An improved microresistance testing method to measure the thickness of copper plating in plated-through holes of double-sided printed wiring boards is presented. A new probe design, combined with a microprocessor controller, makes it possible for a direct reading tester to provide variables data. Tester design and software programs for the system are included. Results of correlation studies, comparing the improved resistance method to cross-sectional measurements are presented. Limitations on the microresistance test method are discussed.

Vibrating wire stressmeters were installed in the Spent Fuel Facility at the Nevada Test Site. These stressmeters will measure the changes in in situ stress during the five-year spent fuel test. Before installation, laboratory tests were conducted to study reproducibility of placement and to develop a program hopefully to reduce corrosion of the stressmeters while in place at the Spent Fuel Facility. These laboratory tests are discussed along with the installation of the stressmeters at the Spent Fuel Facility.

"This report presents engineering details, statistics, individual borehole histories, and geophysical logs of the four holes drilled in the Lemhi Pass, Montana/Idaho area." (from Introduction)

The shower counter system of the SLAC-LBL Mark II detector is a large lead/liquid argon system of the type pioneered by Willis and Radekal; however, it differs in most details and is much larger than other such detectors currently in operation, It contains, for example, 8000 liters of liquid argon and 3000 channels of low noise electronics, which is about eight times the size of the system of Willis et al. in the CERN ISR. This paper reports, with little reference to design, on the operation and performance of the Mark II system during approximately a year and a half of operation at the Stanford Linear Accelerator Center's e{sup +}-e{sup -} facility, SPEAR. The design and construction of the system have previously been described and a detailed discussion of all aspects -- design, construction, operation, and performance -- is in preparation.

We present a study of the decay properties of charmed D mesons produced near the peak of the {psi}" (3770) resonance in e{sup +}e{sup -} annihilation. Branching fractions for nine Cabibbo-favored and three Cabibbo-suppressed decay modes are presented along with upper limits on one additional Cabibbo-favored and four additional Cabibbo-suppressed decay modes. A study of K{pi}{pi} decay mode Dalitz plots reveals a large quasi-two-body pseudoscalar-vector component for the D{sup 0} decays and an apparent nonuniform population an the Dalitz plot for the D{sup +} decay into K{sup -}{pi}{sup +}{pi}{sup +}. Using tagged events, we measure the charged particle multiplicity and strange particle content of D decays. A measurement of the D{sup +} and D{sup 0} semileptonic decay fractions indicates that the D{sup +} has a significantly longer lifetime than the D{sup 0}.

The oxidation behavior of type 316 stainless steel and candidate advanced alloys for the gas-cooled fast reactor (GCFR) is being investigated at General Atomic Company. The test program consists of oxidation tests in prototypic GCFR environments. Two tests have been completed to date and a third test is under way. The first test was performed in an environment containing a hydrogen/water ratio of 10. The oxidation behavior of all the alloys was good to excellent in this environment. Preferential oxidation of chromium was responsible for this behavior. The second test was performed in an environment containing a hydrogen/water ratio of 0.25, where both chromium and iron oxides are thermodynamically stable. Some of the alloys and some of the ribbed type 316 stainless steel test specimens showed unacceptable oxidation resistance in this environment. In the third test, presently under way, two different pretreatment procedures are being used to control the poor oxidation behavior observed in the second test. Early results show some degree of success.

This report outlines the capabilities and limitations of the two centrifuges and gives other details which must be considered in preparing test specifications and designing fixtures, gives the theory and terminology of centrifuge testing, and describes the layout, operating principles, support functions, and reference material for each facility.

Newsletter issued by the Advisory Council for Technical-Vocational Education in Texas discussing news, events, and other relevant information related to technical and vocational education for adults in Texas.

Average record data listings taken during aerial gamma-ray and magnetic surveys of the Nulato quadrangle in Alaska.

The impact of fossil fuel use in the US on worldwide CO/sub 2/ emissions and the impact of increased coal utilization on CO/sub 2/ emission rates are assessed. The aspects of CO/sub 2/ control are discussed as well as the available CO/sub 2/ removal sites. The primary factor affecting the practicability of a CO/sub 2/ control system is its energy requirements. Of the three potential CO/sub 2/ control points, removal from the stacks of fossil fuel power plants appears to require the least amount of energy. Estimates of the energy required to capture and recover CO/sub 2/ from coal-fired power plant stacks by various processes are presented. Although capture and recovery of CO/sub 2/ is an important consideration in the overall scheme of CO/sub 2/ control, disposal or reuse of recovered CO/sub 2/ may be the weakest link in the CO/sub 2/ control chain. Of the several options considered, deep ocean storage appears to be the most promising. Two control scenarios are evaluated, one based on the absorption of CO/sub 2/ contained in power plant flue gas by seawater; the other, based on absorption of CO/sub 2/ by monoethanolamine (MEA). Captured CO/sub 2/ is injected into the deep ocean in …

