steady case" (p. 291).

"A 1/7.06 full-size model of the NC-type hull was tested in the N.A.C.A. tank by both the general method and the specific or free-to-trim method. The results of the tests are given in curves plotted as non dimensional coefficients and are compared with the test results of N.A.C.A. model 11-A. The NC model (N.A.C.A. model 44) shows higher resistance than model 11-A at hump speed but lower resistance at high speeds. Model 44 has a higher best trim angle at the jump and a lower maximum positive trimming moment than model 11-A. At high speeds the best trim angle and the trimming moments of the two models are approximately the same" (p. 1).

The results of tests of six airfoils having the N.A.C.A. 230 mean line and varying in thickness from 0.06c to 0.21c are presented. These results agree with previous findings in showing that aerodynamically the best section is one of moderate thickness. The data are of value mainly in connection with the design of tapered wings having sections based on the N.A.C.A. 230 mean line.

"The tests reported in this paper were made to devise simple engine tests which would rate fuels as to their comparative value and their suitability for the operating conditions of the individual engine on which the tests are made. Three commercial fuels were used in two test engines having combustion chambers with and without effective air flow. Strictly comparative performance tests gave almost identical results for the three fuels. Analysis of indicator cards allowed a differentiation between fuels on a basis of rates of combustion" (p. 1).

The lift, drag, and center of pressure characteristics of a model of the Fowler variable-area wing were measured in the NACA 7 by 10 foot wind tunnel. The Fowler wing consists of a combination of a main wing and an extension surface, also of airfoil section. The extension surface can be entirely retracted within the lower rear portion of the main wing or it can be moved to the rear and downward. The tests were made with the nose of the extension airfoil in various positions near the trailing edge of the main wing and with the surface at various angular deflections. The highest lift coefficient obtained was C(sub L) = 3.17 as compared with 1.27 for the main wing alone.

"This paper reports wind-tunnel tests giving the lift coefficients of large-scale wing-nacelle combinations both with and without the propeller. The tests were made to show the effect of nacelles, and idling and stopped propellers on the landing speeds of tractor monoplanes. Four types of nacelles with various cowlings were used in numerous positions with respect to both a Clark Y and a thick airfoil. The effect of both the idling and stopped propeller on lift, and consequently on landing speed, was negligible" (p. 1).

"Air flow about the fuselage and empennage during a high-angle-of-attack spin was made visible in flight by means of titanium-tetrachloride smoke and was photographed with a motion-picture camera. The angular relation of the direction of the smoke streamer to the airplane axes was computed and compared with the angular direction of the motion in space derived from instrument measurement of the spin of the airplane for a nearly identical mass distribution. The results showed that the fin and upper part of the rudder were almost completely surrounded by dead air, which would render them inoperative; that the flow around the lower portion of the rudder and the fuselage was nonturbulent; and that air flowing past the cockpit in a high-angle-of-attack spin could not subsequently flow around control surfaces" (p. 1).

"Tests were made on a model wing with three different sized split trailing-edged flaps, in the NACA 7 by 10 foot wind tunnel. The flaps were formed of the lower rear portion of the wing and were rotated downward about axes at their front edges. The lift, drag, and center of pressure were measured with the axis in its original position and also with it moved back in even steps to the trailing edge of the main wing, giving in effect an increase in area. The split flaps when deflected about their original axis locations gave slightly higher maximum lift coefficients than conventional trailing-edge flaps, and the lift coefficients were increased still further by moving the axes toward the rear" (p. 1).

"In order to determine whether or not flaps could be expected to have any beneficial effect on take-off performance, the distances required to take off and climb to an altitude of 50 feet were calculated for hypothetical airplanes, corresponding to relatively high-speed types and equipped with several types of flap. The types considered are the Fowler wing, the Hall wing, the split flap, the balanced split flap, the plain flap, and the external-airfoil flap. The results indicate that substantial reductions in take-off distance are possible through the use of flaps, provided that the proper flap angle corresponding to a given set of conditions is used" (p. 1).

From Summary: "Performance tests were made using a rectangular displacer arranged so that the combustion air was forced through equal passages at either end of the displacer into the vertical-disk combustion chamber of a single-cylinder, four-stroke-cycle compression-ignition test engine. After making tests to determine optimum displacer height, shape, and fuel-spray arrangement, engine-performance tests were made at 1,500 and 2,000 r.p.m. for a range of boost pressures from 0 to 20 inches of mercury and for maximum cylinder pressures up to 1,150 pounds per square inch. The engine operation for boosted conditions was very smooth, there being no combustion shock even at the highest maximum cylinder pressures. Indicated mean effective pressures of 240 pounds per square inch for fuel consumptions of 0.39 pound per horsepower-hour have been readily reproduced during routine testing at 2,000 r.p.m. at a boost pressure of 20 inches of mercury."

Discussed here are a series of systematic tests being conducted to compare different lateral control devices with particular reference to their effectiveness at high angles of attack. The present tests were made with six different forms of floating tip ailerons of symmetrical section. The tests showed the effect of the various ailerons on the general performance characteristics of the wing, and on the lateral controllability and stability characteristics. In addition, the hinge moments were measured for the most interesting cases.

Some preliminary results of full scale wind tunnel testing to determine the best means of reducing the tail buffeting and wing-fuselage interference of a low-wing monoplane are given. Data indicating the effects of an engine cowling, fillets, auxiliary airfoils of short span, reflexes trailing edge, propeller slipstream, and various combinations of these features are included. The best all-round results were obtained by the use of fillets together with the National Advisory Committee for Aeronautics (NACA) cowling.

"An investigation was conducted in the N.A.C.A. full-scale wind tunnel to determine the effects of exposed rivet heads on the aerodynamic characteristics of a metal-covered 6 by 36 foot Clark Y airfoil. Lead punching simulating 1/8 inch rivet heads were attached in full-span rows at a pitch of 1 inch at various chord positions. Tests were made at velocities varying from 40 to 120 miles per hour to investigate the scale effect" (p. 1).

This report is the fifth of a series presenting the results of strength tests of thin-walled cylinders and truncated cones of circular and elliptic section; it includes the results obtained from torsion tests on 30 cylinders, pure bending tests on 30 cylinders, and combined transverse shear and bending tests on 60 cylinders. All the cylinders tested were elliptic section with the ends clamped to rigid bulkheads. In the pure bending and combined transverse shear and bending tests the loads were applied in the plane of the major axis. The results of the tests on elliptic cylinders are correlated with the results of corresponding tests on circular cylinders and are presented in charts suitable for use in design.

During an extensive study of all types of rotating wings, the NACA examined the cyclogiro rotor and made an aerodynamic analysis of that system (reference 1). The examination disclosed that such a machine had sufficient promise to justify an experimental investigation; a model with a diameter and span of 8 feet was therefore constructed and tested in the 20-foot wind tunnel during 1934. The experimental work included tests of the effect of the motion upon the rotor forces during the static-lift and forward-flight conditions at several rotor speeds and the determination of the relations between the forces generated by the rotor and the power required by it.