The response matrix, consisting of the closed orbit change at each beam position monitor (BPM) due to corrector magnet excitations, was measured and analyzed in order to calibrate a linear optics model of SPEAR. The model calibration was accomplished by varying model parameters to minimize the chi-square difference between the measured and the model response matrices. The singular value decomposition (SVD) matrix inversion method was used to solve the simultaneous equations. The calibrated model was then used to calculate corrections to the operational lattice. The results of the calibration and correction procedures are presented.

Using multi-ion MGPT interatomic potentials derived from first- principles generalized pseudopotential theory, we have performed accurate atomistic simulations on the energetic of dislocation motion in the bcc transition metal Mo. Our calculated results include the (110) and (211) generalized stacking fault ({gamma}) energy surfaces, the Peierls stress required to move an ideal straight <111> screw dislocation, and the kink-pair formation energy for nonstraight screw dislocations. Many-body angular forces, which are accounted for in the present theory through explicit three- and four-ion potentials, are quantitatively important to such properties for the bcc transition metals. This is demonstrated explicitly through the calculated {gamma} surfaces, which are found to be 10-50% higher in energy than those obtained with pure radial-force models. The Peierls stress for an applied <111>/{l_brace}112{r_brace} shear is computed to be about 0.025{mu}, where {mu} is the bulk shear modulus. For zero applied stress, stable kink pairs are predicted to form for kink lengths greater than 4b, where b is the magnitude of the Burgers vector. For long kinks greater than 15b, the calculated asymptotic value of the kink-pair formation energy is 2.0 eV.

In order to increase the efficiency of land-based gas turbines, inlet gas temperatures have to be increased, and the amount of air which cools the turbine vanes has to be reduced, to the maximum extent possible. Presently, thermal barrier coatings (TBC`s) are the state of the art in achieving these goals. However, since TBC`s are very thin (typically 100 {mu}m), they have clearly limitations. Since all-ceramic turbine vanes would be a very large and risky development step, Westinghouse is considering to protect the leading edges of turbine vanes with high-performance ceramics. This might be done by either replacing the leading edge with a suitably shaped ceramic part, or by modifying the vanes such that they can accommodate ceramic inserts. Among the most important criteria for the success of ceramics in such applications are (a) thermodynamic compatibility with the turbine vane alloy, (b) sufficient thermal shock resistance to survive the thermal cycling during operation and in particular during emergency shut-down, and a design considering the thermal expansion mismatch of the metallic and ceramic components. This paper presents results of work performed on SiC, SiN, and aluminas.

None

This report consists of four appendices for the final report. They are: Appendix A: 700 C Vapor-Fed AMTEC Cell Calculations; Appendix B: 700 C Vapor-Fed AMTEC Cell Parts Drawings; Appendix C: 800 C Vapor-Fed AMTEC Cell Calculations; and Appendix D: 800 C Wick-Pumped AMTEC Cell System Design.

The Alkali Metal Thermal to Electric Converter (AMTEC) is a high temperature, high efficiency system for converting thermal to electrical energy, with no moving parts. It is based on the unique properties of {beta}{double_prime}-alumina solid electrolyte (BASE), which is an excellent conductor of sodium ions, but an extremely poor conductor of electrons. When the inside of the BASE is maintained at a higher temperature and pressure, a concentration gradient is created across the BASE. Electrons and sodium atoms cannot pass through the BASE. However, the sodium atoms are ionized, and the sodium ions move through the BASE to the lower potential (temperature) region. The electrons travel externally to the AMTEC cell, providing power. There are a number of potential advantages to a wick-pumped, vapor-fed AMTEC system when compared with other designs. A wick-pumped system uses capillary forces to passively return liquid to the evaporator, and to distribute the liquid in the evaporator. Since the fluid return is self-regulating, multiple BASE tubes can use a single remote condenser, potentially improving efficiency in advanced AMTEC designs. Since the system is vapor-fed, sodium vapor is supplied at a uniform temperature and flux to the BASE tube, even with non-uniform heat fluxes and temperatures …

Six immobilization technology projects variants, previously selected for evaluation during the PEIS/ROD process, have been evaluated with respect to the nine basic criteria for fissile materials disposition. Metrics for the criteria were developed to facilitate a comparative analysis of the technology variants. The six technology variants are grouped according to their radiation barrier approach. Information and data for the technology options were provided by limited experimental studies, definitions of process flowsheets, and preliminary evaluations of facility concepts and costs.