Curtailment planning at a generally rudimentary level has been undertaken by the governments of some twenty states. Many utilities have demand-curtailment plans, however, these are often incorporated in plans for meeting capacity shortages. In at least five states, there are apparently no curtailment plans either at the state-government level or at the utility level. Moreover, none of the existing electricity demand curtailment plans examined included an explicit statement of the planners' objective in arriving at a specified sharing of the burdens of curtailment among consumer classes. Yet clearly the actual allocations of such burdens will affect the cost of the shortage. Since a study of state planning failed to yield a clear-cut indication of which of many possible curtailment allocation schemes would best serve as a point of departure for the design of an optimal curtailment strategy to deal with prolonged supply deficiencies, it was then decided to use a linear-programming approach. The advantages of such an approach are examined first, after which some important conceptual and practical problems in the design of a specific linear-programming model are addressed. A mathematical statement of the model is then followed by a brief review the principal methodological shortcomings of the linear-programming approach. …

A Workshop on Program Options in Intermediate-Energy Physics sponsored by the US Department of Energy was held at Los Alamos Scientific Laboratory, August 20 to 31, 1979. The scope of the workshop included all laboratories in intermediate-energy physics, worldwide, and all of these sent representatives to the workshop. The workshop addressed itself to the critical questions on nuclear and particle physics and how they can best be investigated by intermediate-energy accelerators. Among the questions that the workshop members considered were: (1) what are the important physics topics which might be understood through research on these accelerators in the next 10 years. These topics include, but are not restricted to, fundamental interactions and symmetries in particle physics, and nuclear modes of motion, structure, and reaction mechanisms; (2) what experiments should be undertaken to carry out the program. What are the kinematical conditions, accuracies, resolutions, and other parameters required to obtain the desired knowledge; (3) which accelerators are best suited for each experiment. What work at other laboratories (low-, intermediate-, or high-energy) could be undertaken to complement and/or supplement the proposed LAMPF program; and (4) what new facility capabilities should be explored for the long-term future. The workshop was divided into small …

The University of Tennessee Space Institute (UTSI) reports on significant activity, task status, planned research, testing, development, and conclusions for the Magnetohydrodynamics (MHD) Coal-Fired Flow Facility (CFFF) and the Research and Development Laboratory. Although slowed by incessant rain during several days, work on the CFFF Bid Packages progressed to nearly 100 percent completion, excluding later punchlist items. On the quench system, the cyclone separator was delivered to UTSI, and under Downstream Components, the secondary combustor was received and the radiant slagging furnace was emplaced at the CFFF. Water quality analysis of Woods Reservoir provided the expected favorable results, quite similar to last year's. Generator experiments describing local current distribution are reported along with behavior under conditions of imposed leakage. Also, during the Quarter, the shelter for the cold flow modeling facility was constructed and circuits installation begun. A jet turbine combustor was tested for use as a vitiation burner. Samples taken from the exhaust duct, besides other applications, show that the refractories used are performing well in alleviating heat loss while exhibiting acceptable degredation. A new resistive power take-off network was designed and implemented.

New hydride derivatives of thorium (IV) and uranium (IV), HM[N(SiMe{sub 3}){sub 2}]{sub 3}, have recently been prepared. This paper describes the crystal structure of the uranium species, though the hydride-ion was not located, and shows that the thorium analogue is isostructural. The reaction chemistry and spectroscopy leave no doubt that these derivatives are authentic examples of four-coordinate, monomeric hydride, compounds.

Experimental and theoretical studies of field reversal in a mirror machine are reported. Plasma-gun experiments demonstrate that reversed-field plasma layers are formed. Low energy plasma flowing behind the initially produced plasma front prevents tearing of the layer from the gun muzzle. MHD simulation shows that tearing can be obtained by impeding the slow plasma flow with a plasma divider. It is demonstrated theoretically that a field-reversed mirror imbedded in a multipole field can be sustained in steady state with neutral-beam injection even in the absence of impurities. MHD stability analysis shows that growth rates of elongated reversed-field theta-pinch configurations decrease with axial extension, which indicates the importance of including finite Larmor radius in the analysis. Tilting-mode criteria are dramatically improved by proper shaping, and a problimak shape is proposed. Tearing mode stability of reversed-field theta-pinches is greatly enhanced by flux exclusion. Self-consistent, 1-1/2-dimensional transport codes have been developed, and initial results are presented.

