The effect of corrosion on the tensile properties of duralumin while stressed is shown in graphical form. According to the test results, duralumin sheet, coated with aluminum, maintains its initial properties unimpaired for corrosion periods as long as 60 days with an applied tensile stress as high as 20,000 lb/sq.in., which is approximately one-half the stress corresponding to the yield point as defined here. In these tests, that material which had been heat-treated by being quenched in cold water, though far inferior to similar material having the aluminum coating, was superior to the sheet material which was heat treated by being quenched in hot water.

Given here are a set of column strength curves that are intended to simplify the method of determining the size of struts in an airplane structure when the load in the member is known. The curves will also simplify the checking of the strength of a strut if the size and length are known. With these curves, no computations are necessary, as in the case of the old-fashioned method of strut design. The process is so simple that draftsmen or others who are not entirely familiar with mechanics can check the strength of a strut without much danger of error.

"A peculiar phenomena in seaplane landing is observed and reported. The seaplane having executed a normal fast landing at low incidence, a forward movement of the control stick effected an unusual condition in that the seaplane left the water suddenly in an abnormal attitude. The observations describing this phenomena are offered as a warning against possible accident and as a conjectural cause of seaplane landing accidents of a certain kind" (p. 1).

The tests described in this report constitute a preliminary investigation of airfoil boundary layer control, as carried out in the atmospheric wind tunnel of the Langley Memorial Aeronautical Laboratory, from February to August, 1927. Tests were made on a U.S.A. 27 airfoil section with various slot shapes and combinations, and at various amounts of pressure or suction on the slots. The lift of airfoils can be increased by removing or by accelerating the boundary layer. Removing the boundary layer by suction is more economical than to accelerate it by jet action. Gauze-covered suction slots apparently give the best results. When not in operation, all suction slots tested had a detrimental effect upon the aerodynamic characteristics of the airfoil which was not apparent with the backward-opening pressure slots. Thick, blunt-nose airfoils would seem to give best results with boundary layer control.

Tests were conducted to investigate the possibility of a serious accident arising from unintentional contact with the water in substantially horizontal flight at high speed. Referring to vector diagrams on Figure 2, it will be seen that a very dangerous condition may arise if the float be allowed to come in contact with the water at high speeds as, for example, when flying at high speed just above the water. The initial diving moment due to suction and drag combined may be great enough to cause the seaplane to nose under before the pilot is able to control the motion.

"This report, the third of a series of four, describes a simple system for designing propellers of a standard form. In this report, the system is based on tests of a family of model propellers of standard Navy form, the data from which have been extended by means of calculations to cover the complete range likely to be found in practice. However, it can be worked out for any family having propellers of one general form" (p. 1).

This report is the second of a series of four on propeller design, and describes the method used to extend the data obtained from tests on a family of thirteen model propellers to include all propellers of the same form likely to be met in practice. This necessitates the development of a method of propeller analysis which when used to calculate the powers and efficiencies gives results which check the tests throughout their range.

"This report is the first of a series of four on propeller design and contains a description of the blade elements or modified Drzewiecke theory as used in the Bureau of Aeronautics, U.S. Navy Department. Blade interference corrections are used which were taken from R.& M. NO. 639 of the British Advisory Committee for Aeronautics. The airfoil characteristics used were obtained from tests of model propellers, not from tests of model wings" (p. 1).

Three groups of airfoils have been tested in the variable density wind tunnel. The first group contains three airfoils. The second group is a systematic series of twenty-seven airfoils. The third group consists of several frequently used wing sections.

Calculations of the magnitude of the correction factors and the range of their variations for wind tunnel models used in making aircraft performance predictions were made for 23 wind tunnel models. Calculated performances were compared with those actually determined for such airplanes as have been built and put through flight test. Except as otherwise noted, all the models have interplane struts and diagonal struts formed to streamwise shape. Wires were omitted in all cases. All the models were about 18 inches in span and were tested in a 4-foot wind tunnel. Results are given in tabular form.

