Report discusses measurements of the relaxation time of steam and nitrogen due to their importance as turbine-working fluids. Additional calculations regarding different nozzle lengths are included.

Report presenting the results of tests of a circular fuselage with various combinations of tail lengths and vertical tail surfaces with and without the horizontal tail surface in the 6- by 6-foot test section of the stability tunnel in the form of diagrams of variation of coefficients of lateral force and yawing moment with angle of yaw and angle of attack.

Report presenting an investigation to determine the knock-limited performance in a full-scale aircraft-engine cylinder of leaded blends of 10 pure hydrocarbons and a base fuel.

Report discusses the results of testing to determine the maximum rates of control stick (elevator) motion and corresponding maximum stick forces that could be exerted based on experiments with several pilots. The main topics explored were the comparison of the maximum rates of push and pull, maximum rates of push and pull when a mental restriction was placed on the pilot, and maximum rates at which the pilot though he would apply the elevator control forces versus the actual application of forces. Information about experimental procedures and the rig the testing occurred on is included.

Report presenting a method for predicting the amplitude and frequency, under certain simplifying conditions, of the hunting oscillations of an automatically controlled aircraft with lag in the control system or in response of the aircraft to the controls. Formulas are given expressing the response to a variation of signal in terms of response to a unit signal.

Results of flight tests indicate that profile-drag coefficients which were obtained with the low-drag airfoils were lower than with the conventional types over the range of light coefficients tested. For comparable conditions of the lift coefficient and Reynolds Number, the low-drag airfoils have profile-drag coefficients which may be 27 percent lower than the profile drag of the conventional airfoils tested. Detailed results are presented graphically.

From Summary: "A method is outlined for determining in flight the weight rate of air flow to the engine equipped with a Bendix-Stromberg injection-type carburetor. The method has the advantage that no additional equipment need be inserted in the charge-air system and only a few simple measurements are necessary. The analysis of an air-box calibration of the carburetor to be used in interpreting the flight measurements is shown by an example."

"A study was made of the performance of a jet-propulsion system composed of an engine-driven blower, a combustion chamber, and a discharge nozzle. A simplified analysis is made of this system for the purpose of showing in concise form the effect of the important design variables and operating conditions on jet thrust, thrust horsepower, and fuel consumption. Curves are presented that permit a rapid evaluation of the performance of this system for a range of operating conditions" (p. 1).

"Strain surveys were made on the stringers reinforcing a D-section box loaded in torsion and restrained from warping at the root. On the basis of the tests, a procedure is suggested for estimating the bending stresses due to torsion that occur near the flange of a D-section box. A similar test of a triangular-section box showed that for such a section there were no significant bending stresses due to torsion, a fact which was also shown theoretically" (p. 1).

"The design of curved sheet panels to resist shear involves a consideration of several factors: the buckling resistance of the sheet, the stress at which buckling becomes permanent, and the strength which may be developed beyond the buckling limit by tension-field action. Although some experimental as well as theoretical work has been done on the buckling and tension-field phases of this problem, neither of these types of action appears to be very well understood. This report presents the results of the first series of torsion tests of stiffened circular cylinders to be completed in connection with this study at Aluminum Research Laboratories" (p. 1).

Report presenting the results of aerodynamic tests of seven-blade propellers which were considered as a possible arrangement to avoid vibration difficulties. Variations of relative blade angle and rotational speeds of the front and rear components of a six-blade dual-rotating propeller were also investigated.

Report presenting tests on a scale model of a four-engine transport airplane to determine the stability characteristics, empennage control-surface effectiveness, the effect of propeller rotation on longitudinal stability, and a method for carrying spare wing panels under the fuselage. The effect of two models of wing power operation on the characteristics of the model was studied. The results indicate that the model possess satisfactory stick-fixed longitudinal stability for all normal flight conditions except for high power with flaps extended.

