This conference paper describes the electronic properties of ZnO/CdS/Cu(In,Ga)Se2 (CIGS)/Mo/SLG polycrystalline thin-film solar cells with compositions ranging from Cu-rich to In-rich were investigated by deep level transient spectroscopy and capacitance-voltage (C-V) measurements. This compositional change represents the evolution of the film during growth by the three-stage process. Four thin-film CIGS samples with different Cu content were obtained. The Cu/(In+Ga) ratio ranges from 1.24 (Cu-rich)to 0.88 (In-rich), whereas the Ga/(In+Ga) ratio ranges from 0.19 (Cu-rich)to 0.28 (In-rich).The Cu-rich sample exhibits a shallow majority-carrier trap with an activation energy of 0.12 eV and another deeper trap with an activation energy of 0.28 eV, whereas the In-rich sample has a shallow minority-carrier trap with an activation energy of 0.12 eV. The two samples show evidence of a deeper trap at higher temperature. C-V measurements showed that the average carrier concentration (N values) around the junction of the cell changed as the film transitions from Cu-rich to In-rich. DLTS shows that acceptor-like traps are dominant in samples where CIGS grains did not go through the Cu-rich to In(Ga)-rich transition. While donor-like traps are dominant in the In(Ga)-rich samples.

Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen or ambient-temperature compressed hydrogen. This flexibility results in multiple advantages with respect to compressed hydrogen tanks or low-pressure liquid hydrogen tanks. Our work is directed at verifying that commercially available aluminum-lined, fiber-wrapped pressure vessels can be safely used to store liquid hydrogen. A series of tests have been conducted, and the results indicate that no significant vessel damage has resulted from cryogenic operation. Future activities include a demonstration project in which the insulated pressure vessels will be installed and tested on two vehicles. A draft standard will also be generated for certification of insulated pressure vessels.

We are working on developing an alternative technology for storage of hydrogen or natural gas on light-duty vehicles. This technology has been titled insulated pressure vessels. Insulated pressure vessels are cryogenic-capable pressure vessels that can accept either liquid fuel or ambient-temperature compressed fuel. Insulated pressure vessels offer the advantages of cryogenic liquid fuel tanks (low weight and volume), with reduced disadvantages (fuel flexibility, lower energy requirement for fuel liquefaction and reduced evaporative losses). The work described in this paper is directed at verifying that commercially available pressure vessels can be safely used to store liquid hydrogen or LNG. The use of commercially available pressure vessels significantly reduces the cost and complexity of the insulated pressure vessel development effort. This paper describes a series of tests that have been done with aluminum-lined, fiber-wrapped vessels to evaluate the damage caused by low temperature operation. All analysis and experiments to date indicate that no significant damage has resulted. Future activities include a demonstration project in which the insulated pressure vessels will be installed and tested on two vehicles. A draft standard will also be generated for obtaining insulated pressure vessel certification.

The diverse set of organizations and software components involved in a typical collaboratory make providing a seamless security solution difficult. In addition, the users need support for a broad range of frequency and locations for access to the collaboratory. A collaboratory security solution needs to be robust enough to ensure that valid participants are not denied access because of its failure. There are many tools that can be applied to the task of securing collaborative environments and these include public key infrastructure, secure sockets layer, Kerberos, virtual and real private networks, grid security infrastructure, and username/password. A combination of these mechanisms can provide effective secure collaboration capabilities. In this paper, we discuss the requirements of typical collaboratories and some proposals for applying various security mechanisms to collaborative environments.

To enable collaboration on the daily tasks involved in scientific research, collaborative frameworks should provide lightweight and ubiquitous components that support a wide variety of interaction modes. We envision a collaborative environment as one that provides a persistent space within which participants can locate each other, exchange synchronous and asynchronous messages, share documents and applications, share workflow, and hold videoconferences. We are developing the Pervasive Collaborative Computing Environment (PCCE) as such an environment. The PCCE will provide integrated tools to support shared computing and task control and monitoring. This paper describes the PCCE and the rationale for its design.