These tests were undertaken to find the effect of turbulence in the air stream upon the lift and drag forces measured on models in the four-foot wind tunnel at the Massachusetts Institute of Technology. Maximum lifts and minimum drags were measured on Gottingen-387 and R.A.F.-15 airfoils, minimum drag on a streamlined strut, and the static pressure gradients for different conditions of turbulence were investigated. The results show that the scale of the turbulence (as defined in this report) has a marked effect upon the measured forces on models tested in the tunnel as well as on the pressure gradient, and it is recommended that further investigation of the phenomena be made with the aid of smoke and small wind vanes.

This note investigates the effect of high altitude or low atmospheric pressure upon the operation of an engine and the effect of the low pressure and lack of oxygen and of the very low temperatures upon the pilot and upon the performance of the airplane itself.

A simple and easily applied method of calculating the dimensions and horsepower necessary for an airship to have any given performance is described and illustrated by examples. The method includes means for estimating the changes in performance or in size when modifications or new features are introduced into a design, involving increase or saving in weights, or changes in resistance or propulsive efficiency.

"This note, prepared for the National Advisory Committee for Aeronautics, contains the demonstration that the pressure around the circular cross section of an elongated airship, plotted against the diameter of symmetry, can be expected to be represented by a straight line" (p. 1).

Report discussing Issues and techniques relative to the adaptation of aircraft engines to high altitude flight. Covered here are the limits of engine output, modifications and characteristics of high altitude engines, the influence of air density on the proportions of fuel mixtures, methods of varying the proportions of fuel mixtures, the automatic prevention of fuel waste, and the design and application of air pressure regulators to high altitude flying. Summary: 1. Limits of engine output. 2. High altitude engines. 3. Influence of air density on proportions of mixture. 4. Methods of varying proportions of mixture. 5. Automatic prevention of fuel waste. 6. Design and application of air pressure regulators to high altitude flying.

"The experiments discussed here were performed to determine whether radiators having similar cooling properties offer less resistance when incorporated into the fuselage, than when the hitherto customary arrangement is employed, with the radiator in the free air current more or less independent of the fuselage. The experiments indicated that the quantity of air flowing through the radiator is greatest when the fuselage and the radiator are separate. However, separate radiators cause more air resistance" (p. 1).

Note presenting an investigation to determine what effect joints connected with brackets, nails, and glue has on the strength of aircraft wing spars. Equations used to determine the results of loading tests are provided.

Report discussing a new instrument is described which is capable of simultaneously recording the position of the three controls of an airplane. The records are taken photographically on a standard N.A.C.A. film drum and the instrument can be quickly installed in any airplane.

The choice of the numbers of revolutions and of the diameter, the distribution of thrust, and the values of the constants in the aerodynamical equations of the propeller are discussed.

The air flow and the air force created by all elements of the propeller blades lying in a ring located between two concentric circles around the propeller axis are independent of what happens in other rings.

"No rational column formula has yet been developed which gives results which are sufficiently precise for the design of airplane members, and consequently it is necessary to fall back upon experimental testing. In order to derive the maximum benefit from experiments, however, it is necessary that the experiments be guided by theory. It is the object here to modify existing formulae that may be obtained with a minimum number of tests" (p. 1).

Here, the purpose is to show that the characteristic performance of a syphon diaphragm can be predicted from a knowledge of its stiffness and of its dimensions. The proof is based on a mathematical analysis of this type of diaphragm, together with enough experimental data to prove the validity of the assumptions and the sufficiency of the analysis. Equations are developed for the performance of syphons under various conditions of loading, both for concentrated loads and for hydrostatic pressure.

Discussed here are the principles and operation of aircraft engine superchargers used to maintain and increase engine power as aircraft encounter decreases in the density of air as altitude rises. Details are given on the design and operation of the centrifugal compressors. A method is given for calculating the amount of power needed to drive a compressor. The effects of the use of a compressor on fuel system operation and design are discussed. Several specific superchargers that were in operation are described.

Discussed here is a new type of wind tunnel, its advantages, the difficulties attendant upon its use, and the special methods required for its operation. The main difference between the new type of wind tunnel and the ones now in operation is the use of a different fluid. The idea is to diminish the effect of viscosity.