A preliminary study of industrial energy conservation measures initiated by states under the State Energy Conservation Program is presented. Elements, targets, and administration of state programs are briefly examined. As the results of the study indicate, the states perceive the need for Federal assistance in programs to: establish a forum for coordination of state programs and interchange of approaches and program materials; provide to state offices direct technical assistance, including specific program information, training materials and manuals directed toward specific industries, and an energy accounting methodology; promote national industrial energy conservation measures; develop methods for providing financial assistance to companies, especially small business, for incorporating energy conserving measures; devise a plan for coordinating the state energy-related regulatory activities; and disseminate information on Federal programs and regulations that may impact energy-related decisions at the state level and within private industry.

The structural arrangement of a hydrated glass surface depends on the composition, thermal history and surface treatment. This paper considers the surface treatment of a lead glass with weak and strong acid solutions and in particular hydrogen peroxide, to give a microscopically clean microsphere.

The agencies involved in geothermal development are listed and individually described. A summary of existing geothermal resource laws and their statute numbers are given followed by a discussion on the problems associated with them. The local agencies and their regulations of geothermal development are discussed. The local, state, and federal agencies directly involved in geothermal development and their permitting requirements are tabulated. Some step-by-step instructions for determining what permits are necessary for developing a specific geothermal resource are given. A list of selected references and a list of additional resources for geothermal information and referral are included. (MHR)

From summary: The purpose of the study is to develop information that will contribute to the definition of the potential role of photovoltaics in meeting future energy demands in agriculture.

From introduction: The objectives of the technical effort are to identify and characterize agricultural energy demands that can effectively use P/V power systems and to determine performance and cost-estimates for the designs.

Forward: The Final Report summarizes the findings and project work in conjunction with the "Photovoltaic" Applications Definition and Photovoltaic System Definition Study in the Agricultural Sector" under Contract Number 07-6951.

In order to assist in the study of instrumentation and analytical needs for reprocessing plants, a workshop addressing these needs was held at Oak Ridge National Laboratory from May 5 to 7, 1980. The purpose of the workshop was to incorporate the knowledge of chemistry and of advanced measurement techniques held by the nuclear and radiochemical community into ideas for improved and new plant designs for both process control and inventory and safeguards measurements. The workshop was athended by experts in nuclear and radiochemistry, in fuel recycle plant design, and in instrumentation and analysis. ORNL was a particularly appropriate place to hold the workshop since the Consolidated Fuel Reprocessing Program (CFRP) is centered there. Requirements for safeguarding the special nuclear materials involved in reprocessing, and for their timely measurement within the process, within the reprocessing facility, and at the facility boundaries are being studied. Because these requirements are becoming more numerous and stringent, attention is also being paid to the analytical requirements for these special nuclear materials and to methods for measuring the physical parameters of the systems containing them. In order to provide a focus for the consideration of the workshop participants, the Hot Experimental Facility (HEF) being designed …

This report summarizes the work completed during the first year of a two-year grant by NCI/HEW to investigate the feasibility of developing a D-T neutron generator for use in cancer therapy. Experiments have continued on the Target Test Facility (TTF) developed during a previous grant to investigate high-temperature metal hydrides for use as target materials. The high voltage reliability of the TTF has been improved so that 200 kV, 200 mA operation is now routine. In recent target tests, the D-D neutron production rate was measured to be > 1 x 10/sup 11//s, a rate that corresponds to a D-T neutron production rate of > 1 x 10/sup 13//s - the desired rate for use in cancer therapy. Deuterium concentration depth profiles in the target, measured during intense ion beam bombardment, show that deuterium is depleted near the surface of the target due to impurities implanted by the ion beam. Recent modifications of the duopigatron ion source to reduce secondary electron damage to the electrodes also improved the ion source efficiency by about 40%. An ultra high vacuum version of the TTF is now being constructed to determine if improved vacuum conditions will reduce ion source impurities to a sufficiently …

Parameters controlling the formation of protective and non-protective oxides on 304 stainless steel were examined by using Auger electron spectroscopy to monitor oxides formed in the vacuum chamber. Variables found to influence the oxide formation include: oxygen partial pressure, the location of the oxide over a grain or grain boundary, sample grain size, and anneal treatments.