Report discusses the results of testing to determine the maximum rates of control stick (elevator) motion and corresponding maximum stick forces that could be exerted based on experiments with several pilots. The main topics explored were the comparison of the maximum rates of push and pull, maximum rates of push and pull when a mental restriction was placed on the pilot, and maximum rates at which the pilot though he would apply the elevator control forces versus the actual application of forces. Information about experimental procedures and the rig the testing occurred on is included.

From Introduction: "The present paper deals with control surfaces having plain-overhang and Frise balances."

Report discusses an analysis and preliminary design of a control linkage that varies automatically with dynamic pressure. The advantages of the device, including greater lateral control than a fixed control linkage without additional aerodynamic balance, are detailed. The effect of variable linkage on lateral-control characteristics is also described.

Report presenting measurements made of the pressures of the tail surfaces of the Republic Aviation Corporation P-47B airplane in the full-scale tunnel. Pressures were measured over the horizontal and vertical tail surfaces for several angles of attack and angles of yaw with numerous control-surface deflections to provide a check on the design loads. Results regarding the normal-force coefficients and predictions of forces on horizontal tail surfaces are provided.

From Introduction: "As a part of the general lateral-control investigation by the NACA, the large amount of two- and three-dimensional data on the rolling effectiveness of ailerons without exposed overhang balance is collected and analyzed in the present paper."

Report presenting a flight investigation made to determine the effectiveness of dive-recovery flaps installed on the XP-51 airplane as a safety device for recovery from contemplated terminal-velocity dives. The flap installation is described and results are presented of measurements obtained during stick-free pull-ups and pull-outs made by deflecting the dive-recovery flaps to two selected values of flap angle .

Report presenting methods for estimating pressure distributions over protuberances such as cockpit canopies, gun turrets, blisters, scoops, and sighting domes. The methods are applied to the estimation of the pressure distributions over spherical segment and faired gun turrets and over the protuberances on the Brewster SB2A-1 airplane. The effects of compressibility, interference, and flow separation are discussed.

Porpoising characteristics were observed on V-body fitted with tail surfaces for different combinations of load, speed, moment of inertia, location of pivot, elevator setting, and tail area. A critical trim was found which was unaltered by elevator setting or tail area. Critical trim was lowered by moving pivot either forward or down or increasing radius or gyration. Increase in mass and moment of inertia increased amplitude of oscillations. Complete results are tabulated and shown graphically.

Report presenting flight tests made with a modified Ryan ST airplane to determine the effect on aileron characteristics of various arrangements of balanced split flaps covering that portion of the wing span occupied by the ailerons. With the flaps fully extended, the aileron effectiveness was reduced by approximately 18 percent of the effectiveness measured with ailerons alone.

"The effects of changes in aileron rigging between 2 deg up and 2 deg down on the stick forces were determined from wind-tunnel data for a finite-span wing model. These effects were investigated for ailerons deflecting equally in both directions and linearly with stick deflection. Data were analyzed for a Frise, a sealed internally balanced, and a beveled-trailing-edge aileron" (p. 1).

Report discussing several types of jet-exit designs, including normal, beveled, and unsymmetrical shapes, and their effect on the stability characteristics of the aircraft. No deviation of the jet center line from its exposed path is likely to be obtained if a jet exist is used that is normal to the flow. Having a tilted or asymmetrical exit was found to adversely affect the stability of the aircraft.

From Summary: "The results of an analytical investigation to determine the qualitative effects of elevator-fabric distortion on the stick-force characteristics of an airplane are presented. These results indicate that serious alteration of intended stick-force characteristics can be produced by elevator-fabric distortion."

Report presenting a procedure for determining the motions of an airplane resulting from the deflection of the lateral or directional controls for the case of non-linear derivatives. A simple computation table is presented to illustrate the application of the procedure.

Report discusses the results of shear testing in which the heads of Du Pont explosive countersunk rivets were allowed to protrude above the skin surface before expansion and the protruding portions were removed after expansion. As the height of the rivet head above the skin increases, the tightness of the rivet was found to increase. The report concludes that it may be desirable to investigating filling an entire shank with an explosive charge in order to permit greater tolerances in the drilled hole diameter and still have consistently tight rivets.

Report presenting formulas for propellers for the rate of change of side-force coefficient with angle of yaw and for the rate of change of pitching-moment coefficient with angle of yaw. Charts of side-force derivatives are given for two propellers of different plan forms.

Report presenting an investigation to determine the effect of the amount of oil flow to the piston on the ring-sticking characteristics of a piston and ring assembly and on the engine oil consumption. Results regarding the blow-by, lubrication, oil consumption, and method of supplying oil are provided.

Report discussing the characteristics of the jet-motor air-intake duct system for a pursuit-type airplane with modifications to the duct system. Details of its effects on the Mach number, high pressure recovery, drag, and simplicity of the system are provided. Problems regarding the flow condition through the ducts and some potential modifications to prevent further issues are also described.

Report presenting testing of a representative bomber nacelle on a low-drag wing in the NACA two-dimensional tunnel. The adverse or interference effects of the nacelle on the low-drag wing were small.

Report presenting testing in the high-speed wind tunnel to determine the drag characteristics of several types of radial-engine nacelle on a low-drag airfoil. The drag coefficients of nacelles incorporating cowling-nose shapes shown by previous tests to be efficient and afterbodies of adequate length were about the same magnitude as commonly obtained for comparable installations on conventional wings. Results regarding the reduction of data, effect of nacelles on lift, and pressures at wing-nacelle juncture are provided.

From Summary: "A method is outlined for determining in flight the weight rate of air flow to the engine equipped with a Bendix-Stromberg injection-type carburetor. The method has the advantage that no additional equipment need be inserted in the charge-air system and only a few simple measurements are necessary. The analysis of an air-box calibration of the carburetor to be used in interpreting the flight measurements is shown by an example."

Report presenting tests of a three-barrel pressure carburetor to determine the effect of nonuniformity of the air flow in the intake duct on the metering of the carburetor. Measurements were made in the air side of the metering system and in the carburetor barrels for a variety of flow distributions. Results regarding the metering pressure, altitude compensation, effect of throttle on the metering characteristics, and flow of air around the bends are provided

Report discussing a mock-up injection impeller created to investigate the hydraulic characteristics and limitations of the NACA injection impeller currently in use. Information about the form and magnitude of critical factors of fuel-transfer leakage and peripheral fuel distribution is provided as well as the effects of design variations of components on hydraulic characteristics. Several revisions in portions of the impeller are suggested to improve its fuel-transfer, fuel-pumping, and fuel-equalizing characteristics.

"A method is developed for calculating the performance of a dual-rotating propeller from the section characteristics of the blade elements. The method is applied to an eight-blade dual-rotating propeller and the computed results are compared with low-speed wind-tunnel tests of the same propeller in both the tractor and pusher positions. The computations are found to agree within the experimental accuracy of the measurements" (p. 1).

An investigation was conducted to compare the performance of two 25-ft-diam rotors which had identical dimensions and were similar in construction but different in blade airfoil-sections. Tests were conducted at indicated blade pitch angles from 3 degrees to 11.5 degrees and rotor speeds of 200, 290, and 371 rpm. The 23012.6 rotor required 2 percent less power to hover than the 0012.6. At thrust coefficients above design, the performance of the 23012.6 became better than the 0012.6 rotor.