Report presenting tests on a scale model of a four-engine transport airplane to determine the stability characteristics, empennage control-surface effectiveness, the effect of propeller rotation on longitudinal stability, and a method for carrying spare wing panels under the fuselage. The effect of two models of wing power operation on the characteristics of the model was studied. The results indicate that the model possess satisfactory stick-fixed longitudinal stability for all normal flight conditions except for high power with flaps extended.

"Values of the circulation function have been obtained for dual-rotating propellers. Numerical values are given for four, eight, and twelve-blade dual-rotating propellers and for advance ratios from 2 to about 6. In addition, the circulation function has been determine for single-rotating propellers for the higher values of the advance ratio. The mass coefficient, another quantity of significance in propeller theory, has been introduced" (p. 35).

"The results of measurements in the Langley full-scale tunnel of the maximum lift coefficients and stalling characteristics of airplanes have been collected. The data have been analyzed to show the nature of the effects on maximum lift and stall of wing geometry, fuselages and nacelles, propeller slipstream, surface roughness, and wing leading-edge appendages such as ducts, armaments, tip slats, and airspeed heads. Comparisons of full-scale-tunnel and flight measurements of maximum lift and stall are included in some cases, and the effects of the different testing techniques on the maximum-lift measurements are also given (p. 1)".

Field measurements were made on a fighter airplane to determine the approximate magnitude of the horizontal tail loads in accelerated flight. In these flight measurements, pressures at a few points were used as an index of the tail loads by correlating these pressures with complete pressure-distribution data obtained in the NACA full-scale tunnel. In addition, strain gages and motion pictures of tail deflections were used to explore the general nature and order of magnitude of fluctuating tail loads in accelerated stalls.

"Field measurements were made on a fighter airplane to determine the approximate magnitude of the horizontal tail loads in accelerated flight. In these flight measurements, pressures at a few points were used as an index of the tail loads by correlating these pressures with complete pressure-distribution data obtained in the NACA full-scale tunnel. In addition, strain gages and motion pictures of tail deflections were used to explore the general nature and order of magnitude of fluctuating tail loads in accelerated stalls" (p. 351).

"A method is presented for predicting the amplitude and frequency, under certain simplifying conditions, of the hunting oscillations of an automatically controlled aircraft with lag in the control system or in the response of the aircraft to the controls. If the steering device is actuated by a simple right-left type of signal, the series of alternating fixed-amplified signals occurring during the hunting may ordinarily be represented by a "square wave." Formulas are given expressing the response to such a variations of signal in terms of the response to a unit signal" (p. 487).

From Introduction: "The present paper deals with control surfaces having plain-overhang and Frise balances."

From Introduction: "As a part of the general lateral-control investigation by the NACA, the large amount of two- and three-dimensional data on the rolling effectiveness of ailerons without exposed overhang balance is collected and analyzed in the present paper."

From Summary: "This paper deals with the single problem if circular shell-supported frames subjected to concentrated loadings. A mathematical attack is developed and presented in the form of nondimensional-coefficient curves."

From Summary: "The results of an analytical investigation to determine the qualitative effects of elevator-fabric distortion on the stick-force characteristics of an airplane are presented. These results indicate that serious alteration of intended stick-force characteristics can be produced by elevator-fabric distortion."

Report presenting a device that automatically analyses the data from a 45 degree strain rosette. The rosette strains are properly combined by means of an electric circuit to yield a direct meter reading of maximum shear strain and major and minor principal strains.

Report discusses an analysis and preliminary design of a control linkage that varies automatically with dynamic pressure. The advantages of the device, including greater lateral control than a fixed control linkage without additional aerodynamic balance, are detailed. The effect of variable linkage on lateral-control characteristics is also described.

From Summary: "Charts are presented for rapidly determining the principal strains and stresses, the maximum shear strain and stress, and the orientation of principal axes from data on 45 degree strain rosettes. The charts may be used for analyzing the conventional data consisting of strains measured along three gage lines 45 degrees apart, but their application is more direct if the rosette data are obtained by means of special circuits that require the use of four gages 45 degrees apart."

Report presenting an investigation of the cooling of a Franklin 6-AC-29S horizontally opposed cylinder air-cooled engine installed in a Fleetwings model 33 trainer. The cowling on the airplane did not provide satisfactory cooling, but several alterations were tested, including with cylinder baffles. Results regarding engine cooling, aerodynamics of the cowling installation, and predicted versus actual cowling performance are provided.

"The effects of changes in aileron rigging between 2 deg up and 2 deg down on the stick forces were determined from wind-tunnel data for a finite-span wing model. These effects were investigated for ailerons deflecting equally in both directions and linearly with stick deflection. Data were analyzed for a Frise, a sealed internally balanced, and a beveled-trailing-edge aileron" (p. 1).

"The results of a series of tests to determine the effect of internal pressure on the buckling load of a thin cylinder under an applied torque indicated that internal pressure raises the shear buckling stress. The experimental results were analyzed with the aid of previously developed theory and a simple interaction formula was derived" (p. 1).

"The effect on static-pressure measurements of locating a pitot-static tube 0.55 chord ahead of an airfoil section has been investigated. The tests were conducted in the NACA 24-inch high-speed tunnel on airfoil sections of various thickness ratios over a large range of Mach number. The results show that for a wing having a thickness ratio of 0.15 the measured Mach number, determined from a pitot-static-tube reading, is approximately 0.01 too low at a stream Mach number of 0.4 and approximately 0.03 too low at a Mach number of 0.8" (p. 1).

Report discusses the "effects of oil introduced into the combustion chamber and of oil-spray piston cooling on the knock-limited performance of aircraft engines" (from Summary). A CFR engine and Allison V-1710 cylinder were used to test the rate of oil consumption, knock, and knock-limited brake mean effective pressure.

Report presenting methods for estimating pressure distributions over protuberances such as cockpit canopies, gun turrets, blisters, scoops, and sighting domes. The methods are applied to the estimation of the pressure distributions over spherical segment and faired gun turrets and over the protuberances on the Brewster SB2A-1 airplane. The effects of compressibility, interference, and flow separation are discussed.

"An experimental investigation of rectangular exhaust-gas ejector pumps was conducted to provide data that would serve as a guide to the design of ejector applications for aircraft engines with marginal cooling. The pumping characteristics of rectangular ejectors actuated by the exhaust of a single-cylinder aircraft engine were determined for a range of ejector mixing-section area from 20 to 50 square inches, over-all length from 12 to 42 inches, aspect ratio from 1 to 5, diffusing exit area from 20 to 81 square inches, and exhaust-nozzle aspect ratio from 1 to 42" (p. 161).

Report includes tension fatigue test results on the following types of samples of 0.040-inch alclad 24s-t: (1) monoblock sheet samples as received and after a post-aging heat treatment, (2) "sheet efficiency" samples (two equally stressed sheets joined by a single transverse row of spot welds) both as received and after post-aging, (3) spot-welded lap-joint samples as received and after post-aging, and (4) roll-welded lap-joint samples. (author).

Report discusses measurements of the relaxation time of steam and nitrogen due to their importance as turbine-working fluids. Additional calculations regarding different nozzle lengths are included.

Report presenting the results of tests of a circular fuselage with various combinations of tail lengths and vertical tail surfaces with and without the horizontal tail surface in the 6- by 6-foot test section of the stability tunnel in the form of diagrams of variation of coefficients of lateral force and yawing moment with angle of yaw and angle of attack.

Report presenting an investigation to determine the knock-limited performance in a full-scale aircraft-engine cylinder of leaded blends of 10 pure hydrocarbons and a base fuel.