"Adjustable cowling flaps, an adjustable-length cowling skirt, and a bottom opening with adjustable flap were tested as means of controlling the rate of cooling-air flow through an air-cooled radial-engine cowling. The devices were tested in the NACA 20-foot tunnel on a model wing-nacelle-propeller combination, through an airspeed range of 20 to 80 miles per hour, and with the propeller blade angle set 23 degrees at 0.75 of the tip radius. The resistance of the engine to air flow through the cowling was simulated by a perforated plate" (p. 1).

Report presenting an analysis and simple method to help solve the problem of assisting the take-off of an airplane by means of auxiliary jet propulsion by determining the jet thrust and weight of jet fuel required to provide a desired reduction in take-off distance or increase in pay load or fuel load for a fixed take-off distance. The use of previous experimental work to verify the analysis is also provided.

"The flow of a compressible fluid past a sphere fixed in a uniform stream is calculated to the third order of approximation by means of the Janzen-Rayleigh method. The velocity and the pressure distribution over the surface of the sphere are computed and the terms involving the fourth power of the Mach number, neglected in Rayleigh's calculation, are shown to be of considerable importance as the local velocity of sound is approached on the sphere. The critical Mach number, that is, the value of the Mach number at which the maximum velocity of the fluid past the sphere is just equal to the local velocity of sound, is calculated for both the second and the third approximation and is found to be, respectively, Mcr=0.587 and Mcr=0.573" (p. 1).

The disturbance imparted to water by a planing body give rise to a wave form of motion on the free surface, the length of the waves increasing indefinitely with increase in the Froude number and being directly proportional to the latter in the case of the plane or two-dimensional problem. At large Froude numbers the effect of the weight shows up to any appreciable extent only at some distance from the body, so that the flow near the body can be considered as part of a flow of an infinitely extending weightless fluid. This paper is a consideration of these characteristics as well as a formulation of the planing problem and its relation to the problem of a thin wing.

Pressure-distribution tests of an NACA 0009 airfoil with an 80-percent-chord plain flap and three plain tabs, having chord of 10, 20, and 30 percent of the flap chord, were made. Section data suitable for application to the design of horizontal and vertical tail surfaces were obtained. Resultant-pressure diagrams for the airfoil with the flap and the 20-percent-chord tab are presented. Plots are also given of increments of normal-force and hinge-moment coefficients for the airfoil, the flap, and the three tabs. A comparison of some characteristic slopes for the 30-, the 50-, and the 80-percent-chord flaps, tested in the general investigation of plain flaps for control surfaces, is included. Section aerodynamic and load data have been made available for a wide range of flap and a tab chords to be used on an NACA 0009 airfoil or on other conventional sections.

From Summary: "Pressure-distribution tests of an NACA 0009 airfoil with a 30-percent-chord plain flap and three plain tabs, having chords 10, 20, and 30 percent of the flap chord, were made. The purpose of these tests was to continue an investigation to supply structural and aerodynamic section data that may be applied to the design of horizontal and vertical tail surfaces. The results are presented as diagrams of resultant pressures and of resultant-pressure increments for the airfoil with the flap and the 20-percent-chord tab. Increments of normal-force and hinge-moment coefficients for the airfoil, the flap, and the three tabs are also given. At all unstalled flap and tab deflections, the experimental distributions agree well with those calculated by an analytical method. The agreement is poor, however, then the stalled or the unstalled condition of the flap or tab deflected alone was changed to an unstalled or stalled condition by the simultaneous deflection of both the flap and the tab."

In the solution of a number of problems on the stability and controllability of airplanes, there arises the necessity for knowing the characteristics of the tail surfaces of the types in common use today. Of those characteristics, the most important are the effectiveness and hinge moments of the tail surfaces. As has been shown in the present paper, there exists the possibility of determining these characteristics by the formulas obtained with a degree of accuracy sufficient for the purposes of preliminary computation.

Aerodynamic force tests of an NACA 23018 airfoil with a Gwinn flap having a chord 25 percent of the overall chord and of an NACA 23015 airfoil with a plain flap having a 25-percent chord were conducted to determine the relative merits of the Gwinn and the plain flaps. The tests indicated that, based on speed-range ratios, the plain flap was more effective than the Gwinn flap. At small flap deflections, the plain flap had lower drag coefficients at lift-coefficient values less than 0.70. For lift coefficients greater than 0.70, however, the Gwinn flap at all downward flap deflections had the lower drag coefficients.

Report presents the results of a full-scale investigation conducted in the NACA 20-foot tunnel to determine the pressure difference available for cooling with cowling flaps. The flaps were applied to an exit slot of smooth contour at 0 degree flap angle. Flap angles of 0 degree, 15 degrees, and 30 degrees were tested. Two propellers were used; propeller c which has conventional round blade shanks and propeller f which has airfoil sections extending closer to the hub. The pressure available for cooling is shown to be a direct function of the thrust disk-loading coefficient of the propeller.