The US Heavy Ion Fusion Virtual National Laboratory is continuing research into ion sources and injectors that simultaneously provide high current (0.5-1.0 Amps) and high brightness (normalized emittance better than 1.0 {pi}-mm-mr). The central issue of focus is whether to carry on the traditional approach of large surface ionization sources or to adopt a multi-aperture approach that transports many smaller ''beamlets'' separately at low energies before allowing them to merge. For the large surface source, the recent commissioning of the 2-MeV injector for the High Current experiment has increased our understanding of the beam quality limitations for these sources. We have also improved our techniques for fabricating large diameter aluminosilicate sources to improve lifetime and emission uniformity. For the multi-aperture approach we are continuing to study the feasibility of small surface sources and a RF induced plasma source in preparation for beamlet merging experiments, while continuing to run computer simulations for better understanding of this alternate concept. Experiments into both architectures will be performed on a newly commissioned ion source test stand at LLNL called the STS-500. This stand test provides a platform for testing a variety of ion sources and accelerating structures with 500 kV, 17-microsecond pulses. Recent progress …

The Source Injector Program for the US Heavy Ion Fusion Virtual National Laboratory is currently exploring the feasibility of using RF gas plasma sources for a HIF driver. This source technology is presently the leading candidate for the multiple aperture concept, in which bright millimeter size beamlets are extracted and accelerated electrostatically up to 1 MeV before the beamlets are allowed to merge and form 1 A beams. Initial experiments have successfully demonstrated simultaneously high current density, {approx} 100 mA/cm{sup 2} and fast turn on, {approx} 1 {micro}s. These experiments were also used to explore operating ranges for pressure and RF power. Results from these experiments are presented as well as progress and plans for the next set of experiments for these sources.

The US Heavy Ion Fusion Virtual National Laboratory is continuing research into ion sources and injectors that simultaneously provide high current (0.5-1.0 Amps) and high brightness (normalized emittance better than 1.0 {pi}-mm-mr). The central issue of focus is whether to continue pursuing the traditional approach of large surface ionization sources or to adopt a multiaperture approach that transports many smaller ''beamlets'' separately at low energies before allowing them to merge. For the large surface source concept, the recent commissioning of the 2-MeV injector for the High Current eXperiment has increased our understanding of the beam quality limitations for these sources. We have also improved our techniques for fabricating large diameter aluminosilicate sources to improve lifetime and emission uniformity. For the multiaperture approach, we are continuing to study the feasibility of small surface sources and a RF induced plasma source in preparation for beamlet merging experiments, while continuing to run computer simulations for better understanding of this alternate concept. Experiments into both architectures will be performed on a newly commissioned ion source test stand at LLNL called STS-500. This stand test provides a platform for testing a variety of ion sources and accelerating structures with 500 kV, 17-microsecond pulses. Recent progress …

Sealed {sup 252}Cf sources in the microCurie to milliCurie range are routinely used in industry and research. At present, no reliable analytical method is available for precise determination of the activity. Very strong sources can be analyzed by neutron counting but the error is large. The authors propose to use gamma-ray spectroscopy for such analysis. In particular, high-energy gamma rays (above 1 MeV) of fission fragments in equilibrium with the source are very convenient because they have little absorption in materials surrounding the source. They have measured the gamma/alpha ratio for {sup 252}Cf with an uncertainty of better than 5%. The experiment involved the preparation of several thin {sup 252}Cf sources, alpha pulse height analysis, determination of alpha decay rate, and the measurement of gamma singles spectrum with a well shielded germanium spectrometer. The measured ratio and the gamma ray spectroscopy of unknown samples can provide the activity of {sup 252}Cf in these samples.

The Antarctic Muon and Neutrino Detector Array (AMANDA) began collecting data with ten strings in 1997. Results from the first year of operation are presented. Neutrinos coming through the Earth from the Northern Hemisphere are identified by secondary muons moving upward through the array. Cosmic rays in the atmosphere generate a background of downward moving muons, which are about 10{sup 6} times more abundant than the upward moving muons. Over 130 days of exposure, we observed a total of about 300 neutrino events. In the same period, a background of 1.05 x 10{sup 9} cosmic ray muon events was recorded. The observed neutrino flux is consistent with atmospheric neutrino predictions. Monte Carlo simulations indicate that 90 percent of these events lie in the energy range 66 GeV to 3.4 TeV. The observation of atmospheric neutrinos consistent with expectations establishes AMANDA-B10 as a working neutrino telescope.

