Report presenting an investigation to determine the blade torsional deflection of three supersonic-type propellers at various operating conditions. Blade-torsional deflection was found to produce appreciable results that can be predicted by theory with good accuracy. Results regarding the efficiency, thrust coefficient, and power coefficient are provided.

From Summary: "Linearized compressible-flow analysis is applied to the study of wind-tunnel-wall interference for subsonic flow in either two-dimensional or circular test sections having slotted or porous walls. Expressions are developed for evaluating blockage and lift interference."

Report presenting the effect of channel geometry on flame quenching, as calculated on the basis of average active particle chain lengths, is related among six different geometries: plane parallel plates of infinite extent, cylindrical tubes, rectangular slots, cylindrical annuli, and tubes of elliptical and equilaterally triangular shape. The results indicated that the observed variation of flame quenching as a function of quenching geometry may be successfully predicted for a range of pressures and for rich as well as lean propane-air flames.

Memorandum presenting an investigation of the performance of inlet configurations with a forebody designed for isentropic external compression at a nominal Mach number of 5.6. At zero angle of attack, all the configurations yielded larger total-pressure recoveries than had previously been obtained with a single-conical-shock inlet. Results regarding the flow about the forebody, inlet performance, and performance comparisons are provided.

Memorandum presenting an investigation of the performance of inlet configurations with a forebody designed for isentropic external compression at a nominal Mach number of 5.6. At zero angle of attack, all of the configurations yielded larger total-pressure recoveries than had previously been obtianed with a single-conical-shock inlet. Results regarding the flow about the forebody and performance comparisons are provided.

"Results are reported of current studies at the Forest Products Laboratory to develop a metal-bonding adhesive with greater resistance to temperatures up to 600 degrees Fahrenheit that is easier to use than present ones. Most promising is a formulation of phenol and epoxy resins modified with hexamethylenetetramine and supplied for use as a dry tape supported on a glass-mat base" (p. 1).

Report presenting flight measurements of the buffeting characteristics of the Bell X-5 airplane at 58.7 degrees of sweepback at a range of Mach numbers and altitudes. Information about tail buffeting and wing buffeting at several angles of attack is provided. The pilot considered the buffeting to be unobjectionable throughout the entire test region.

From Summary: "The presence of radomes and instruments that are sensitive to water films or ice formations in the nose section of all-weather aircraft and missiles necessitates a knowledge of the droplet impingement characteristics of bodies of revolution. Because it is possible to approximate many of these bodies with an ellipsoid of revolution, droplet trajectories about an ellipsoid of revolution with a fineness ratio of 10 were computed for incompressible axisymmetric air flow. From the computed droplet trajectories, the following impingement characteristics of the ellipsoid surface were obtained and are presented in terms of dimensionless parameters: (1) total rate of water impingement, (2) extent of droplet impingement zone, and (3) local rate of water impingement."

Report presenting an experimental investigation to determine the effect of several wedge-type boundary-layer diverters on drag and inlet pressure recovery in the 8- by 6-foot supersonic wind tunnel at Mach numbers of 1.5, 1.8, and 2.0. The model consisted of two rectangular ramp-type inlets mounted on the NACA RM-10 body of revolution. Results regarding variation of inlet pressure recovery and configuration drag with inlet mass-flow ratio, changes in the shock pattern off the inlet ramp, pressure-recovery-mass-flow characteristics, and drag coefficients are provided.

Report presenting an exploratory investigation of three aluminum disoaps of C(sub 8) acids to determine the gelling properties and stabilizing ability in slurries of 50 percent magnesium power and JP-4 fuel. All of the soaps were found to gel the slurries satisfactorily and to exhibit adequate reproducibility of gel properties. Results regarding the soap behaviors, effects of temperature, viscosity, and formation of the gel structures are provided.

Report presenting an investigation in a mixing-zone apparatus to determine the effects of jet flow on two-dimensional base pressure and the development of supersonic channel flow about a two-dimensional base, with and without splitter plates of different thicknesses. Results regarding the starting cycle for outer streams only, the fully established supersonic flow, and the base pressure between the center jet and outer streams are provided.