The results of this analysis indicate that isothermal pressure losses can be predicted analytically in the type of ducting system which may be broken down into the elementary forms of elbows, diffusers, and straight ducts for which pressure-loss data are published.

"The knock-limited performance of blends containing General Motors triptane in S reference fuel and in an S plus M base fuel was determined in 17.6, F-3, F-4, and full-scale (single cylinder) engines. The results obtained are presented and are compared with published data from similar tests of 12 aromatics, 10 paraffins (including highly purified triptane), and 2 olefins. The comparison of fuels - which is based on a consideration of (a) antiknock blending sensitivity, (b) lead susceptibility, (c) temperature sensitivity, and (d) comparison of small-scale and full-scale engine data - is presented by means of bar graphs" (p. 1).

Report presenting a method of correlating the effects of compression ratio and inlet-air temperature on the knock limits of aviation fuels. Knock-limited performance tests of several fuels were run to check the method.

Report presenting an investigation to determine the effect of the amount of oil flow to the piston on the ring-sticking characteristics of a piston and ring assembly and on the engine oil consumption. Results regarding the blow-by, lubrication, oil consumption, and method of supplying oil are provided.

Report presenting a method for making lifting-surface calculations by means of magnetic measurements of an electromagnetic-analogy model. The method is based on the perfect analogy between the strength of the magnetic field around a conductor and the strength of the induced-velocity field around a vortex.

Report presenting tests conducted to determine the performance of two pressurized shunt-type cooling systems for liquid-cooled aircraft engines using a mixture of 30 percent AN-E-2 ethylene glycol and 70 percent water as the coolant. Results regarding effect of engine speed on coolant-flow rate, effect of expansion-tank pressure on coolant-flow rate, relation between pump-inlet pressure and expansion-tank pressure, variation of coolant-flow rate with pump-inlet pressure, flow rate through the shunt lines, effect of coolant-flow rate on pressure drop, effect of venturi on performance of the cooling system, and the system operating experience are provided.

Report presenting an experimental investigation of rectangular exhaust-gas ejector pump to provide data that would serve as a guide to the design of ejector applications for aircraft engines with marginal cooling. With a decrease in the quantity of air pumped and an increase in the length of an ejector, the ejector pressure rise increases to optimum values. Results regarding straight ejectors, diffuser ejectors, curved ejectors, ejector aspect ratio, divided ejectors, multistage ejectors, and nozzle-exit effects are provided.

Report presenting an investigation of the effect of compressibility on the drag of a Bell P-39N-1 airplane in flight as part of a drag study on several high-speed airplanes for a range of Mach numbers.

Report discussing the changes in static longitudinal stability due to tilting the propeller axis of an SB2C-3 airplane downward. Tilting the propeller was found to be beneficial for stability, but only if the pilot was in a forward center-of-gravity position with a tilted engine. Installing a tilted engine reduced trim forces due to the changes in power up to 25 percent.

Report presenting a flight investigation made to determine the effectiveness of dive-recovery flaps installed on the XP-51 airplane as a safety device for recovery from contemplated terminal-velocity dives. The flap installation is described and results are presented of measurements obtained during stick-free pull-ups and pull-outs made by deflecting the dive-recovery flaps to two selected values of flap angle .

Report discusses the results of an investigation to determine the feasibility of using the change in the specific gravity of fuels in aircraft fuel tanks to measure fuel-vaporization loss. Six fuels were tested via fuel-distillation tests and simulated-flight tests. An equation based on the specific gravity of the fuel is also described.

Report presenting flight tests conducted to evaluate the effect of a thermal ice prevention system on the aerodynamic performance of a C-46 cargo airplane. The installation of the thermal ice-prevention system was found to reduce the indicated airspeed by about 6 miles per hour. Results regarding the overall performance change resulting from the installation of the thermal system, reduction of power attributed to heat-exchanger exhaust-gas back pressure, reduction of power attributed to the internal and external drag of the thermal system, and the additional airplane gross weight attributed to the thermal system are provided.