From Introduction: "The present paper deals with control surfaces having plain-overhang and Frise balances."

From Introduction: "As a part of the general lateral-control investigation by the NACA, the large amount of two- and three-dimensional data on the rolling effectiveness of ailerons without exposed overhang balance is collected and analyzed in the present paper."

From Summary: "This paper deals with the single problem if circular shell-supported frames subjected to concentrated loadings. A mathematical attack is developed and presented in the form of nondimensional-coefficient curves."

This report is a copy of a letter sent on May 23, 1944, concerning the analytical evaluation of Columbia River water by Clinton Laboratories.

From Summary: "The results of an analytical investigation to determine the qualitative effects of elevator-fabric distortion on the stick-force characteristics of an airplane are presented. These results indicate that serious alteration of intended stick-force characteristics can be produced by elevator-fabric distortion."

Report presenting a device that automatically analyses the data from a 45 degree strain rosette. The rosette strains are properly combined by means of an electric circuit to yield a direct meter reading of maximum shear strain and major and minor principal strains.

Report discusses an analysis and preliminary design of a control linkage that varies automatically with dynamic pressure. The advantages of the device, including greater lateral control than a fixed control linkage without additional aerodynamic balance, are detailed. The effect of variable linkage on lateral-control characteristics is also described.

Warping of a rod by a variation in heat transfer coefficient around the periphery is considered. Estimates for some simple cases are given, and a more precise numerical calculation is carried out in ne instance.

From Summary: "Charts are presented for rapidly determining the principal strains and stresses, the maximum shear strain and stress, and the orientation of principal axes from data on 45 degree strain rosettes. The charts may be used for analyzing the conventional data consisting of strains measured along three gage lines 45 degrees apart, but their application is more direct if the rosette data are obtained by means of special circuits that require the use of four gages 45 degrees apart."

Abstract: "The advantages of high scaling ratios in counting random pulses are discussed. The mechanism of the basic circuit used in the Columbia University scaling circuits is described. The difficulties experienced in the performance of the earlier circuits are indicated and modified circuits to eliminate these difficulties are given. Precautions that must be observed in carrying out the constructional details are suggested. The complete circuit and specifications are given in detail for a Scale of 128 for use with linear-amplifier systems" (p. 1).

Report presenting an investigation of the cooling of a Franklin 6-AC-29S horizontally opposed cylinder air-cooled engine installed in a Fleetwings model 33 trainer. The cowling on the airplane did not provide satisfactory cooling, but several alterations were tested, including with cylinder baffles. Results regarding engine cooling, aerodynamics of the cowling installation, and predicted versus actual cowling performance are provided.

It is usual to determine the density of neutrons by using foils of metals which become radioactive as a result of bombardment in the region under investigation. From the rate of disintegration of the newly formed radioactive element the number of neutrons absorbed can be calculated. By use of the capture cross section of the element of which the foil is composed the density of the neutrons can then be computed. By counting the alpha particles from a bismuth foil of known weight after exposure to neutrons the density of the neutrons which produced this activity can be calculated. The least accurately known value which enters into this evaluation is the capture cross-section of bismuth for pile neutrons. This value may be improved by future measurements. It is of importance only for absolute measurements of neutron density so that relative values can be measured with considerable accuracy on the basis of known data.

Measurements made in a uranium cylinder result in a mean value of 1.55 cm. for the diffusion length L for distances of 1 to 4 cm. from the base of the cylinder. Calculations give a value which agrees with the experimental result and show further that L increases from 1.40 to 1.63 cm. as the neutrons diffuse a distance of 5 cm. into the uranium.

"The effects of changes in aileron rigging between 2 deg up and 2 deg down on the stick forces were determined from wind-tunnel data for a finite-span wing model. These effects were investigated for ailerons deflecting equally in both directions and linearly with stick deflection. Data were analyzed for a Frise, a sealed internally balanced, and a beveled-trailing-edge aileron" (p. 1).