Report presenting a linearized theoretical analysis made to determine minimum-wave-drag airfoil sections for arrow wings having the same airfoil sections at all spanwise sections. Numerical computations of the airfoil shape and wing wave drag were performed for a delta wing and an arrow wing with a ratio of the tangent of the trailing-edge sweep angle to the tangent of the leading-edge sweep angle of 0.4.

Memorandum presenting an investigation of the effect of the addition of approximately 6 percent nickel, cobalt, or platinum on some properties of molybdenum disilicide. These additions resulted in appreciably lowering the modulus-of-rupture strength from that of unalloyed molybdenum disilicide. Results regarding density and particle-size analysis, chemical analysis of bars, metallographic and x-ray analysis, density and resistivity, modulus-of-rupture strengths, thermal shock tests, and oxidation resistance are provided.

Note describing the preparation and evaluation of 25 binary and ternary alloys with liquidus temperatures in the range of 2000 to 2500 degrees Fahrenheit as part of an investigation of potential brazing alloys for molybdenum for use at elevated temperatures. Three commercial alloys were also investigated.

Report presenting a method for determining the lateral-stability derivatives, transfer-function coefficients, and the modes for lateral motion from frequency-response data for a rigid aircraft. The method is based on the application of the vector technique to the equations of lateral motion, so that the three equations of lateral motion can be separated into six equations. Two numerical examples are given to demonstrate the use of the method.

"The performance of liquid fluorine and liquid ammonia as a propellant combination was evaluated in 1000-pound-thrust rocket engines operated at a chamber pressure of 600 pounds per square inch absolute. Values of specific impulse, characteristic velocity, thrust coefficient, and heat rejection were obtained as functions of propellant mixture ratio for each of four injectors: a triplet, a showerhead, and two like-on-like types" (p. 1).

Report presenting an investigation of fuel injection into a combustion chamber, including theoretical and experimental results regarding the unsteady-state portion of the total vaporization time of single fuel droplets injected into air.

Report presenting an investigation at high subsonic speeds of a complete model with one of four types of wings: a basic sweptback wing, an M-shaped wing, a W-shaped wing, and a cranked wing. All of the wings had the same aspect and taper ratio and were tested at the same range of Mach numbers. Results regarding longitudinal characteristics and lateral characteristics of the different wings are provided.

Sea-level static testing of turbojet engine afterburner.

Report presenting a sea-level static investigation to determine the performance and some design principles for a short afterburner. The power section of a 12-stage axial-flow turbojet engine was used and the afterburner was designed to fit within the length required for the tail pipe used on the standard nonafterburning model.

"A considerable weight reduction in the turbine wheel of an aircraft gas turbine is attained through the use of high-aspect-ratio rotor blading. An experimental investigation was made to compare the performance of a turbine of conservative aerodynamic design having shrouded rotor blades with an aspect ratio of 4.48 with that obtained from both a shrouded and an unshrouded rotor design with aspect ratio of 2.24. The use of high-aspect-ratio rotor blades had a negligible effect on the turbine efficiency" (p. 1).

Report presenting an investigation of a conservatively designed experimental cold-air turbine with and without a shroud band on the rotor blades. The tip of the rotor blade was oriented toward the tangential direction so that the adverse effect of blade-tip scraping would not be appreciable. The efficiency for the unshrouded-rotor configuration was about one point higher than for the shrouded rotor.

Report presenting an investigation to study the aerodynamic problems associated with a turbine design for a mode of engine operation which utilizes turbine stator adjustment to maintain a fixed compressor operating point. An indication of the turbine requirements for a particular compressor operating point indicated that a feasible sing-stage air-cooled turbine design could be obtained within reasonable aerodynamic limits. Results regarding the performance of the turbine, pressure ratios, and operational requirements are provided.

Memorandum presenting a study of the ignition of ammonia and mixed oxides of nitrogen at 160 degrees Fahrenheit made with and without fuel additives utilizing small-scale rocket engines of approximately 200 pounds thrust. All experiments were conducted at sea-level pressures except two at a range of pressure altitudes. Results regarding the use of lithium as a catalyst, calcium as a catalyst, and no apparent catalyst are provided.