This conference paper describes the molybdenum thin films that were deposited on soda lime glass (SLG) substrates using direct-current planar magnetron sputtering, with a sputtering power density of 1.2 W/cm2. The working gas (Ar) pressure was varied from 0.6 to 16 mtorr to induce changes in the Mo films' morphology and microstructure. Thin films of Cu(In,Ga)Se2 (CIGS) were deposited on the Mo-coated glass using the 3-stage co-evaporation process. The morphology of both the Mo-coated SLG and the CIGS thin films grown on it was examined using high-resolution scanning electron microscopy. Na was depth profiled in the Mo and CIGS films by secondary ion mass spectrometry. The device performance was evaluated under standard conditions of 1000 W/m2 and 25 C. Optimum device performance is found for an intermediate Mo sputtering pressure.

Gamma-ray spectroscopy is a valuable tool of science and technology. Many applications for this tool are in need of a detector technology capable of achieving excellent energy resolution and efficient detection while operating at room temperature. Detectors based on the material cadmium zinc telluride (CdZnTe) could potentially meet this need if certain material deficiencies are addressed. The coplanar-grid as well as other electron-only detection techniques are effective in overcoming some of the material problems of CdZnTe and, consequently, have led to efficient gamma-ray detectors with good energy resolution while operating at room temperature. At the present time, the performance of these detectors is mainly limited by the degree of uniformity in electron generation and transport. Despite recent progress in the growth of CdZnTe material, small variations in these properties remain a barrier to the widespread success of such detectors. Alpha-particle response characterization of Cd ZnTe crystals fabricated into simple planar detectors provides an effective tool to accurately study such variations. We have used a finely collimated alpha source to produce two-dimensional maps of detector response. For a number of crystals, a clear correlation has been observed between their alpha response maps and the distribution of tellurium inclusions inside the crystals. …

None

The United States Department of Energy (DOE) continually seeks safer and more cost-effective technologies for use in decontaminating and decommissioning nuclear facilities. To this end, the Deactivation and Decommissioning Focus Area of DOE's Office of Science and Technology sponsors Large-Scale Demonstration and Deployment Projects (LSDDP) to test new technologies. As part of these projects, developers and vendors showcase new products designed to decrease health and safety risks to personnel and the environment, increase productivity, and lower costs. As part of the FY 2000 and 2001 LSDDP, the Idaho National Engineering and Environmental Laboratory (INEEL) collaborated with the Russian Research and Development Institute of Construction Technology (NIKIMT). This collaboration resulted in the development of the Robotic Gamma Locating and Isotopic Identification Device (RGL and IID) which integrated DOE Robotics Crosscutting (Rbx) technology with NIKIMT Russian gamma locating and isotopic identification technology. This paper will discuss the technologies involved in this integration and results from the demonstration including reduction of personnel exposure, increase in productivity, and reduced risk.

Gallium nitride is grown by plasma-assisted molecular-beam epitaxy on (111) and (001) silicon substrates using sputter-deposited hafnium nitride buffer layers. Wurtzite GaN epitaxial layers are obtained on both the (111) and (001) HfN/Si surfaces, with crack-free thickness up to 1.2 (mu)m. Initial results for GaN grown on the (111) surface show a photoluminescence peak width of 17 meV at 11 K, and an asymmetric x-ray rocking curve width of 20 arcmin. Wurtzite GaN on HfN/Si(001) shows reduced structural quality and peculiar low-temperature luminescence features. However, growth on the (001) surface results in nearly stress-free films, suggesting that much thicker crack-free layers could be obtained.

Recent recoil polarization measurements in Hall A at Jefferson Lab show that the ratio of the electric to magnetic form factors for the proton decreases significantly with increasing Q{sup 2}. This contradicts previous Rosenbluth measurements which indicate approximate scaling of the form factors ({micro}{sub p} G{sub E}{sup p}(Q{sup 2})/G{sub M}{sup p} (Q{sup 2}) {approx} 1). The cross section measurements were reanalyzed to try and understand the source of this discrepancy. They find that the Rosenbluth measurements are consistent when normalization uncertainties are taken into account, and that the discrepancy cannot come from errors in one or two data sets. If there is a problem in the Rosenbluth data, it must be a systematic, {epsilon}-dependent uncertainty affecting several experiments.

