From Abstract: "This report is one of a sequence of quarterly reports, each designed to up-date its predecessor beginning with HASL-42, "Environmental Contamination from Weapon Tests". Herein are presented data which have accrued since HASL-55. Levels of strontinum-90 in fallout, milk, air, water, vegetation, foods, and bone are given, based on data available from February 1, 1959 to May 20, 1959."

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Will Wilson, regarding a legal question submitted for clarification: Whether dependent and neglected child cases are to be filed in the District Court or the Juvenile Court of Galveston County.

The demand plot has a 5-set, modified pump decay curve; it shows that 20,000 gpm emergency flow would be required within 80 seconds of complete pump power failure. Bases for the demand curve are constant bulk inlet temperature of 2 C, constant bulk outlet temperature of 95 C, K-3 I&E fuel elements, and initial reactor flow of 188,000 gpm.

None

The defueling of the S2G Reactor which was conducted at the Electric Boat Division, General Dynamics Corporation Groton Connecticut during January 1959, is reported from the viewpoint of the participating personnel from Knolls Atomic Power Laboratory. The sequence of events is outlined, difficulties encountered during the operation are described, and conclusions of possible interest to other naval nuclear reactors are given (auth)

Considerable production gains might be attained if each reactor discharged its entire flattened region during one scheduled outage instead of utilizing several outages for this purpose. Several of the older reactors are now discharging a high percentage of their flattened zones in a single outage and could be put into this type of operation with relatively little difficulty. Production gains may be possible through better flattening efficiency, a more favorable rupture rate effect, fewer non-equilibrium losses, higher conversion ratio, and more efficient usage of outage work. Since this document is written Primarily from the Operational Physics standpoint, some gains and pitfalls which must be evaluated by other affected groups will only be mentioned here as possibilities. The purpose of this document is simply to point out the potential gains in flattening efficiency from this method. Potential gains from improved fuel performance have been described in another document.

Available knowledge of precision limits in S.S. accountability measurements and/or calculations by reactor and chemical processing groups is surveyed and summarized. Experienee in comparisons of reactor (production and research) calculations vs. chemical plant accountability measurements is also reported. A general tentative conclusion is that available precisions ( plus or minus 0.54 to plus or minus 0.78%) in chemical plant measurements (bulk and analytical) for fissionable material accountability is superior to the variable precision ( plus or minus 1.0 to 1l.0%) possible by calculations (nuclear and/or engineering) of power reactor systems; however, with operation and empirical experience (e.g., after two or three core loadings), it is believed that calculations for given reactors can attain acceptable precisions, e,g., less than plus or minus 1.0%. It may be proposed that fuel payments be made as follows: 90% of fuel value based on reactor calculations, an additional 5% based on dissolver analyses, and final settlement based on chemical plant material balance (product plus loss analyses). (auth)

Available knowledge of precision limits in S.S. accountability measurements and/or calculations by reactor and chemical processing groups is surveyed and summarizes. Experience in comparisons of reactor (production and research) calculations versus chemical plant accountability measurements is also reported. A general tentative conclusion is that available precisions (+/- 0.54 to +/- 0.78% ) in chemical plant measurements is also reported. A general tentative conclusion is that available precisions (+/- 1.0 to +/- 11.0%) possible by calculations (nuclear and/or engineering) of power reactor systems; however, with operation and empirical experience (e.g. less than +/-1.0%

None

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Will Wilson, regarding a legal question submitted for clarification: Whether H.B. 51 and H.B. 612 require certification by the Comptroller of Public Accounts pursuant to Sec. 49a, Article III of the State Constitution.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Will Wilson, regarding a legal question submitted for clarification: Authority of the State Building Commission in regard to payment of professional fees to an attorney for services in connection with land acquisition.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Will Wilson, regarding a legal question submitted for clarification: Whether Article 666 controls the purchase of office equipment by the Texas Department of Agriculture from the Insurance Liquidator.

Introduction: "It is the purpose of this note to describe the construction and operation of the plasma injectors used in the magnetic high compression experiments in progress at the Lawrence Radiation Laboratory at Livermore. As the investigations of these injections is still in progress, remarks concerning their operation or the characteristics of the injected plasma are of a tentative nature."

The construction and operation of the plasma injector, Toy Top, used ia the magnetic high compression experements in progess at the Lawrence Radiation Jab. at Livemore are described The essential part of the injector consists of a stack of deuterated titanium washers 3/4 in. O.D. and/2 in. I.D. Details of the construction are sbown (W.D.M.)

Volatility Pilot Plant Mark III Fluorinator is a doublechamber type vessel, each chamber 2 1/2 ft by 16 in. outside diameter separated by a 5-in. pipe 15 in. long. ASME flanged and dished heads are used for the chamber tops and conical sections with a 60 deg apex angle for the chamber bottoms. A new furnace designed to maintain the complete lower chamber (molten salt+ freeboard) above melt temperature is to eliminate past experiences of salt solidification on the wall, heads, and in or on the internal process lines. External pipe runs are autoresistance heated to allow melting and drain back of salt plugs. The upper chamber serves as a gas de-entrainment and solids precipitation device to retain most of the entrained salt and condensable fluorides in the 100 to 400 deg C range. (auth)

Volstility Pilot Plant Mark III Fluorinator will be a double-chamber type vessel, each chamber 2-1/2ft. by 16in. o.d. separated by a 5 in. pipe 15 in. long. ASME flanged and dished heads will be used for the chamber tops and conical sections with a 60º apex angle for the chamber bottoms. A new furnace designed to maintain the complete lower chamber (molten salt + freeboard) above melt temperature will eliminate past experiences of salt solidification on the wall, heads, and in or on the internal process lines. External pipe runs will be sutoresistance heated to allow melting and drain back of salt plugs. The upper chamber serves as a gas de-entrainment and solids precipitation device to retain most of the entrained salt and condensable fluorides in the 100-400°C temperature range.

