Memorandum presenting a study of an acceleration-limiting control on a turbojet engine in order to determine its feasibility as an acceleration control. A proportional-plus-integral type of controller was used in the investigation. Results regarding the one-loop control and two-loop control are provided.

Memorandum presenting an acceleration-limiting control used on a turbojet engine to study the feasibility of its use as an acceleration control. A proportional-plus-integral type of controller was used in this investigation. Results regarding one-loop control and two-loop control are provided.

Report presenting an investigation at Mach numbers of 1.61 and 2.01 to determine the pressure distributions for a series of 20 controls on a 60 degree delta wing. Tests occurred at a range of angles of attack and control deflections. Results regarding basic pressure distributions, comparison of experimental and theoretical results, and experimental comparisons are provided.

Report presenting an investigation at two Mach numbers to determine the pressure distributions for a series of 20 controls on a 60 degree delta wing. Thirteen controls were of the balanced tip type and seven of the controls were of the more conventional trailing-edge type. Results regarding the basic pressure distributions, comparison of experimental and theoretical results, and some experimental comparisons are provided.

Report presenting a single, ordinary, nonlinear differential equation of second order that can be used for determining entry into an exponential planetary atmosphere. The reduced equation includes various terms, some of which represent the gravity force, the centrifugal acceleration, and the lift force. A number of solutions for lifting and nonlifting vehicles entering at various initial angles are obtained from the complete nonlinear equation.

"A wind-tunnel investigation was made to determine the effects on the aerodynamic characteristics of a 35 degree swept-wing airplane of applying area-suction boundary-layer control to the trailing-edge flaps. Flight tests of a similar airplane were then conducted to determine the effect of boundary-layer control in the handling qualities and operation of the airplane, particularly during landing. The wind-tunnel and flight tests indicated that area suction applied to the trailing-edge flaps produced significant increases in flap lift increment" (p. 1).

Memorandum presenting lift and drag characteristics that have been determined in flight in the landing-approach configuration on 41 jet-propelled fighter-type airplane arrangements, including various wing boundary-layer-control installations. Minimum comfortable approach speeds for carrier-type landings were evaluated for these airplanes by four test pilots. Results regarding the presentation of data, methods for the prediction of minimum comfortable approach speed, reasons for limiting approach speed, comparison of flight and predicted approach speeds, and comparison of test pilots' and service pilots' approach speed are provided.

Report presenting lift and drag characteristics in the landing-approach configuration on 41 jet-propelled fighter-type airplane arrangements using flight testing. Minimum comfortable approach speeds were evaluated by four test pilots. Suggestions for achieving optimal speeds for approach under various conditions are also provided.

"The amount of water in cloud droplet form ingested by a full-scale supersonic nose inlet with conical centerbody was measured in the NACA Lewis icing tunnel. Local and total water impingement rates on the cowl and centerbody surfaces were also obtained. All measurements were made with a dye-tracer technique" (p. 1).

Memorandum presenting an experimental investigation to determine the effect on drag of applying the moment-of-area-rule modifications to wing-body combinations with various wing plan forms. The effect of mounting air-to-air type missiles on the wing-mounted bodies of revolution which are part of the moment-of-area-rule modification was also investigated.

Report presenting studies to determine the effect of sliding velocity and ambient temperature on the friction properties and endurance lift of thin lead monoxide coatings bonded to type 440-C martensitic stainless steel. Results regarding the effect of run-in on endurance life are also provided.

Report presenting an investigation of a pylon-mounted-store airplane configuration in the supersonic pressure tunnel at a Mach number of 1.61. Forces and moments of a complete wing-fuselage-store-pylon combination was measured for a variety of pylon-mounted store locations below the wing. Results regarding the effect of store position on the aerodynamic characteristics in pitch, effect of store position on the aerodynamic characteristics in sideslip, store fins and store tail cone, double-store installation, effect of pylon location, and relative contribution of store-pylon forces toward total force are provided.

