Memorandum presenting a theoretical analysis of the supersonic flow about two-dimensional and three-dimensional axially symmetric models restricted by theoretical walls capable of removing the nose shock. Results regarding the supersonic-tunnel interference due to nonreflecting walls and supersonic-tunnel interference due to porous walls are provided.

Memorandum presenting a study of the performance of swirl-can combustor elements for an experimental short-length turbojet combustor utilizing hydrogen fuel at high-altitude operating conditions. Fuel was injected into each element through a tangential, sonic orifice that created a swirling fuel-air mixture within each element. Results regarding combustor blowout, combustion efficiency, outlet temperature distribution, and preliminary performance of multielement combustor are provided.

Memorandum presenting a turbojet engine with a two-stage turbine operated with pentaborane fuel continuously for 11.5 minutes at a simulated altitude of 55,000 feet at a flight Mach number of 0.8. The engine incorporated an NACA combustor designed specifically for use with pentaborane fuel. Results regarding oxide formation and deposition, engine operating point, effect of oxide deposits on component performance, effect of oxide deposition on overall performance, and some operational comments are provided.

Memorandum presenting results of a supersonic flutter investigation of three low-aspect-ratio control surfaces. Two controls were all-movable but the third had a fixed cutout. Results regarding the experiments and calculations are provided.

Memorandum presenting force-oscillation tests made in the 8-foot transonic pressure tunnel to investigate some effects of an overhang-type aerodynamic balance and of a flow spoiler on the dynamic hinge-moment characteristics of a full-span flap-type rudder on a 5-percent-thick, swept vertical fin of low aspect ratio. Test results how that the aerodynamic damping moment on the plain rudder becomes unstable near a Mach number of 0.975 and remains unstable to the maximum speed of the tests.

Report presenting performance of a two-dimensional external-compression inlet designed for various methods of inlet-engine matching up to Mach 3 at Mach 1.89 and Mach 0. Results regarding shock geometry, two-shock ramps, isentropic ramps, profiles, and cowl drag for the various Mach number tests are provided.

Memorandum presenting an investigation of the performance of inlet configurations with a forebody designed for isentropic external compression at a nominal Mach number of 5.6. At zero angle of attack, all the configurations yielded larger total-pressure recoveries than had previously been obtained with a single-conical-shock inlet. Results regarding the flow about the forebody, inlet performance, and performance comparisons are provided.

Memorandum presenting an investigation of hemispherical nose shapes of titanium, stainless steel coated with aluminum oxide, and uncoated stainless steel with lithium hydride and magnesium as internal coolants. Results regarding titanium models, stainless-steel models (uncoated), stainless-steel models coated with aluminum oxide, solution effects on the decomposition temperature of lithium hydride, effect of lithium hydride and magnesium on temperature measurements, and efficiency of models cooled with lithium hydride are provided.

Transonic flutter derivatives for unswept wing control surface configurations determined by pressure cell measurements. The control surfaces were mounted on a wing with an aspect ratio of 3, a taper ratio of 0.6, and a wing-thickness ratio of 0.06. Results regarding aerodynamic balance, vortex generators, splitter-plate configurations, and wedges are provided.

Memorandum describing an investigation using two airplanes, an F6F-3 and F-86A, each fitted with servo equipment for varying in flight the lateral and directional stability and handling characteristics, which have been flown by test pilots to simulate the predicted dynamic behavior of six prototype airplanes. The methods of simulation and the types and ranges of variables considered are presented and the results of the individual programs are discussed.

"A study has been made of a flare-cylinder configuration to investigate its feasibility as a reentry body of an intermediate range ballistic missile. Factors considered were heating, weight, stability, and impact velocity. A series of trajectories covering the possible range of weight-drag ratios were computed for simple truncated nose shapes of varying pointedness, and hence varying weight-drag ratios" (p. 1).

An investigation was conducted on a 35 deg swept-wing fighter airplane to determine the effects of several blunt-trailing-edge modifications to the wing and tail on the high-speed stability and control characteristics and tracking performance. The results indicated significant improvement in the pitch-up characteristics for the blunt-aileron configuration at Mach numbers around 0.90. As a result of increased effectiveness of the blunt-trailing-edge aileron, the roll-off, customarily experienced with the unmodified airplane in wings-level flight between Mach numbers of about 0.9 and 1.0 was eliminated, The results also indicated that the increased effectiveness of the blunt aileron more than offset the large associated aileron hinge moment, resulting in significant improvement in the rolling performance at Mach numbers between 0.85 and 1.0. It appeared from these results that the tracking performance with the blunt-aileron configuration in the pitch-up and buffeting flight region at high Mach numbers was considerably improved over that of the unmodified airplane; however, the tracking errors of 8 to 15 mils were definitely unsatisfactory. A drag increment of about O.OOl5 due to the blunt ailerons was noted at Mach numbers to about 0.85. The drag increment was 0 at Mach numbers above 0.90.

