Memorandum presenting a study of an acceleration-limiting control on a turbojet engine in order to determine its feasibility as an acceleration control. A proportional-plus-integral type of controller was used in the investigation. Results regarding the one-loop control and two-loop control are provided.

Memorandum presenting an acceleration-limiting control used on a turbojet engine to study the feasibility of its use as an acceleration control. A proportional-plus-integral type of controller was used in this investigation. Results regarding one-loop control and two-loop control are provided.

Report presenting an investigation at Mach numbers of 1.61 and 2.01 to determine the pressure distributions for a series of 20 controls on a 60 degree delta wing. Tests occurred at a range of angles of attack and control deflections. Results regarding basic pressure distributions, comparison of experimental and theoretical results, and experimental comparisons are provided.

Report presenting an investigation at two Mach numbers to determine the pressure distributions for a series of 20 controls on a 60 degree delta wing. Thirteen controls were of the balanced tip type and seven of the controls were of the more conventional trailing-edge type. Results regarding the basic pressure distributions, comparison of experimental and theoretical results, and some experimental comparisons are provided.

Memorandum presenting lift and drag characteristics that have been determined in flight in the landing-approach configuration on 41 jet-propelled fighter-type airplane arrangements, including various wing boundary-layer-control installations. Minimum comfortable approach speeds for carrier-type landings were evaluated for these airplanes by four test pilots. Results regarding the presentation of data, methods for the prediction of minimum comfortable approach speed, reasons for limiting approach speed, comparison of flight and predicted approach speeds, and comparison of test pilots' and service pilots' approach speed are provided.

Report presenting lift and drag characteristics in the landing-approach configuration on 41 jet-propelled fighter-type airplane arrangements using flight testing. Minimum comfortable approach speeds were evaluated by four test pilots. Suggestions for achieving optimal speeds for approach under various conditions are also provided.

Memorandum presenting an experimental investigation to determine the effect on drag of applying the moment-of-area-rule modifications to wing-body combinations with various wing plan forms. The effect of mounting air-to-air type missiles on the wing-mounted bodies of revolution which are part of the moment-of-area-rule modification was also investigated.

Report presenting studies to determine the effect of sliding velocity and ambient temperature on the friction properties and endurance lift of thin lead monoxide coatings bonded to type 440-C martensitic stainless steel. Results regarding the effect of run-in on endurance life are also provided.

Report presenting an investigation of a pylon-mounted-store airplane configuration in the supersonic pressure tunnel at a Mach number of 1.61. Forces and moments of a complete wing-fuselage-store-pylon combination was measured for a variety of pylon-mounted store locations below the wing. Results regarding the effect of store position on the aerodynamic characteristics in pitch, effect of store position on the aerodynamic characteristics in sideslip, store fins and store tail cone, double-store installation, effect of pylon location, and relative contribution of store-pylon forces toward total force are provided.

Transonic flutter derivatives for unswept wing control surface configurations determined by pressure cell measurements. The control surfaces were mounted on a wing with an aspect ratio of 3, a taper ratio of 0.6, and a wing-thickness ratio of 0.06. Results regarding aerodynamic balance, vortex generators, splitter-plate configurations, and wedges are provided.

Report presenting a determination of transonic flutter characteristics from pressure cell measurements on control surfaces sinusoidally oscillated at an amplitude of plus or minus 1.08 degrees at frequencies from 5 to 30 cycles per second. Various control-surface configurations were investigated, including internal and external aerodynamic balance, vortex generators, a splitter-plate type of control surface, and superposition of triangular shaped wedges or tetrahedra along the rear portion of the control-surface chord.

Memorandum presenting an experimental investigation of the pressure-recovery performance of a fixed-geometry, two-cone, two-drag inlet at Mach number 2.95. Low drag was achieved by use of an internally cylindrical cowl with rapid flow turning that was within 4 degrees of the wedge angle for shock detachment. Results regarding the inlet performance and evaluation of inlet performance are provided.

Report presenting an investigation in an altitude test chamber using a turbojet engine equipped with an afterburner and ejector to compare directly two techniques of determining thrust that are both applicable to flight installations. One method uses a swinging uncooled rake at the ejector outlet while the other requires extensive instrumentation to measure the momentum forces of systems and the force on the internal surface of the ejector nozzle. Results regarding the swinging-rake technique and internal-pressure technique are provided.

"A study has been made of a flare-cylinder configuration to investigate its feasibility as a reentry body of an intermediate range ballistic missile. Factors considered were heating, weight, stability, and impact velocity. A series of trajectories covering the possible range of weight-drag ratios were computed for simple truncated nose shapes of varying pointedness, and hence varying weight-drag ratios" (p. 1).

Report presenting aerodynamic forces for an external-store installation on the Douglas D-558-II research airplane. Store-pylon, pylon-alone, and fin loads were determined during angle-of-attack and angle-of-sideslip maneuvers over a range of Mach numbers. Results regarding the side-force coefficients, normal-force coefficients, external-store-load parameters, external-store fin loads, and wing-panel aerodynamic loads are provided.

Report presenting testing of two blunt-nose models, a flat-face-cone and a hemisphere-cone, at Mach numbers up to 4.7. The main purpose was to determine information about heating rates and transition for different blunt nose shapes for long-range ballistic missiles. Information about pressure measurements and heat transfer is provided.

Low cowl drag, external compression inlet with subsonic dump diffuser for high Mach number application.

Report presenting an investigation of a zero-cowl-drag, all-external-compression inlet with an abrupt area discontinuity or subsonic dump diffuser for high Mach number application. Results regarding the diffuser performance characteristics, effect of spike retraction, a comparison with other inlets, and some theoretical calculations related to the results are provided.

Memorandum presenting an investigation conducted to measure and compare the total-pressure recovery and distortion characteristics at the compressor face of two single-place fighter-type airplanes with similar two-spool turbojet engines, but with dissimilar inlets. The total-pressure recovery was relatively independent of angle of attack and mass-flow ratio for both airplanes except for a significant decrease in pressure recovery with angle of attack for airplane B at the highest Mach numbers tested.

Report presenting an investigation to measure and to compare the total-pressure recovery and distortion characteristics at the compressor face of two single-place fighter-type airplanes with similar two-spool turbo-jet engines, but with dissimilar inlets. Results regarding compressor-face total-pressure surveys and surges encountered are provided.

Report discussing the use of hot-wire anemometers to measure circumferential traces of specific-mass-flow variation for various radial positions at the rotor exit. Results regarding the rotor blade-wake traces, relative total-pressure ratio, and centrifuging of low-momentum fluid are provided.

Memorandum presenting results of tests for possible flutter of a dynamically and elastically scaled model of a proposed all-movable horizontal tail surface for the North American X-15 airplane. Tests at Mach number 6.86 were made on the scaled model and on several other configurations with lower stiffnesses.

"Results of tests for possible flutter of a dynamically and elastically scaled model of a proposed all-movable horizontal tail surface for the North American X-15 airplane are presented herein. Tests at a Mach number of 6.86 were made on the scaled model and on several other configurations having lower stiffness. Flexibility influence coefficients and calculated modes and frequencies for the weakest configuration are presented" (p. 1).

Memorandum presenting results of a supersonic flutter investigation of three low-aspect-ratio control surfaces. Two controls were all-movable but the third had a fixed cutout. Results regarding the experiments and calculations are provided.