A pressure-distribution investigation has been conducted in the NACA 4 by 6-foot vertical wind tunnel to determine the air loads on an NACA 23012 airfoil in combination with a 25.66-percent-chord slotted flap and a 20-percent-chord split flap. Pressures were measured on both the upper and the lower surfaces of the main airfoil and the flaps for several angles of attack and at several flap settings. The data, presented as pressure diagrams and as graphs of the section coefficients for the flap alone and for the airfoil-flap combinations, are applicable to rib and flap design for a combination of a thick airfoil and a slotted or a split flap. The results of previous tests of a NACA 23012 airfoil with a slotted flap are compared with the present results.

"A method is presented of comparing the performance, weight, and general dimensional characteristics of inter-coolers. The performance and dimensional characteristics covered in the comparisons are cooling effectiveness, pressure drops and weight flows of the charge and cooling air, power losses, volume, frontal area, and width. A method of presenting intercooler data is described in which two types of charts are plotted; (1) A performance chart setting forth all the important characteristics of a given intercooler and (2) a replot of these characteristics for a number of intercoolers intended to assist in making a selection to satisfy a given set of installation conditions" (p. 1).

A chart is presented for the values of the coefficient in the formula for the critical compressive stress at which buckling may be expected to occur in flat rectangular plates supported along all edges and, in addition, elastically restrained against rotation along the unloaded edges. The mathematical derivations of the formulas required in the construction of the chart are given.

Report presenting testing of preformed copper fins which were furnace-brazed to a steel-cylinder barrel. The barrel was electrically heated and blower-cooled to determine heat overall heat-transfer coefficient. Information regarding potential future adaptations of the fins are provided.

In this report it will be seen that the piston speed - as, moreover, any other speed, such as bearing velocity - must be independent of the quantity dimensions and must be a representative quantity similar to the high speed and the specific weight per horsepower.

Report presenting an investigation of the effects of propeller operation on pitching moments with particular reference to the effect of propeller forces, the field of flow in the slipstream, and the increments of lift on the wing and the tail. A procedure, directly applicable only to single-engine monoplanes without flaps, has been set up for predicting the effect of propeller operation on pitching moments as well.

Report presenting testing to determine the boundary layer characteristics and profile drag of the NACA 35-215 airfoil section at high Reynolds numbers. The results indicated that a forward movement of the transition point occurred at about 3 percent of the chord due to operation of the engines and propellers.

The power and heat-stress conditions of geometrically similar engines are discussed. The advantages accruing from smaller cylinder dimensions are higher specific horsepower, lower weight per horsepower, lower piston temperature, and less frontal area, with reduced detonation tendency.

"The Pratt and Whitney Aircraft company and the Naval Aircraft Factory of the United States Navy cooperated in a laboratory and flight program of tests on an exhaust turbine supercharger. Two series of dynamometer tests of the engine super-charger combination were completed under simulated altitude conditions. One series of hot gas-chamber tests was conducted by the manufacturer of the supercharger" (p. 1).

Some of the problems considered in this report include: thermodynamics of surface friction, application of thick wing sections, special applications of controllable propellers, and gas turbines for aircraft.

A sturdy stiffener is defined as a stiffener of such proportions that it does not suffer cross-sectional distortion when moments are applied to some part of the cross section. When such a stiffener is attached to one edge of a plate, it will resist rotation of that edge of the plate by means of its torsional properties. A formula is given for the restraint coefficient provided the plate by such a stiffener. This coefficient is required for the calculation of the critical compressive stress of the plate.

"Concurrent tests were performed on a 1/16 and a 1/20 scale model (wing spans of 2.64 and 2.11 ft. respectively) of a modern low wing monoplane in the NACA 15 foot free-spinning wind tunnel. Results are presented in the form of charts that afford a direct comparison between the spins of the two models for a number of different conditions. Qualitatively, the same characteristic effects of control disposition, mass distribution, and dimensional modifications were indicated by both models" (p. 1).

Note presenting testing performed on scale models of a modern low-wing monoplane in the 15-foot free-spinning wind tunnel. Results are presented in the form of charts that afford a direct comparison between the spins of the two models for a number of different conditions. The results indicate that, within the range of Reynolds numbers used in the present investigation, such factors as difficulty of ballasting and testing are more important in determining proper model size than the changes in scale effect likely to result from the use of different sizes of models.

Note presenting tests made on cylindrical and spherical shells to determine the local stresses and deflections produced by concentrated and variously distributed loading. The results are correlated with those of earlier experiments, and empirical formulas based on the data are proposed. Data are presented on the effect of severe prestressing on stiffness and on the efficiency of welded lugs of various forms in transmitting a load to a thin shell without producing excessive local stresses.

"An investigation was made in the NACA 7- by 10-foot wind tunnel to determine the effect of slot-lip location on the aerodynamic section characteristics of an NACA 23012 airfoil with a 30-percent-chord slotted flap. Tests were made with slot lips located at 90 and 100 percent of the airfoil chord and with two different flap shapes. The results are compared with a slotted flap previously developed by the National advisory Committee for Aeronautics with a slot lip located at 83 percent of the airfoil chord. The extension of the slot lip to the rear increased the section lift and pitching-moment coefficients" (p. 1).