Transonic flutter derivatives for unswept wing control surface configurations determined by pressure cell measurements. The control surfaces were mounted on a wing with an aspect ratio of 3, a taper ratio of 0.6, and a wing-thickness ratio of 0.06. Results regarding aerodynamic balance, vortex generators, splitter-plate configurations, and wedges are provided.

Report presenting a determination of transonic flutter characteristics from pressure cell measurements on control surfaces sinusoidally oscillated at an amplitude of plus or minus 1.08 degrees at frequencies from 5 to 30 cycles per second. Various control-surface configurations were investigated, including internal and external aerodynamic balance, vortex generators, a splitter-plate type of control surface, and superposition of triangular shaped wedges or tetrahedra along the rear portion of the control-surface chord.

Memorandum presenting an experimental investigation of the pressure-recovery performance of a fixed-geometry, two-cone, two-drag inlet at Mach number 2.95. Low drag was achieved by use of an internally cylindrical cowl with rapid flow turning that was within 4 degrees of the wedge angle for shock detachment. Results regarding the inlet performance and evaluation of inlet performance are provided.

Report presenting an experimental investigation to determine the effects of planing in a wake on the forces of a planing surface and to locate desirable positions in the wake with regard to the lift and lift-drag ratio of the planing surface. Two combinations of hydro-skis were tested: one with two in tandem and one with three arranged with one hydro-ski in the front and two in the back. Results indicated that the rear hydro-ski in tandem arrangement could have large increases in lift coefficient and small improvements in lift-drag ratio compared with the regular configuration.

Report presenting an investigation in an altitude test chamber using a turbojet engine equipped with an afterburner and ejector to compare directly two techniques of determining thrust that are both applicable to flight installations. One method uses a swinging uncooled rake at the ejector outlet while the other requires extensive instrumentation to measure the momentum forces of systems and the force on the internal surface of the ejector nozzle. Results regarding the swinging-rake technique and internal-pressure technique are provided.

"A study has been made of a flare-cylinder configuration to investigate its feasibility as a reentry body of an intermediate range ballistic missile. Factors considered were heating, weight, stability, and impact velocity. A series of trajectories covering the possible range of weight-drag ratios were computed for simple truncated nose shapes of varying pointedness, and hence varying weight-drag ratios" (p. 1).

Note presenting flight tests conducted with a medium-size single-rotor helicopter, one blade of which was equipped with strain gages, to determine the effects of retreating-blade stall on the rotor blade bending and torsional moments during high-speed flight and pull-up maneuvers. The results indicate that retreating-blade stall has a substantial effect on the periodic rotor blade moments. Results regarding the effect of stall in steady forward flight and effect of stall in pull-up maneuvers are provided.

Report presenting aerodynamic forces for an external-store installation on the Douglas D-558-II research airplane. Store-pylon, pylon-alone, and fin loads were determined during angle-of-attack and angle-of-sideslip maneuvers over a range of Mach numbers. Results regarding the side-force coefficients, normal-force coefficients, external-store-load parameters, external-store fin loads, and wing-panel aerodynamic loads are provided.

Report presenting the use of the slender-wing-type analysis to obtain general expressions for the surface pressure, lift, and rolling moment for cambered wings with swept trailing edges. The results are specialized to give the additional loading due to the deflection of trailing-edge control surfaces and the loading due to a particular type of wing twist. A numerical example for aileron control is included.

Report presenting testing of two blunt-nose models, a flat-face-cone and a hemisphere-cone, at Mach numbers up to 4.7. The main purpose was to determine information about heating rates and transition for different blunt nose shapes for long-range ballistic missiles. Information about pressure measurements and heat transfer is provided.

Low cowl drag, external compression inlet with subsonic dump diffuser for high Mach number application.

Report presenting an investigation of a zero-cowl-drag, all-external-compression inlet with an abrupt area discontinuity or subsonic dump diffuser for high Mach number application. Results regarding the diffuser performance characteristics, effect of spike retraction, a comparison with other inlets, and some theoretical calculations related to the results are provided.