"The subject of beam loading in linear electron accelerators has been discussed. With suitable design it is possible to place the equilibrium electron phase angle well ahead of the crest of the traveling wave in the accelerator. With beam loading the equilibrium position will move toward the crest, but the electron energy will remain constant or nearly so over a considerable range of loading. Some loss in energy will result from moving the equilibrium phase angle off the wave crest but the spread in energies due to beam loading should be reduced.

"A convenient summary is given of useful formulas on the kinematics of high energy electron scattering together with a derivation of the relevant formulas for transforming from the center of mass to the laboratory system such parameters as scattering cross sections. The formulas derived hold for any two- body collision: the approximation (m = 0) employed for the electron scattering calculations is rigorously true for the elastic scattering of photons."

"The phase and amplitude functions describing the betatron oscillations in the synchrotron are calculated using the revised parameters of the Cambridge Electron Accelerator. The results are given numerically and plotted in a graph for one machine period."

Monthly magazine discussing natural resources, parks, hunting and fishing, and other information related to the outdoors in Texas.

During the development of in-reactor corrosion experiments three types of bomb designs have been developed for following quantitatively the consumption of oxygen in a bomb which is fabricated from the particular metal under test. The bombs are designed so as to be rocked continuously during their in-reactor exposure, consequently agitating the uranium salt solution contained in the bomb and permitting gentle movement of the solution past metal specimens and other corroding surfaces. The oxygen pressure is produced within the bomb at the beginning of the run either by the withdrawal of gas from an oxygen tank or by the decomposition of hydrogen peroxide added just prior to closure. Temperature measurements are obtained by mans of thermocouples placed in a well within the bomb body or, in the latest design, there will also be thermocouples staked at several points on the outer wall of the bomb. The assembly is inserted in an experimental access hole in the reactor, brought up to a predetermined operating temperature by means of an electric furnace in close contact with the bomb, and allowed to remain for the desired amount of exposure to reactor radiation. Periodic measurements of temperature and pressure are made and the bomb …

Results of previous toroid tests with 28 micro 1600 fired ThO2 spheres are analyzed. Four possible explanations for the essentially zero attack rates are offered and discussed: peculiar motion of toroids or some unknown wall effect; rotational hydrodynamic forces cushioning the particle impact; the bed was not in suspension and not sliding over the walls of the toroid; round particles are not as erosive to oxide film surface as sharp pointed particles.

Calculations indicate that it is impossible, even at high oxygen injection rates, to insure an excess of oxygen in the HRT fuel solution if the bubble letdown rate is more than 1 or 2 liters per minute. If, on the other hand, no bubbles are allowed to form, a reasonable excess oxygen concentration can be maintained with an oxygen injection rate which would not tax the capacity of the off-gas system. The xenon poison will be reduced to less than 2% by liquid letdown alone, and if an iodine absorption bed is installed below the catalytic recombiner, the xenon poison should be less than 1% without any bubble letdown. Therefore, it is recommended that sufficient copper be added to prevent the formation of gas bubbles and that the oxygen injection rate be limited to a value which would permit adequate holdup times in the present charcoal adsorption beds, assuming this quantity is sufficient to meet corrosion requirements.

Stress corrosion was found in 8 components of the HRT mockup; only of four of these actually shut down the loop. All of the failures have occurred in the high-pressure system of the loop.

The leak detector system consists of one gas pressurized reservoir containing heavy water, a tubing manifold connecting the pressurizer to six separate lines each connected to one of the flanges, tubing lines leading from the second hole on each of three flange pairs (dome and heat exchanger flanges) back into the instrument room, plus required valves and fittings. A schematic diagram of the system in included.

The operation of the HRT mockup was on 0.042m UO2SO4, 0.024m H2SO4, and 0.005m CuSO4 at 280 C and 1400 psi pressure. with the O2 content at near 500 ppm. The pump showed bearing wear and high corrosion. The letdown heat exchanger was removed from the mockup and sectioned. The metallographic examination revealed corrosion. Results of corrosion runs on Ti, zircaloy-2, and stainless steel are given.

Preliminary results of tests wit the Westinghouse 100A pump indicate that Al2)3 and tungsten carbide coated bearing-journal assemblies prepared by the Linde process are not promising as substitutes for the graphitar-stellite combination. The front Al2O3 assembly failed at start-up with water and both front and rear tungsten carbide assemblies failed after 121 hours with water at 245 C.

General considerations involving the transportation of irradiated fuel and radioactive wastes are reviewed. It is assumed that many reactors will supply feed to a few large multipurpose chemical plants which ultimately send radioactive waste to a few disposal sites. General economic considerations of irradiated fuel reprocessing, economic aspects of the nuclear economy complex, growth predictions of the nuclear power economy in the U.S., general requirements for the shipment of fuel and waste, regulations applicable to fuel shipment, and permissible radiation levels are discussed.

This technical report described the formulation of a set of two-group neutron diffusion equations and the solution for the critical fuel cross section in a one-dimensional, multi-region spherical reactor. A subsequent report will describe the ORACLE code developed for survey calculations using this method.

Monthly newsletter of the High Plains Underground Water Conservation District No. 1, discussing the field of underground water. Topics include profiles of water conservation research, annual pre-plant soil moisture survey data, annual Winter Water Level measurement data, and information about the latest water conservation tips.

Monthly journal about library issues in Texas including collection development, programming and activities, managements, and other topics of interest.

"The Purpose of this paper is to present a preliminary discussion of the stratigraphy of the park city and phosphoric formations with special emphasis on the phosphatic parts and to discuss the distribution of phosphate in Utah. The Mississippian deposits are discussed only briefly because of the lack of new data concerning them"

Illustrations, including maps, accompanying a report detailing a ground check of faults and joints in the San Rafael Swell in Emery County, Utah. Fault and joint trends, direction of fault displacements, and some instances the amount of displacement, were mapped.

This report presents field reconnaissance results and office study of available data pertaining to the Cedar Mountain area, Emery County, Utah, and is part of a series of reports synthesizing the geologic relations of uranium deposits in all formations on the Colorado Plateau.

Discussing the potential for Mexico to be used as a uranium source.

Discussing a reconnaissance, in the uppermost Cretaceous and early tertiary rocks of the eastern San Juan Basin, New Mexico, for uranium

Discussing major joint trends in the Circle Cliffs area, in Garfield County, Utah.

Discussing a ground check of faults and joints made in the San Rafel Swell in Emery County, Utah.

A monthly report summarizing work perform by Babcock & Wilcox personnel for the U.S. Atomic Energy Commission. This month's report includes the Research and Development program was completed, a study of shielding requirements indicated the necessity for test data, more information on studies regarding reactor startup, and other developments related to develop the LMFRE.

None