Note presenting an investigation to determine the fatigue-strength values for 24S-T aluminum alloy when subjected to various ratios of biaxial stresses. The stresses considered were both tensile. The results indicated that uniaxial fatigue-strength values in the longitudinal direction cannot be used to predict the fatigue strength, and that biaxial fatigue strength may be as low as 50 percent of the uniaxial fatigue strength.

Report presenting an investigation of pitching moments and center-of-pressure locations obtained from a landing investigation in smooth water of a conventional flying boat as compared to values predicted by general hydrodynamic impact theory. Landings were generally moderate and covered as wide a range of trim and velocities as practical. Results regarding the center of pressure and pitching moments are provided.

Note presenting a theoretical solution for the problem of the compressive buckling of flat rectangular Metalite type sandwich plates with simply supported loaded edges and clamped unloaded edges. The solution is based on the general small-deflection theory for flat sandwich plates developed in a previous report. Results regarding stability orientation and buckling curves, comparison with approximate solution, correction for plasticity, and comparison of theory and experiment are provided.

"A theoretical solution is presented for the critical axial-compressive stress of a simply supported curved rectangular panel having a central longitudinal stiffener offering no torsional restraint. The results are presented in the form of computed curves and tables. Because a panel of moderate or large curvature buckles in compression at a stress lower than the theoretical value, a method is suggested to aid in determining the critical stress for use in design" (p. 1).

Report presenting a study of the factors involved in the design of total-temperature probes for use at supersonic speeds as applied to the design of an instrument to be used in wind-tunnel calibrations. Tests of the probe showed that the calibration factor required in the conversion of the measured temperature to the true total temperature was 0.992 for a range of Mach numbers.

The problem of the motion of an elongated body of revolution in an incompressible fluid may, as is known, be solved approximately with the aid of the distribution of sources along the axis of the body. In determining the velocity field, the question of whether the body moves uniformly or with an acceleration is no factor in the problem. The presence of acceleration must be taken into account in determining the pressures acting on the body. The resistance of the body arising from the accelerated motion may be computed either directly on the basis of these pressures or with the aid of the so-called associated masses (inertia coefficients). A different condition holds in the case of the motion of bodies in a compressible gas. In this case the finite velocity of sound must be taken into account.

"For a certain Mach number of the oncoming flow, the local velocity first reaches the value of the local velocity of sound (M = 1) at some point on the surface of the body located within the flow. This Mach number is designated the critical Mach number M(sub cr). By increasing the flow velocity, a supersonic local region is formed bounded by the body contour and the line of transition from subsonic to supersonic velocity. As is shown by observations with the Toepler apparatus, at a certain flow Mach number M > M(sub cr) a shock wave is formed near the body that closes the local supersonic region from behind" (p. 1).

"When auxiliary jet engines are installed on airframes; as well as in some new designs, the jet engines are mounted in such a way that the jet stream exhausts in close proximity to the fuselage. This report deals with the behavior of the jet in close proximity to a two-dimensional surface. The experiments were made to find out whether the axially symmetric stream tends to approach the flat surface" (p. 1).

Describes different types of greenhouses for lettuce-growing; provides instructions for growing lettuce in greenhouses.

Note presenting an investigation conducted to determine the oxidation characteristics of molybdenum disulfide and to determine the effect of such oxidation on its role as a solid-film lubricant. A coating of molybdenum disulfide serving as a high-temperature solid-film lubricant maintained low coefficient-of-friction values during its oxidation as long as an effective subfilm of the molybdenum disulfide remained.

"Four component measurements of 12 wings of symmetric profile having flaps with chord ratios t(sub R)/t(sub L) = 0.3 and t(sub R)/t(sub L) = 0.2 are treated in this report. As a result of the investigations, the effects of plan form and gap between fixed surface and control surface have been clarified. Lift, drag, pitching moment, and hinge moment were measured in the control-surface deflection range: -23 deg < or = beta < or = 23 deg and the range of angle of attack: -20 deg < or = alpha < or = 20 deg" (p. 1).

The present report, which forms the first of six articles on experiments with airfoils of aspect ratio from 1 to 3 and various planforms, deals with the three- and six-component measurements made on the trapezoidal wing series in the 2.15 x 3-meter wind tunnel of the DVL at the request of the Henschel Aircraft Company.

Monthly magazine discussing natural resources, parks, hunting and fishing, and other information related to the outdoors in Texas.

None

Report discussing examination of various trace elements by the U.S. Geological Survey in Indiana, Illinois, Missouri, Arkansas, and Kentucky during October and November, 1946.

Report containing articles, manuscripts, and tabulations of recorded spectra created by the Spectroscopic Laboratory of the University of Chicago.

Report containing articles, manuscripts, and tabulations of recorded spectra created by the Spectroscopic Laboratory of the University of Chicago.

"The present report is concerned with a series of tests on a model airplane fitted with four types of dive flaps of various shapes, positions, and incidence located near the leading edge of the wing (from 5 to 20 percent of the wing chord). Tests were also made on a stub airfoil fitted with a ventral dive (located at 8 percent of the wing chord). The hinge moments of the dive flaps were measured" (p. 1).

An altitude-wind-tunnel investigation of the performance of AN-F-58 and AN-F-32 fuels in an experimental turbojet engine was conducted over a range of simulated altitudes and flight Mach numbers. Combustion efficiencies obtained with AN-F-58 and AN-F-32 fuels were approximately equal. The minimum-speed altitude operational limit was essentially the same with either AN-F-58 or AN-F-32 fuel. Starting characteristics of the two fuels were approximately the same at low wind milling speeds. Visual observation showed no apparent differences in the carbon-deposition rates of AN-F-58 and AN-F-32 fuels.

Memorandum presenting an approximate method for the estimation of the properties of the incompressible laminar boundary layer on a flat plate in the slip-flow region using Karman's momentum method. At equivalent stations, the total thickness and the skin friction of a slipping boundary layer are less than that of the normal boundary layer at the same Reynolds number.

The necessity of complete removal of all the radioactive isotopes of iodine was discussed in general terms in the document Iodine Conditions in Connection with Rain Production.'' It is the purpose of this document to enlarge upon this phase of operation. Calculations of maximum permissible dose of Iodine 131, 132, 133 and 135 have also been performed. 3 tabs.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Price Daniel, regarding a legal question submitted for clarification: Availability of the appropriation contained in Item 76 for the current fiscal year to the State Department of Agriculture for the purchase of automobiles.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Price Daniel, regarding a legal question submitted for clarification: Time of vesting of limitation title with reference to subdivision under Rule 37.

"An investigation has been conducted in the Langley 20-foot free-spinning tunnel of a 1/29-scale model of the Republic XF-91 airplane with a.conventional-tail arrangement installed. Previously, tests were made on the model with a vee tail installed. The erect spin and recovery characteristics of the model were determined for the normal loading with the wing installed at various amounts of incidence. The spin investigation also included inverted-spin tests, spin-recovery-parachute tests, tests with the center of gravity moved rearward, and tests with external fuel tanks added to the model" (p. 1).