From Introduction: "This paper presents the results of the investigation of the wing alone and of the wing-fuselage configurations employing a wing with an unswept quarter-chord line, aspect ratio 4, taper ratio 0.6, and an NACA 65A004 airfoil section parallel to the air stream. The experimental results of a wing of identical plan from having an NACA 65A006 airfoil section which was tested as part of the transonic program are presented in reference 1.

Report presenting an investigation concerned with the measurement of the characteristics of longitudinal-control devices for a wing-fuselage combination with a wing with the leading edge swept back 63 degrees. Most of the investigation was devoted to testing a 30-percent-chord, 50-percent-semispan elevon, but some used upper-surface spoilers. Results regarding the characteristics of the wing with the elevon undeflected and control-surface effectiveness are provided.

Report presenting an experimental investigation to determine the aerodynamic load distributions of a series of five bodies with conical or slightly blunted noses and cylindrical afterbodies in the 1- by 1-foot supersonic wind tunnel. Pressure distributions and viscous drags were measured at Mach number 3.12 for a range of Reynolds numbers and angles of attack.

"An investigation was conducted at Mach number 1.90 to determine pressure recovery and mass-flow characteristics of series of perforated convergent-divergent supersonic diffusers. Pressure recoveries as high as 96 percent were obtained, but at reduced mass flows through the diffuser. Theoretical considerations of effect of perforation distribution on shock stability in converging section of diffuser are presented and correlated with experimental data. A method of estimating relative importance of pressure recovery and mass flow on internal thrust coefficient basis is given and a comparison of various diffusers investigated is made" (p. 1).

Memorandum presenting lift and drag characteristics that have been determined in flight in the landing-approach configuration on 41 jet-propelled fighter-type airplane arrangements, including various wing boundary-layer-control installations. Minimum comfortable approach speeds for carrier-type landings were evaluated for these airplanes by four test pilots. Results regarding the presentation of data, methods for the prediction of minimum comfortable approach speed, reasons for limiting approach speed, comparison of flight and predicted approach speeds, and comparison of test pilots' and service pilots' approach speed are provided.

Report presenting lift and drag characteristics in the landing-approach configuration on 41 jet-propelled fighter-type airplane arrangements using flight testing. Minimum comfortable approach speeds were evaluated by four test pilots. Suggestions for achieving optimal speeds for approach under various conditions are also provided.

From Summary: "An empirically derived basis for predicting the area, rate, and distribution of water-drop impingement on airfoils of arbitrary section is presented. The concepts involved represent an initial step toward the development of a calculation technique which is generally applicable to the design of thermal ice-prevention equipment for airplane wing and tail surfaces. It is shown that sufficiently accurate estimates, for the purpose of heated-wing design, can be obtained by a few numerical computations once the velocity distribution over the airfoil has been determined. The calculation technique presented is based on results of extensive water-drop trajectory computations for five airfoil cases which consisted of 15-percent-thick airfoils encompassing a moderate lift-coefficient range."

Report presenting an experimental two-dimensional investigation of the mechanism of the flow and losses involved in the operation of a low-solidity highly loaded turbine-blade profile suitable for use in an air-cooled turbine, which has been made in a cascade.

Field measurements were made on a fighter airplane to determine the approximate magnitude of the horizontal tail loads in accelerated flight. In these flight measurements, pressures at a few points were used as an index of the tail loads by correlating these pressures with complete pressure-distribution data obtained in the NACA full-scale tunnel. In addition, strain gages and motion pictures of tail deflections were used to explore the general nature and order of magnitude of fluctuating tail loads in accelerated stalls.

"Field measurements were made on a fighter airplane to determine the approximate magnitude of the horizontal tail loads in accelerated flight. In these flight measurements, pressures at a few points were used as an index of the tail loads by correlating these pressures with complete pressure-distribution data obtained in the NACA full-scale tunnel. In addition, strain gages and motion pictures of tail deflections were used to explore the general nature and order of magnitude of fluctuating tail loads in accelerated stalls" (p. 351).

Report presenting testing of two blunt-nose models, a flat-face-cone and a hemisphere-cone, at Mach numbers up to 4.7. The main purpose was to determine information about heating rates and transition for different blunt nose shapes for long-range ballistic missiles. Information about pressure measurements and heat transfer is provided.

Memorandum presenting results of tests for possible flutter of a dynamically and elastically scaled model of a proposed all-movable horizontal tail surface for the North American X-15 airplane. Tests at Mach number 6.86 were made on the scaled model and on several other configurations with lower stiffnesses.

"Results of tests for possible flutter of a dynamically and elastically scaled model of a proposed all-movable horizontal tail surface for the North American X-15 airplane are presented herein. Tests at a Mach number of 6.86 were made on the scaled model and on several other configurations having lower stiffness. Flexibility influence coefficients and calculated modes and frequencies for the weakest configuration are presented" (p. 1).

Memorandum presenting an investigation to determine the performance of the XJ79-GE-1 turbojet engine and its components, while operating as integral parts of the engine, conducted in an altitude test chamber. Data were obtained over a range of Reynolds number indices and for various settings of the variable compressor stators and variable-area exhaust nozzle from fully open to fully closed positions. Results regarding the component performance and engine performance are provided.

Report presenting sound measurements at static conditions for a two-blade, 47-inch-diameter propeller over a range of tip Mach numbers. For comparison, spectrums have been obtained at both subsonic and supersonic tip speeds. Results regarding the experimental results and comparison with theory are provided.

Report presenting testing of four multiweb wing models were tested at Mach number 2 in a free jet to investigate structural effects of aerodynamic heating and loading. All of the models were the same except for the number of chordwise internal stiffening ribs; each had zero, one, two, or three. Results regarding laboratory vibration tests, jet tests, model behavior, temperatures, stresses, and discussion of failure are provided.

Report discussing a study of automatic nonreturn air valves for use in an intermittent-jet engine. Four valve-spring materials, three valve-grill materials, and five types of valves were used. Valve A, which was made out of aluminum, was found to perform the best and last the longest.