"The results of a series of tests to determine the effect of internal pressure on the buckling load of a thin cylinder under an applied torque indicated that internal pressure raises the shear buckling stress. The experimental results were analyzed with the aid of previously developed theory and a simple interaction formula was derived" (p. 1).

"The effect on static-pressure measurements of locating a pitot-static tube 0.55 chord ahead of an airfoil section has been investigated. The tests were conducted in the NACA 24-inch high-speed tunnel on airfoil sections of various thickness ratios over a large range of Mach number. The results show that for a wing having a thickness ratio of 0.15 the measured Mach number, determined from a pitot-static-tube reading, is approximately 0.01 too low at a stream Mach number of 0.4 and approximately 0.03 too low at a Mach number of 0.8" (p. 1).

Report discusses the "effects of oil introduced into the combustion chamber and of oil-spray piston cooling on the knock-limited performance of aircraft engines" (from Summary). A CFR engine and Allison V-1710 cylinder were used to test the rate of oil consumption, knock, and knock-limited brake mean effective pressure.

Report presenting methods for estimating pressure distributions over protuberances such as cockpit canopies, gun turrets, blisters, scoops, and sighting domes. The methods are applied to the estimation of the pressure distributions over spherical segment and faired gun turrets and over the protuberances on the Brewster SB2A-1 airplane. The effects of compressibility, interference, and flow separation are discussed.

"An experimental investigation of rectangular exhaust-gas ejector pumps was conducted to provide data that would serve as a guide to the design of ejector applications for aircraft engines with marginal cooling. The pumping characteristics of rectangular ejectors actuated by the exhaust of a single-cylinder aircraft engine were determined for a range of ejector mixing-section area from 20 to 50 square inches, over-all length from 12 to 42 inches, aspect ratio from 1 to 5, diffusing exit area from 20 to 81 square inches, and exhaust-nozzle aspect ratio from 1 to 42" (p. 161).

Report includes tension fatigue test results on the following types of samples of 0.040-inch alclad 24s-t: (1) monoblock sheet samples as received and after a post-aging heat treatment, (2) "sheet efficiency" samples (two equally stressed sheets joined by a single transverse row of spot welds) both as received and after post-aging, (3) spot-welded lap-joint samples as received and after post-aging, and (4) roll-welded lap-joint samples. (author).

Field measurements were made on a fighter airplane to determine the approximate magnitude of the horizontal tail loads in accelerated flight. In these flight measurements, pressures at a few points were used as an index of the tail loads by correlating these pressures with complete pressure-distribution data obtained in the NACA full-scale tunnel. In addition, strain gages and motion pictures of tail deflections were used to explore the general nature and order of magnitude of fluctuating tail loads in accelerated stalls.

"Field measurements were made on a fighter airplane to determine the approximate magnitude of the horizontal tail loads in accelerated flight. In these flight measurements, pressures at a few points were used as an index of the tail loads by correlating these pressures with complete pressure-distribution data obtained in the NACA full-scale tunnel. In addition, strain gages and motion pictures of tail deflections were used to explore the general nature and order of magnitude of fluctuating tail loads in accelerated stalls" (p. 351).

The uranium metal, as discharged from the piles in the 100 Areas, contains the alpha emitting product, plutonium, in concentration in the neighborhood of 150--250 grams per metric ton, along with similar amounts of beta and gamma fission elements. It is the purpose of the Separations Plant to effect the separation of this product from the uranium metal and fission elements, and to prepare a concentrated, relatively pure solution of plutonium nitrate as the final product of the Hanford Plant. This section of the manual discusses the chemistry of the separations process, describes the buildings and equipment provided for carrying out the various steps in the operation, and presents the detailed operating procedures used. There are included, in many instances, references to other documents presenting a more detailed view of a specific point in the process.

Report discusses measurements of the relaxation time of steam and nitrogen due to their importance as turbine-working fluids. Additional calculations regarding different nozzle lengths are included.