Report presenting the zero-lift wave drag of a particular family of unswept, tapered wings with linearly varying thickness ratio and symmetrical parabolic-arc sections. It is found that the variable-thickness-ratio wings can be used to advantage with no serious structural penalties if the wings have the same given root thickness ratio or internal volume. Results regarding the given frontal area and given volume are provided.

Note presenting an investigation of three NACA 1-series nose inlets, two of which were fitted with protruded central bodies, was conducted in the 8-foot high-speed tunnel. An elliptical-nose body which had a critical Mach number approximately equal to that of one of the nose inlets, was also tested. Results regarding the nose inlet characteristics and nose-inlet-central-body combinations are provided.

Note presenting the effect of pressure gradient, wall temperature, and Mach number on laminar boundary-layer characteristics and, in particular, on the skin-friction and heat-transfer coefficients, on the separation point in an adverse pressure gradient, on the wall temperature required for stabilization of the laminar boundary layer, and on the minimum critical Reynolds number for laminar stability.

Report presenting two-dimensional tests of eight 6-percent-thick symmetrical airfoils of the supersonic and subsonic types. Static pressures along the surfaces of each airfoil measured over a range of Mach numbers and angles of attack. Results regarding lift coefficient, drag coefficient, quarter-chord pitching-moment coefficient, and schileren photographs of the pressure distributions are provided.

"The effects of interaction between a landing gear and a flexible airplane structure on the behavior of the landing gear and the loads in the structure have been studied by treating the equations of motion of the airplane and the landing gear as a coupled system. The landing gear is considered to have nonlinear characteristics typical of conventional gears, namely, velocity-squared damping, polytropic air-compression springing, and exponential tire force-deflection characteristics. For the case where only two modes of the structure are considered, an equivalent three-mass system is derived for representing the airplane and landing-gear combination, which may be used to simulate the effects of structural flexibility in jig drop tests of landing gears" (p. 619).

"A general matrix method is developed for the solution of characteristic-value problems of the type arising in many physical applications. The scheme employed is essentially that of Gauss and Seidel with appropriate modifications needed to make it applicable to characteristic-value problems. An iterative procedure produces a sequence of estimates to the answer; and extrapolation techniques, based upon previous behavior of iterants, are utilized in speeding convergence. Theoretically sound limits are placed on the magnitude of the extrapolation that may be tolerated" (p. 747).

"The relationships between conditions of hot-working and properties at high temperatures and the influence of the hot-working on response to heat treatment were investigated for an alloy containing nominally 20 percent molybdenum, 2 percent tungsten, and 1 percent columbium. Commercially produced bar stock was solution-treated at 2,200 degrees F. to minimize prior-history effects and then rolled at temperatures of 2,200 degrees, 2,100 degrees, 2,000 degrees, 1,800 degrees, and 1,600 degrees F. Working was carried out at constant temperature and with incremental decreases in temperature simulating a falling temperature during hot-working" (p. 1).

"For calculation of the characteristic parameters of the boundary layer (momentum-loss thickness and form parameter for the velocity profile), two quadrature formulas are given which are valid for the laminar as well as for the turbulent state of flow. These formulas cover both the two-dimensional and the rotationally symmetrical case. The calculation of the momentum-loss thickness is carried out by a simple integration of the energy theorem" (p. 1).

From Summary: "An experimental investigation has been made in the Langley stability tunnel to determine the low-speed yawing, pitching, and static stability characteristics of a 1/10-scale model of the Grumman F9F-9 airplane. Tests were made to determine the effects of duct-entrance-fairing plugs on the static lateral and longitudinal stability characteristics of the complete model in the clean condition. The remaining tests were concerned with determining tail contributions as well as the effect of duct-entrance-fairing plugs, slats, flaps, and landing gear on the yawing and pitching stability derivatives. These data are presented without analysis in order to expedite distribution."

"During an investigation of the J57-P-1 turbojet engine in the Lewis altitude wind tunnel, effects of inlet-flow distortion on engine stall characteristics and operating limits were determined. In addition to a uniform inlet-flow profile, the inlet-pressure distortions imposed included two radial, two circumferential, and one combined radial-circumferential profile. Data were obtained over a range of compressor speeds at an altitude of 50,000 and a flight Mach number of 0.8; in addition, the high- and low-speed engine operating limits were investigated up to the maximum operable altitude" (p. 1).

"Some aileron load characteristics for three thin wings varying in sweep have been presented for Mach numbers from 0.80 to 1.05. For the transonic Mach number range, shock effects exert a large influence on the loading, but the exact location of each shock for a specific wing design cannot be cataloged at the present time. It is shown, however, that the aileron loading, although greater in magnitude than at subsonic speeds, nevertheless varies in as uniform a fashion as at subsonic speeds" (p. 1).