Nuclear waste has been sluiced and pumped from storage tank 241-AX-104, leaving a contaminated heel volume. These operations did not include measurements of the removed waste volume leaving an unknown heel volume in the tank. A magnetometer transducer will be lowered through tank riser ports to rest on the heel`s surface. The heel thickness will control the distance between the transducer and the tank`s bottom The instrument`s output varies with the distance from a magnetic mass, such as the tank`s steel bottom, thereby enabling a measurement of the heel depth. Measurements at several tank locations will permit an estimate of the tank`s heel volume. The magnetometer`s output is influenced by adjacent magnetic materials, such as the tank walls, air lift circulators or other equipment installed in the tank. An adjacent vertical steel surface produces a voltage offset in the instrument`s output. Measurements near a tank wall or other tank components may be corrected by noting the offset before the instrument`s output is influenced by the tank bottom. An unlevel or uneven heel surface could orient the magnetometer transducer so that it is not vertically level. The magnetometer readings are influenced by these skewed transducer orientations. The magnitude of these errors …

Quantum groups in general and the quantum Anti-de Sitter group U{sub q}(so(2,3)) in particular are studied from the point of view of quantum field theory. The author shows that if q is a suitable root of unity, there exist finite-dimensional, unitary representations corresponding to essentially all the classical one-particle representations with (half) integer spin, with the same structure at low energies as in the classical case. In the massless case for spin {ge} 1, {open_quotes}naive{close_quotes} representations are unitarizable only after factoring out a subspace of {open_quotes}pure gauges{close_quotes}, as classically. Unitary many-particle representations are defined, with the correct classical limit. Furthermore, the author identifies a remarkable element Q in the center of U{sub q}(g), which plays the role of a BRST operator in the case of U{sub q}(so(2,3)) at roots of unity, for any spin {ge} 1. The associated ghosts are an intrinsic part of the indecomposable representations. The author shows how to define an involution on algebras of creation and anihilation operators at roots of unity, in an example corresponding to non-identical particles. It is shown how nonabelian gauge fields appear naturally in this framework, without having to define connections on fiber bundles. Integration on Quantum Euclidean space and sphere …

None

This document provides a strategy for resolution of the Flammable Gas Safety Issue. It defines the key elements required for the following: Closing the Flammable Gas Unreviewed Safety Question (USQ); Providing the administrative basis for resolving the safety issue; Defining the data needed to support these activities; and Providing the technical and administrative path for removing tanks from the Watch List.

One of the major functions of the Tank Waste Remediation System (TWRS) is to characterize wastes in support of waste management and disposal activities at the Hanford Site. Analytical data from sampling and analysis, along with other available information about a tank, are compiled and maintained in a tank characterization report (TCR). This report and its appendices serve as the TCR for single-shell tank 241-C-109. The objectives of this report are: (1) to use characterization data in response to technical issues associated with tank 241 C-109 waste; and (2) to provide a standard characterization of this waste in terms of a best-basis inventory estimate. The response to technical issues is summarized in Section 2.0, and the best-basis inventory estimate is presented in Section 3.0. Recommendations regarding safety status and additional sampling needs are provided in Section 4.0. Supporting data and information are contained in the appendices.

A weekly publication, the Texas Register serves as the journal of state agency rulemaking for Texas. Information published in the Texas Register includes proposed, adopted, withdrawn and emergency rule actions, notices of state agency review of agency rules, governor's appointments, attorney general opinions, and miscellaneous documents such as requests for proposals. After adoption, these rulemaking actions are codified into the Texas Administrative Code.

