"A theoretical analysis of the cross-sectional temperature distribution of a water-cooled turbine blade was made using the relaxation method to solve the differential equation derived from the analysis. The analysis was applied to specific turbine blade and the studies icluded investigations of the accuracy of simple methods to determine the temperature distribution along the mean line of the rear part of the blade, of the possible effect of varying the perimetric distribution of the hot gas-to -metal heat transfer coefficient, and of the effect of changing the thermal conductivity of the blade metal for a constant cross sectional area blade with two quarter inch diameter coolant passages" (p. 1).

"An investigation has been conducted to determine whether three-dimensional flows may be utilized in axial-flow fan and compressor rotors so that the spanwise load distribution may be varied to obtain high pressure rise. Two rotors, one with approximately uniform and one with solid-body downstream tangential-velocity distributions, were designed and tested at the design blade angle" (p. 1).

Report presenting the results of testing in the transonic range of four flutter airfoils attached to a freely falling body. Failures of the airfoils were metered and recorded in order to determine the Mach numbers and altitudes of failure.

From Summary: "Tests of a 1/7 size model of the Grumman XJR2F-1 amphibian were made in Langley tank no.1 to examine the landing behavior in rough water and to measure the normal and angular accelerations experienced by the model during these landings. All landings were made normal to the direction of wave advance, a condition assumed to produce the greatest accelerations. Wave heights of 4.4 and 8.0 inches (2.5 and 4.7 ft, full size) were used in the tests and the wave lengths were varied between 10 and 50 feet (70 and 350 ft, full size)."

"A Douglas C-74 airplane, during a test dive at about 0.525 Mach number, experienced uncontrollable longitudinal oscillations sufficient to cause shedding of the outer wing panels and the subsequent crash of the airplane. Tests of a section of the horizontal tail plane from a C-74 airplane were conducted in the Ames 16-foot high-speed wind tunnel to investigate the possibility of the tail as a contributing factor to the accident. The results of the investigations of fabric-covered elevators in various conditions of surface deformation are presented in this report" (p. 1).

"An analysis has been made of the lift control effectiveness of a 20-percent-chord plain trailing-edge flap on the NACA 65-210 airfoil section from section lift-coefficient data obtained at Mach numbers from 0.3 to 0.875. In addition, the effectiveness of the plain flap as a lift-control device has been compared with the corresponding effectiveness of both a spoiler and a dive-recovery flap on the NACA 65-210 airfoil section. The analysis indicates that the plain trailing-edge flap employed on the 10-percent-thick airfoil at Mach numbers as high as 0.875 retains at least 50-percent of its low-speed lift-control effectiveness, and is sufficiently effective in lateral control application, assuming a rigid wing, to provide adequate airplane rolling characteristics" (p. 1).

"An analysis has been made of the lift-control effectiveness of a 20-percent-chord plain trailing-edge flap on the NACA 65-210 airfoil section from section lift-coefficient data obtained at Mach numbers from 0.3 to 0.875. In addition, the effectiveness of the plain flap as a lift-control device has been compared with the corresponding effectiveness of both a spoiler and a dive-recovery flag on the INCA 65-210 airfoil section" (p. 1).

"It is shown that for velocities slightly in excess of sonic, the position of detached shock wave located in front of a given body at zero angle of attack may be estimated theoretically to a reasonable degree of accuracy. In case of bodies of revolution the result was simple, but for two-dimensional bodies, pressure coefficient varies with Mach number, and slight difficulty appears. Theory developed compares favorably with available experimental data" (p. 1).

"At the request of the Air Material Command, Army Air Forces, an investigation was conducted by the NACA Cleveland laboratory to determine the performance characteristics of the compressor of the XJ-41-V turbojet engine. This report is the second in a series presenting the compressor performance and analysis of flow conditions in the compressor. The static-pressure variation in the direction of flow through the compressor and the location and the cause of the maximum flow restriction at an equivalent speed of 8000 rpm are presented" (p. 1).

Powered models of three different flying boats were landed in oncoming wave of various heights and lengths. The resulting motions and acceleration were recorded to survey the effects of varying the trim at landing, the deceleration after landing, and the size of the waves. One of the models had an unusually long afterbody. The data for landing with normal rates of deceleration indicated that the most severe motions and accelerations were likely to occur at some period of the landing run subsequent to the initial impact.

Report presenting a test-stand investigation conducted on a rectangular ramjet engine design for installation in an aircraft wing. The engine operated without excessive engine noise or vibration over the entire range of operating conditions. Results regarding inlet velocity, exhaust flame characteristics, fuel-air ratio, and total-temperature rise are provided.