Report presenting an investigation to determine the possibility of using simplified procedures for the estimation of control loads at supersonic speeds. The results indicated that relatively simple procedures are possible for the estimation of loadings on flap-type controls at supersonic speeds for cases when no flow separation occurs ahead of the hinge line.

Report presenting a wind-tunnel investigation at subsonic Mach numbers up to 0.9 to measure the root-mean-square variation of the normal forces on 27 NACA airfoil sections. The effects of thickness-chord ratio, camber, location of minimum pressure, and leading-edge radius were investigated.

Report presenting a consideration of the problem of shaping an adjoining fuselage for a given wing and supersonic Mach number so that the combination will have a low wave drag. Only fuselages that can be simulated by singularities distributed along the body axis are studied.

Memorandum presenting the Bell X-5 research airplane tested at 58.7 degrees sweepback during the program to determine the characteristics of a variable-sweep fighter airplane at transonic speeds. This paper includes the stability and control characteristics in the stable lift range up to Mach numbers near 1.0 at an altitude of 40,000 feet and to slightly lower Mach numbers at altitudes of 25,000 feet and 15,000 feet. Results regarding general comments, static stability and control characteristics, and longitudinal dynamic stability are provided.

Report presenting an investigation of the blades of an experimental two-blade jet-driven helicopter when subject to a condition of near resonance between the frequencies of the first elastic bending mode of the blades and third harmonic component of the aerodynamic loading that results in high bending strains in normal flight conditions. Various changes in design configuration on the blade bending strains were explored. Results regarding the preliminary studies, effects of variation in flight conditions and blade configuration, and harmonic analysis are provided.

Note presenting an experimental investigation of the heat-loss characteristics of heated fine wires suitable for use as anemometers in turbulence research. The effects of each of the several variables on the heat-loss characteristics of both normally oriented and swept wires were measured. The temperature-loading effects were found to cause large sensitivity differences between constant-temperature and constant-current operation.

Report presenting an investigation in a free-jet facility of a ramjet engine with an experimental 48-inch-diameter combustor. Three combustor lengths, three lengths of the shroud which separated the bypass air from the burning stream, and four fuel-distribution systems were investigated over a range of fuel-air ratios and a range of engine air flows. Results regarding the engine performance and ignition data, effect of fuel profile on combustion efficiency, total-pressure ratio, and distribution of static pressure in the main air stream are provided.

Report presenting a wind-tunnel investigation to determine the effect of lowering the wing from the top of the fuselage to the bottom of the fuselage on the longitudinal characteristics of a wing-fuselage and a wing-fuselage-tail combination with the horizontal tail at various heights above the plane of the wing. The effects of wing height on the longitudinal characteristics of the model were small.

Report presenting an investigation to determine the effect of lowering the wing from the top of the fuselage to the bottom of the fuselage on the longitudinal characteristics of a wing-fuselage and wing-fuselage-tail combination with the horizontal tail at various heights above the plane of the wing. Testing occurred at a range of Mach and Reynolds numbers.

Report presenting an investigation in the 4- by 4-foot supersonic pressure tunnel at a Mach number of 1.41 to determine the static stability and control and drag characteristics of a model of a 35 degree swept-wing airplane. The effects of alternate fuselage shapes, wing camber, wing fences, and fuselage dive brakes on aerodynamic characteristics were also investigated.

Report presenting an investigation of the overall performance of a modified eight-stage axial-flow compressor as part of the investigation of the problems encountered in a high-pressure-ratio axial-flow compressor with transonic inlet stages. The maximum total pressure ratio obtained at design speed was 11.0 at an equivalent weight flow of 70.9 pounds per second with an adiabatic efficiency of 0.81. Results regarding modified compressor performance and comparison with predicted performance are provided.

Memorandum presenting rolling stability derivatives for a complete model with a low-aspect-ratio wing and tail surfaces for a Mach number range of 0.70 to 0.94 and for an angle-of-attack range from 0 to 13 degrees for the lower Mach numbers. The model test results indicated regions of neutral or unstable damping in roll at Mach numbers of 0.85 and 0.90 in the higher angle-of-attack range for the basic model. Results regarding damping in roll, yawing moment and lateral force due to rolling, and aileron characteristics are provided.

Report presenting some experimental and theoretical studies of axisymmetric free jets exhausting from sonic and supersonic nozzles into still air and into supersonic streams as a way to investigate problems associated with propulsive jets. A variety of variables for each case are considered, including jet Mach number, nozzle divergence angle, jet static-pressure ratio, free-stream Mach number, and specific heat ratios.