This report considers whether the provisions of the FDA's final rule restricting the advertising of cigarettes and smokeless tobacco products violates the First Amendment's guarantee of freedom of speech.

None

The U.S. Department of Energy (DOE) is responsible for the cleanup of inactive DOE sites and for bringing DOE sites and facilities into compliance with federal, state and local laws and regulations. The DOE's Office of Environmental Management (EM) needs advanced technologies that can make environmental restoration and waste management operations more efficient and less costly. These techniques are required to better characterize the physical, hydrogeological, and chemical properties of the subsurface while minimizing and optimizing the use of boreholes and monitoring wells. Today the cone penetrometer technique (CPT) is demonstrating the value of a minimally invasive deployment system fix site characterization. Applied Research Associates is developing two new sensor packages for site characterization and monitoring. The two new methods are: . Electrical Resistivity Tomography (ERT) and . Ground Penetrating Radar (GPR) Tomography. These sensor systems are now integrated with the Cone Penetrometer Technique (CPT). The results of this program now make it possible to install ERT and GPR units by CPT methods and thereby reduce installation costs and total costs for ERT and GPR surveys. These two techniques can complement each other in regions of low resistivity where ERT is more effective and regions of high resistivity where GPR …

This document provides an overview of the basic planning and work of the Department of Energy Richland Operations Office (DOE-RL). It defines key terms, concepts, and processes used in Hanford`s Environmental Management (EM) activities. It is not intended to provide complete details on the topics discussed. It does, however, provide a roadmap of the overall process so that opportunities for tribal, regulator, and public involvement can be clearly identified. Many documents are referenced in this plan. Each is described in some detail in Section 5, and cross-references to that section are provided throughout the discussion in Sections 1 through 4.

The purpose of this document is to provide a single referenceable document that provides the X/Qs for the solid waste facilities in the 200 Area, that is to provide the X/Qs for the Solid Waste Dispersal Facilities Master Safety Analysis Report (WHC-SD-WM-MSAR-001, REV. 0, 1996). The X/Qs will be used for the radiological dose estimates in the accident safety analyses. Thus, this document is also to provide the information necessary to perform bounding estimates of the radiological consequences for hypothetical accidents for various solid waste facilities. This document is to examine the variations in the plume dispersion factors associated with the various solid waste facilities. Specifically examined are X/Qs associated with different receptors located in different sectors and at different distances. Examination of one facility included a large area X/Q, while examination of another facility included an elevated release. Generally, the X/Qs are determined for ground releases with and without building wake. In addition, sensitivity of how plume characteristics were affected by using different meteorological data was examined. Each receptor described in this document was evaluated for both 99.5% and 50% meteorological data. Attributes such as plume meander, plume rise, settling and wash-out are not considered in this document.

An important consideration in assessing environmental impacts for the National Environmental Policy Act (NEPA) is to establish a baseline from which to evaluate potential changes associated with a proposed action. For some assessments, establishment of the baseline is straightforward because the proposed action is located in an undeveloped area which has been negligibly affected by human activity. For other assessments, however, the baseline may be more difficult to determine because the proposed action may occur in an area where human activities have affected the environment and, in essence, have established a new (and often changing) baseline. Frequently, appreciable degradation has occurred on the proposed site itself. For such cases, the question arises as to whether the unperturbed condition or the present condition is more appropriate to use as the baseline. This paper argues that a proposed action in a previously disturbed area should not be assessed merely in relation to the new baseline. Rather, a more comprehensive evaluation should be given that compares potential environmental effects with both the unperturbed condition and the present condition and consequently presents a more balanced approach to the assessment. Furthermore, the sponsoring federal agency should take the opportunity offered by the proposed action to …