Report presenting an investigation at Mach numbers of 1.61 and 2.01 to determine the pressure distributions for a series of 20 controls on a 60 degree delta wing. Tests occurred at a range of angles of attack and control deflections. Results regarding basic pressure distributions, comparison of experimental and theoretical results, and experimental comparisons are provided.

"Investigations have been made in flight and in wind tunnels to determine which components of turbojet installations are most critical in icing conditions, and to evaluate several methods of icing protection. From these studies, the requirements necessary for adequate icing protection and the consequent penalties on engine performance can be estimated. Because investigations have indicated that the compressor-inlet screen constitutes the greatest icing hazard and is difficult to protect, complete removal or retraction of the screen upon encountering an icing condition is recommended" (p. 1).

Report presenting an investigation of the ejection release characteristics of the MB-1 rocket from the missile bay of a model of the Convair F-106A airplane with its fin tips retracted at a simulated altitude of 18,670 feet. Successful ejections of the rocket were made at supersonic speeds by applying a combination of ejection velocity and nose-down pitching moment at release.

Memorandum presenting an icing investigation conducted to determine the general de-icing and runback characteristics of three production samples of electric rubber-clad cyclic de-icing boots. The overall de-icing characteristics of two of the boots investigated were quite similar. Results regarding boot surface temperatures and general de-icing and runback characteristics are provided.

Report presenting an investigation of a model of the Republic F-105 airplane to determine the static longitudinal aerodynamic characteristics of a revised configuration. The revisions included a lengthened fuselage, a relocated canopy, a contoured fuselage afterbody, a ventral fin, and an enlarged vertical tail. Results regarding the effect of stores, effect of dive-brake flaps, effect of forebody modifications, gun blisters, and duct air bleed, and a comparison of the modified model with the original are provided.

A lightweight instrument that utilizes resistance-wire electric strain gases to measure propeller-shaft thrust has been developed. A wind-tunnel investigation on a propeller installed, on a single-engine pursuit airplane showed that the instrument gave a reliable indication of propeller-shaft thrust to an accuracy of +/-2 percent within its calibrated range. No attempt was made to determine the relation of indicated shaft thrust to net propeller thrust.

Report presenting an investigation of hot-pressed molbdenum disilicide bodies produced by industrial processes at a temperature of 2950 degrees and a pressure of 3000 pounds per square inch. Results regarding the short-time tensile strength, stress-rupture data, compression strength, air-corrosion resistance, hardness, coefficient of linear thermal expansion, thermal conductivity, and density are provided.

"A pneumatic probe based on continuity of mass flow through two restrictions separated by a cooling chamber was constructed to measure gas temperature at and beyond the limit of thermocouples. This probe consisted of a subsonic flat-plate orifice for the first restriction and a sonic-flow converging-diverging nozzle for the second restriction. The effect of variation in gas constants on the calibration is examined for common engine-exhaust gases" (p. 1).

"An investigation has been made of a partial-span model of the tail surface designed for use on the Hughes Falcon (MX-904) missile to determine the aerodynamic characteristics of the tail and elevator including elevator hinge moment. Data obtained at Mach numbers of 1.62 and 1.96 in the Langley 9- by 12-inch supersonic blowdown tunnel are presented for the condition where the tail was attached to a segment of the foreshortened body" (p. 1).

Report presenting the results of an investigation at supersonic speeds to determine the aerodynamic characteristics of a model of the North American MX-770 missile at several designated Mach numbers. No analysis is provided. Information about the longitudinal aerodynamic characteristics with trimmer and elevon deflected and lateral aerodynamic characteristics are described.

Memorandum presenting an experimental investigation of the pressure-recovery performance of a fixed-geometry, two-cone, two-drag inlet at Mach number 2.95. Low drag was achieved by use of an internally cylindrical cowl with rapid flow turning that was within 4 degrees of the wedge angle for shock detachment. Results regarding the inlet performance and evaluation of inlet performance are provided.

Report discussing the performance of an experimental quarter-sector annular combustor at conditions simulating supersonic flight of a cooled-turbine engine, as well as 20 different modification to the design. The final configuration was found to show no structural failures and little or no warping of liner parts after 40 hours of operation.