Introduction: This document describes the results of a six-week conceptual design study of an organic moderated and cooled reactor (OMCR) power plant adapted to a Class T-7 tanker.

Sections of the dummies furnished by Radiological Engineering, Process Reactor Development Operation were machined into 1/4 inch diameter by 1 inch long cylinders and irradiated in the Quickie Facility at F area. The pieces were discharged directly into a holder one foot from the Beckman chamber. The transient time from in-pile to the chamber is approximately 30 seconds. The readings were taken using a Beckman chamber, Beckman Micro-Micro Ammeter and Recorder. This system has been calibrated with Co{sup 60} sources obtained from the Oak Ridge National Laboratory. We are including data taken from a sample of 61-S and 99.998 per cent aluminum which may be of interest.

From Abstract: "Automatic computation of these general formulas from raw data and procedures for their adaption to a number of specific analyses are described."

Results of four experimentul runs in the Fluorox fluidized bed reactor system are reported. The engineering feasibility of UF/sub 6/ production from UF/ sub 4/ by use of dry air of O/sub 2/, 2UF/sub 4/ + O/sub 2/ = UF/sub 6/+ UO/sub 2/ F/sub 2/, in an Inconel fluidized bed reactor at 800 to 850 deg C was demonstrated in two experimental tests in which greater than 90% of the theoretical amount of UF/sub 6/ was collected or measured. Two runs made with crude UF/sub 4/ (produced from unpurified mill concentrate) as the feed material, showed thnt UF/sub 6/ could be produced at 700 to 725 deg C but corrosion on Inconel was prohibitive. (auth)

Results of four experiemental runs in the Fluorox fluidized bed reactor system are reported. The engineering feasibility of UF6 production from UF4 by use of dry air of O2, 2UF4 + O2 = UF6 + UO2F2, in an Inconel fluidized bed reactor at 800-850°C was demonstrated in two experimental tests in which greater than 90% of the theoretical amount of UF6 was collected or measured. Two runs made with crude UF4 (produced from unpurified mill concentrate) as the feed material, showed that UF6 could be produced at 700-725°C but corrosion on Inconel was prohibitive.

The proposed operating conditions for fuel elements to be charged into the NPR require the fuel to be of an extended surface geometry and maintain adequate strength and corrosion resistance in 300 C water. A contract was let to Nuclear Metals Inc. to produce by co-extrusion lengths of fuel rod containing both natural and 1.6% enriched uranium of irradiation quality for fabrication into fuel elements. The fuel rods used in the irradiation test represent the first enriched uranium rods coextruded in 0.030 inches of Zircaloy-2 to be irradiated and examined at Hanford. The rods used for this test were fabricated into four, 4 rod cluster fuel elements thus allowing adequate space between individual rods for expansion in the case of a fuel rod failure. This rod was of particular interest since it contained an irregular uranium-Zircaloy-2 interface. The purpose of the irradiation was to determine the dimensional stability of coextruded fuel rods and to determine whether the irregularity in the bond interface had any effect upon the irradiation performance of the fuel. Fuel elements were irradiated in 200 C water in the KER Loop 2 facility to an exposure of 0.28 a/o burnup (2,200 MWD/T). Post irradiation examination showed that …

At the present time, plants in the 100 to 500 Mw size range are more numerous and carry the greatest portion (over 50%) of the total steam-electric plant load in the US utillties industry. The contribution of plants of over 1,000-Mw capacity is increasing more rapidly than any other size classification and at present represents about 10% of the total capacity. By 1962 the TVA will have six plants with capacities of over 1,000-Mw. The largest steam-electric plant in the US is the TVA plant at Kingston, Tenn., with a nameplate capacity of 1,440Mw. Turbine-generator wits are also following a trend of ever-increasing size. In present construction, the 150 to 200 Mw size range for units ls the most common and represents the greatest contribution to capacity. Two units of 500-Mw nameplate rating each, the largest in the US, are on order by the TVA, and an 80 Mw unit is contemplated. (auth)

At the present time, plants in the 100-500Mv size range are more numerous and carry the greatest portion (over 50%) of the total steam-electric plant load in the U.S. utilities industry. The contribution of plants of over 1,000-Mv capacity is increasing more rapidly than any other size clarification and at present represents about 10% of the total capacity. By 1962 the TVA will have six plants with capacities of over 1,000-Mv. The largest steam-electric plant in the U.S. is the TVA plant at Kingston, Tenn., with a nameplate capacity of 1,440-Mv. Turbine-generator units are also following a trend of ever-increasing size. In present construction, the 150-200 Mv size range for units is the most common and represents the greatest contribution to capacity. Two units of 500-Mv nameplate rating each, the largest in the U.S., are on order by the TVA, and an 800 Mv unit is contemplated.