Inclusive electron scattering from nuclei at low momentum transfer (corresponding to x {ge} 1) and moderate Q{sup 2} is dominated by quasifree scattering from nucleons. In the impulse approximation, the cross section can be directly connected to the nucleon momentum distribution via the scaling function F(y). The breakdown of the y-scaling assumptions in certain kinematic regions have prevented extraction of nucleon momentum distributions from such a scaling analysis. With a slight modification to the y-scaling assumptions, it is found that scaling functions can be extracted which are consistent with the expectations for the nucleon momentum distributions.

Linear coupling is one of the factors that determine beam lifetime in RHIC. The traditional method of measuring the minimum tune separation requires a tune scan and can't be done parasitically or during the acceleration ramp. A new technique of using ac dipoles to measure linear coupling resonance has been developed at RHIC. This method measures the degree of coupling by comparing the amplitude of the horizontal coherent excitation with the amplitude of the vertical coherent excitation if the beam is excited by the vertical AC dipole and vice versa. One advantage of this method is that it can be done without changing tunes from the normal machine working points. In principle, this method can also localize the coupling source by mapping out the coupling driving terms throughout the ring. This is very useful for local decoupling the interaction regions in RHIC. A beam experiment of measuring linear coupling has been performed in RHIC during its 2003 run, and the analysis of the experimental data is discussed in this paper.

We have developed cermet membranes that nongalvanically separate hydrogen from gas mixtures. The highest measured hydrogen flux was 20.0 cm{sup 3} (STP)/min-cm{sup 2} for an ANL-3a membrane at 900 C. For ANL-3 membranes with thickness of 40-500 {micro}m, hydrogen permeation is limited by the bulk diffusion of hydrogen through the metal phase. The effect of hydrogen partial pressure on permeation rate confirmed this conclusion, suggesting that higher permeation rates may be obtained by decreasing the membrane thickness. Permeation rate in a syngas atmosphere for times up to 190 h showed no degradation in performance, which indicates that ANL-3 membranes may be suitable for long-term, practical hydrogen separation.

Accurate predictions of a polymer component's functional lifetime at best arc tenuous when one has only relatively short term chemical or mechanical property data to extrapolate. We have analyzed a series of silica-filled siloxanes to determine the chemical and microstructural signatures of aging, and we are incorporating these data into rational methodologies for assessing a component's lifetime measured against as-designed engineering properties. We are monitoring changes in mechanical properties, crystallization kinetics, cross-link density changes, and motional dynamics with a variety of analysis methods: Modulated DSC, Dynamic Mechanical Analysis, and Solid-state Nuclear Magnetic Resonance. Previous work has shown that the addition of phenyl side groups to polydimethylsiloxane (PDMS) polymer chains reduces the rate and extent of crystallization of the co-polymer compared to that of pure PDMS. Crystallization has been observed in copolymer systems up to 6.5 mol % phenyl composition by DSC and up to 8 mol % phenyl by XRD. The PDMS-PDPS-silica composite materials studied here are silica reinforced random block copolymers consisting of dimethyl and diphenyl monomer units with 11.2 mol. % polydiphenylsiloxane. Based on this previous work, it is not expected that this material would exhibit crystallization in the polymer network; however, these silicones do, in fact, exhibit …

A systematic methodology is presented and applied for the identification of requirements and issues pertaining to the planning for, and transition to, long term stewardship (LTS). The method has been applied to three of the twelve identified LTS functions. The results of the application of the methodology to contaminated and uncontaminated federal real property in those three functions are presented. The issues that could be seen as impediments to the implementation of LTS are also identified for the three areas under consideration. The identified requirements are significant and in some cases complex to implement. It is clear that early and careful planning is required in all circumstances.

This conference paper describes the high moisture barrier high resistivity coatings on polyethylene terepthalate (PET) have been fabricated and characterized for use in PV module back sheet applications. These thin film barriers exhibit water vapor transmission rates (WVTR) as low as 0.1 g/m2-day at 37.8 C and have shown excellent adhesion (> 10 N/mm) to both ethylene vinyl acetate (EVA) and PET even after filtered xenon arc lamp UV exposure. The WVTR and adhesion values for this construction are compared to and shown to be superior to candidate polymeric backsheet materials.

None

We present the concepts for a storage ring dedicated to and optimized for the production of stable coherent synchrotron radiation (CSR) over the far-infrared wavelength range from about 200 microns to 1 mm.