Optimization of molecular detection efficiencies is important for analytical applications of single molecule detection methods. In microdroplets some experimental limitations can be reduced, primarily because the molecule cannot diffuse away from the excitation and collection volume. Digital molecular detection using a stream of microdroplets has been proposed as a method of reducing concentration detection limits by several orders of magnitude relative to conventional measurements. However, the bending and reflection of light at the microdroplet`s liquid-air interface cause the illumination intensity and fluorescence intensity collected to be strongly dependent on the position of the molecule within the droplet. The goal is to model the detection of single molecules in microdroplets so that one can better understand and optimize detection efficiencies. In the first year of this modeling effort the authors studied the collection of fluorescence from unit-amplitude dipoles inside of spheres. In this second year they modified their analysis to accurately model the effects of excitation inhomogeneities, including effects of molecular saturation, motion of the droplet, and phase variations between the two counter-propagating waves that illuminate the droplet. They showed that counter-propagating plane wave illumination can decrease the variations in the intensity which excites the molecules. Also in this second year …

With the end of the Cold War, the Strategic Arms Reduction Treaties (START), and other agreements, the United States and Russia have dramatically reduced their arsenals of nuclear weapons. As a result, each side has accumulated large stockpiles of plutonium, one of the principal materials used in nuclear warheads. The United States recently declared a holding of approximately 50 metric tons of weapons-usable plutonium excess to military needs. Even greater levels are believed to exist in Russia.

PHENIX is one of the two large experiments at the Relativistic Heavy Ion Collider (RHIC) currently under construction at Brookhaven National Laboratory. The detector consists of 11 sub-detectors, that are further subdivided into 29 units (``granules``) that can be operated independently, which includes simultaneous data taking with independent data streams and independent triggers. The detector has 250,000 channels and is read out by front end modules, where the data is buffered in a pipeline while awaiting the level trigger decision. Zero suppression and calibration is done after the level accept in custom built data collection modules (DCMs) with DSPs before the data is sent to an event builder (design throughput of 2 Gb/sec) and higher level triggers. The On-line Computing Systems Group (ONCS) has two responsibilities. Firstly it is responsible for receiving the data from the event builder, routing it through a network of workstations to consumer processes and archiving it at a data rate of 20 MB/sec. Secondly it is also responsible for the overall configuration, control and operation of the detector and data acquisition chain, which comprises the software integration for several thousand custom built hardware modules. The software must furthermore support the independent operation of the above …

This Quality Assurance Program Plan (QAPP) provides information on how the Quality Assurance Program is implemented for the 324 Building B-Cell Safety Cleanout Project (BCCP). This QAPP is responsive to the Westinghouse Hanford Company Quality Assurance Program and Implementation Plan, WHC-SP-1131, for 10 CFR 830.120, Nuclear Safety Management, Quality Assurance Requirements; and DOE Order 5700.6C, Quality Assurance. This QAPP supersedes PNNL PNL-MA-70 QAP Quality Assurance Plan No. WTC-050 Rev. 2, issue date May 3, 1996. This QAPP has been developed specifically for the BCCP. It applies to those items and tasks which affect the completion of activities identified in the work breakdown structure of the Project Management Plan (PMP). These activities include all aspects of decontaminating B-Cell and project related operations within the 324 Building as it relates to the specific activities of this project. General facility activities (i.e. 324 Building Operations) are covered in the Building 324 QAPP. In addition, this QAPP supports the related quality assurance activities addressed in CM-2-14, Hazardous Material Packaging and Shipping, and HSRCM-1, Hanford Site Radiological Control Manual, The 324 Building is currently transitioning from being a Pacific Northwest National Laboratory (PNNL) managed facility to a B and W Hanford Company (BWHC) managed facility. …

This Quality Assurance Program Plan (QAPP) provides an overview of the quality assurance program for Building 324. This plan supersedes the PNNL Nuclear Facilities Quality Management System Description, PNL-NF-QMSD, Revision 2, dated March 1996. The program applies to the facility safety structures, systems, and components and to activities that could affect safety structures, systems, and components. Adherence to the quality assurance program ensures the following: US Department of Energy missions and objectives are effectively accomplished; Products and services are safe, reliable, and meet or exceed the requirements and expectations of the user; Hazards to the public, to Hanford Site and facility workers, and to the environment are minimized. The format of this Quality Assurance Program Plan is structured to parallel that of 10 CFR 83 0.120, Quality Assurance Requirements.