In accordance with a request of the Bureau of Aeronautics, Navy Department, tests were performed in the Langley 20-foot free-spinning tunnel to determine the spin and recovery characteristics of a 1/24 scale model of the Grumman XTB3F-1 airplane. The airplane is a two-place, midwing torpedo bomber equipped with a tractor propeller and an auxiliary jet engine. The effect of control setting and movement on the erect and inverted spin and recovery characteristics of the model were determined for the normal loading.

Report presenting an investigation of two 10-foot-diameter three-blade propellers to determine the effect of swept-back blade tips on propeller aerodynamic characteristics. Results regarding the effect of swept-back tips on maximum efficiency and constant-power propeller operation are provided.

Memorandum presenting high-speed wind-tunnel testing to investigate the aerodynamic characteristics at subsonic speeds of two symmetrical double-wedge airfoil sections of 4- and 6-percent-chord thickness suitable for application to supersonic aircraft. Section coefficients of lift, drag, and quarter-chord pitching moment are presented for a moderate range of angles of attack at Mach numbers up to approximately 0.93. The double-wedge airfoil exhibits no characteristics other than those common to the usual subsonic profile which would contribute to unsteady or uncontrollable flight at subsonic speeds of aircraft employing such a section for lifting surfaces.

"A compilation of free-spinning-airplane model data on the spin and recovery characteristics of 111 airplanes is presented. These data were previously published in separate memorandum reports and were obtained from free-spinning tests in the Langley 15-foot and the Langley 20-foot free-spinning tunnels. The model test data presented include the steady-spin and recovery characteristics of each model for various combinations of aileron and elevator deflections and for various loadings and dimensional configurations" (p. 1).

Report discussing an investigation on the effect of engine skew on the directional and lateral control characteristics of a single-engine airplane with a single-rotating propeller. The estimated and test results showed an advantage to skewing the propeller, as it assists with overcoming inadequate rudder control in power-on flight and aileron control, especially with flaps deflected.

Report presenting testing of a standard turbojet engine by water injection at the inlet of the axial-flow compressor in the altitude wind tunnel. Engine performance at 7600 rpm was obtained over a wide range of water-air-pressure ratios and ram-pressure ratios. Results regarding the engine-component performance are also provided.

Report presenting part of the results obtained to determine the effects of compressibility at high Mach numbers on a model of the Bell XS-1 transonic research airplane. General trends that can be qualitatively analyzed for level-flight Mach numbers up to 0.93 are given. Results regarding force characteristics and a comparison of results with wing-flow investigation are also provided.

Wind tunnel tests haved been made at low speed to various small-scale models of swept-back, swept-forward, and yawed wings. Tests covered changes in aspect ratio, taper ratio, and tip shape.

Report discussing testing on a 42 degree swept-back wing to determine its low-speed aerodynamic characteristics in pitch and yaw at high Reynolds numbers. The main effect of increasing the Reynolds number was delayed wing stalling to higher angles of attack. Roughness on the wing leading edge also had a large adverse effect on lift, drag, and pitching-moment characteristics at higher Reynolds numbers.

From Summary: "An investigation was conducted to determine the coolant-flow distribution, the cylinder temperatures, and the heat rejections of the V-1650-7 engine . The tests were run a t several power levels varying from minimum fuel consumption to war emergency power and at each power level the coolant flows corresponded to the extremes of those likely to be encountered in typical airplane installations, A mixture of 30-percent ethylene glycol and 70-percent water was used as the coolant. The temperature of each cylinder was measured between the exhaust valves, between the intake valves, in the center of the head, on the exhaust-valve guide, at the top of the barrel on the exhaust side, and on each exhaust spark-plug gasket."

Report presenting wind-tunnel testing to determine the low-speed lift, drag, and pitching-moment characteristics of a 40 degree sweptback wing with high-lift and stall-control flaps and a fuselage with a fineness ratio of 10.2 to 1. Low, medium, and high-wing-fuselage combinations were tested at high Reynolds numbers. Results regarding the high-lift and stall-control flaps and wing-fuselage combinations are provided.

Report presenting tests of an NACA 4-(5)(08)-03 two-blade propeller in the 8-foot high-speed tunnel for blade angles of 45 and 60 degrees extending the Mach number range from that of previous tests of the propeller up to Mach number 0.913. When the forward speed was increased from a low value to a forward Mach number of 0.90, the loss in peak efficiency was found to be not more than 47 percent.

"The spin and recovery characteristics of the Curtiss-Wright XP-87 airplane, as well as the spin-recovery parachute requirements, the control forces that would be encountered in the spin, and the best method for the crew to attempt an emergency escape, are presented in this report. The characteristics were estimated rather than determined by model tests because the XP-87 dimensional and mass characteristics were considered to be noncritical and because data were available from model tests of several similar airplanes. The study indicated that the recovery characteristics of the airplane will be satisfactory for all loadings if the controls are reversed fully and rapidly" (p. 1).