Methods of conversion of UF4 to U3O8 by fusion with ammonium oxalate dihydrate and other salts are described.

Abstract: The procedures recommended for analysis in Department 190 Laboratories, in the Limits Control Laboratory, and in the Analytical Development Laboratories, of all process materials from the HCP cycle are presented in a stepwise manner. A description of the characteristics of each sample type along with a brief description of factors involved in the Analytical Quality Control program is included.

Abstract: "The uranium content of badly contaminated uranium solutions may be determined quickly using visual comparison methods to an accuracy of [...]. This accuracy may be considerably improved by employing the fluorimeter herein described. Interfering ions and their removal using liquid-liquid extractions are considered."

The operation of the Fast Reactor is considered in terms of normal equilibrium conditions and normal shut-down. The proposed loading, control rod adjustment and subsequent "floating" operation are discussed. Safety devices and interlocks are described. Temperature and reactivity changes are examined with respect to various system failures, phase changes, and "flashing" of the reactor. Slow changes due to faulty slug cooling are also considered. The calculations were initially based upon 10 kw operation. Performance tests of the mercury system now indicate that 20-kw operation may be feasible.

The fission and spallation reactions caused in uranium by bombardment with high energy protons (340 to 350 Mev) were investigated. The reaction products were separated from the target by chemical processes and identified by their radioactive properties. The relative yields of the observed fission products were measured, and the results plotted as a function of mass number. Several of the spallation products were identified and their yields estimated.

Abstract:"The creep resistance of various uranium binary alloys was investigated at 1500 and 1800 F in vacuum. Tests were made on alloys of uranium with beryllium, columbium, molybdenum, tantalum, titanium, and zirconium and on molybdenum-UO2 composites. Of the alloys examined, those of the uranium-molybdenum system exhibited the best creep resistance. At 1500 F, creep rates of about 0.005%/hr were produced in uranium-molybdenum alloys by a stress of 2500 psi and, at 1800 F, similar creep rates were obtained in composites of 90 wt % molybdenum-10 wt % UO2 by a stress of 12,000 psi."

The remodeling, fabrication, and instrumentation of a high vacuum system are described. The faults encountered with the old system and their solution are outlined. Tests were made on diffusion pump oils and on the reduction of pump oil back diffusion. The measurement of high vacuum pressures by a cold cathode ionization gage at various points on a vacuum system are discussed.

Report discussing the effects of thermal diffusion length and certain details in the design of light water moderated reactors and their effect on reactivity.

Abstract: A visualized electron beam has been reflected by a conventional magnetic mirror. Visualization of the beam path from the electron gun to and including the region of reflection was achieved by the "thread ray" technique of Wehnelt. The total current passing through a magnetic mirror has been measured as a function of the beam energy and angular momentum for H₂ over a range of pressures from 0.5 to 5 microns.

Thesis discussing the relative yield of neutral pions from elements in a reaction "as a function of the quantum-limit energy (the maximum energy of the quanta in the bremsstrahlung beam) of the Berkeley synchrotron." Interpretation of the results leads to values for the mean free path for absorption of the neutral pions in nuclear matter.

Report discussing studies regarding properties of the zirconium-uranium epsilon phase related to stability and existence range. Data showing this phase's thermodynamic stability is presented as well as the zirconium-uranium constitutional diagram. Oxygen and nitrogen effects on zirconium-uranium alloys and epsilon-phase alloys is included as well as ternary zirconium-uranium-oxygen diagrams.

Results of previous toroid tests with 28 micro 1600 fired ThO2 spheres are analyzed. Four possible explanations for the essentially zero attack rates are offered and discussed: peculiar motion of toroids or some unknown wall effect; rotational hydrodynamic forces cushioning the particle impact; the bed was not in suspension and not sliding over the walls of the toroid; round particles are not as erosive to oxide film surface as sharp pointed particles.

The following report describes a gaseous scintillation counting system, including the production and operation of the counter.

Available knowledge of precision limits in S.S. accountability measurements and/or calculations by reactor and chemical processing groups is surveyed and summarizes. Experience in comparisons of reactor (production and research) calculations versus chemical plant accountability measurements is also reported. A general tentative conclusion is that available precisions (+/- 0.54 to +/- 0.78% ) in chemical plant measurements is also reported. A general tentative conclusion is that available precisions (+/- 1.0 to +/- 11.0%) possible by calculations (nuclear and/or engineering) of power reactor systems; however, with operation and empirical experience (e.g. less than +/-1.0%

Introduction: "It is the purpose of this note to describe the construction and operation of the plasma injectors used in the magnetic high compression experiments in progress at the Lawrence Radiation Laboratory at Livermore. As the investigations of these injections is still in progress, remarks concerning their operation or the characteristics of the injected plasma are of a tentative nature."

Volstility Pilot Plant Mark III Fluorinator will be a double-chamber type vessel, each chamber 2-1/2ft. by 16in. o.d. separated by a 5 in. pipe 15 in. long. ASME flanged and dished heads will be used for the chamber tops and conical sections with a 60º apex angle for the chamber bottoms. A new furnace designed to maintain the complete lower chamber (molten salt + freeboard) above melt temperature will eliminate past experiences of salt solidification on the wall, heads, and in or on the internal process lines. External pipe runs will be sutoresistance heated to allow melting and drain back of salt plugs. The upper chamber serves as a gas de-entrainment and solids precipitation device to retain most of the entrained salt and condensable fluorides in the 100-400°C temperature range.

From abstract: "Electrical measurements have been made on CaB6, SrB6, BaB6, YB2, YB4, YB6, and YB12 for the purpose of testing models of the electronic structure of the boron atoms in the four boride types represented. The compounds CaB6, SrB6, and BaB6 were found to be semiconductors. The Hall coefficients of YB4 was also measured, but could not be interpreted because the free electron theory does not provide a theoretical value for comparison with experiment. The results are in agreement with the models proposed."

From introduction: "This brief paper deals with the subject of radial temperature differences for heat transfer to fluids flowing through concentric annuli under the following conditions and assumptions: a. constant heat flux; b. fully-established turbulent flow; c. heat transfer through inner wall only; d. physical properties independent of temperature."