Report presenting testing at two engine speeds on six representative fuels rated at 100-octane number by the C.F.R. aviation method. Blends of the fuels with benzene, toluene, xylene, and isopropyl comprise nine other fuels, leading to testing on 15 fuels. Results regarding the tests at 2000 rpm and 250 degrees Fahrenheit inlet-air temperature, at 3100 rpm and 250 degrees Fahrenheit inlet-air temperature, 2000 rpm and 150 degrees Fahrenheit inlet-air temperature, and 3100 rpm and 150 degrees Fahrenheit inlet-air temperature, effect of speed on knock rating, effect of inlet-air temperature on knock rating, and effect of spark advance on knock rating are provided.

Report presenting tests of a three-barrel pressure carburetor to determine the effect of nonuniformity of the air flow in the intake duct on the metering of the carburetor. Measurements were made in the air side of the metering system and in the carburetor barrels for a variety of flow distributions. Results regarding the metering pressure, altitude compensation, effect of throttle on the metering characteristics, and flow of air around the bends are provided

Report presenting flight tests made with a modified Ryan ST airplane to determine the effect on aileron characteristics of various arrangements of balanced split flaps covering that portion of the wing span occupied by the ailerons. With the flaps fully extended, the aileron effectiveness was reduced by approximately 18 percent of the effectiveness measured with ailerons alone.

Report presenting a flight investigation to check the results of a theoretical analysis of longitudinal stability of an airplane with free controls. Tests used a Fairchild XR2K-1 airplane on which the weight moment and the aerodynamic balance of the elevator were varied to bring it into a condition where unstable short-period oscillations were encountered.

Report presenting the reasons for the existence of bending stresses due to torsion and the theoretical formulas applying to rectangular boxes with finite bulkhead spacing. Tests are described which were made to verify the theory, strains being measured on a rectangular torsion box with four bulkhead spacings. Results regarding normal stresses are provided.

Porpoising characteristics were observed on V-body fitted with tail surfaces for different combinations of load, speed, moment of inertia, location of pivot, elevator setting, and tail area. A critical trim was found which was unaltered by elevator setting or tail area. Critical trim was lowered by moving pivot either forward or down or increasing radius or gyration. Increase in mass and moment of inertia increased amplitude of oscillations. Complete results are tabulated and shown graphically.

Summary: The effective change in the velocity of flow past a wing section, caused by the presence of wind-tunnel walls, is known for potential flow. This theory is extended by investigation of the two-dimensional compressible flow past a thin Rankine Oval. It is shown that for a symmetrical section at zero angle of attack the velocity increment due to the tunnel walls in the incompressible case must be multiplied by the factor 1/1-M^2 to take account of compressibility effects. The Mach number, M, corresponds to conditions in the wind-tunnel test section with the model removed (p. 1.).

Report presenting formulas for propellers for the rate of change of side-force coefficient with angle of yaw and for the rate of change of pitching-moment coefficient with angle of yaw. Charts of side-force derivatives are given for two propellers of different plan forms.

Report presenting a series of tests made in the 15-foot free-spinning tunnel to study the spin characteristics of a model of a hypothetical canard airplane, which was designed to be about the same size and have the same general aerodynamic characteristics as a Boeing B-247 airplane. The model spun normally and had excellent recovery characteristics.

Report presenting measurements made of the pressures of the tail surfaces of the Republic Aviation Corporation P-47B airplane in the full-scale tunnel. Pressures were measured over the horizontal and vertical tail surfaces for several angles of attack and angles of yaw with numerous control-surface deflections to provide a check on the design loads. Results regarding the normal-force coefficients and predictions of forces on horizontal tail surfaces are provided.

Report presenting an investigation to develop an instrument for the determination of rain densities in this range in flight. The major requirements for the instrument are ease of operation, minimum weight and bulk, rapid response, and simplicity of installation.

Report presenting performance data on a Trane exhaust gas and air heat exchanger. Heat transfer rates were measured using specified exhaust gas rates and ventilating-air rates. The measured thermal outputs and static pressure drops are compared with predicted magnitudes.

Report presenting a detailed method for determining the jet-boundary corrections for reflection-plane models in rectangular wind tunnels. The principal effects of aerodynamic induction and boundary-induced curvature of the streamlines are considered. An example is included to illustrate the method.

"General relationships for the lead susceptibilities of paraffins, cycloparaffins, and olefins are presented. Methods are described by which the lead response may be estimated for these hydrocarbon classes, whether the lead response is indicated by octane number, critical compression ratio, or indicated mean effective pressure as limited by knock" (p. 1).

"A method is developed for calculating the performance of a dual-rotating propeller from the section characteristics of the blade elements. The method is applied to an eight-blade dual-rotating propeller and the computed results are compared with low-speed wind-tunnel tests of the same propeller in both the tractor and pusher positions. The computations are found to agree within the experimental accuracy of the measurements" (p. 1).

"The thrust produced by a variety of exhaust stacks and nozzles, and the effect of these stacks and nozzles on the power of a single-cylinder R-2800 engine were investigated over a wide range of engine speeds and manifold pressures in a series of tests in the Pratt & Whitney experimental test department. From the data obtained it is possible to estimate the optimum form of nozzles and the available thrust for airplanes fitted with R-2800 engines under sea-level conditions" (p. 1).

Report presents and discusses the improvements in hydrodynamic and aerodynamic performance of a seaplane with a retractable planing flap instead of a conventional main step. A type of flap that could be used is described and tested for hydrodynamic stability. Results regarding the trim limits of stability, limiting positions of the center of gravity, and skipping are provided.

"The results of a series of tests to determine the effect of internal pressure on the buckling load of a thin cylinder under an applied torque indicated that internal pressure raises the shear buckling stress. The experimental results were analyzed with the aid of previously developed theory and a simple interaction formula was derived" (p. 1).

Report includes tension fatigue test results on the following types of samples of 0.040-inch alclad 24s-t: (1) monoblock sheet samples as received and after a post-aging heat treatment, (2) "sheet efficiency" samples (two equally stressed sheets joined by a single transverse row of spot welds) both as received and after post-aging, (3) spot-welded lap-joint samples as received and after post-aging, and (4) roll-welded lap-joint samples. (author).

Report presenting the results of tests of a circular fuselage with various combinations of tail lengths and vertical tail surfaces with and without the horizontal tail surface in the 6- by 6-foot test section of the stability tunnel in the form of diagrams of variation of coefficients of lateral force and yawing moment with angle of yaw and angle of attack.

Report presenting an investigation to determine the knock-limited performance in a full-scale aircraft-engine cylinder of leaded blends of 10 pure hydrocarbons and a base fuel.

"Strain surveys were made on the stringers reinforcing a D-section box loaded in torsion and restrained from warping at the root. On the basis of the tests, a procedure is suggested for estimating the bending stresses due to torsion that occur near the flange of a D-section box. A similar test of a triangular-section box showed that for such a section there were no significant bending stresses due to torsion, a fact which was also shown theoretically" (p. 1).

"The design of curved sheet panels to resist shear involves a consideration of several factors: the buckling resistance of the sheet, the stress at which buckling becomes permanent, and the strength which may be developed beyond the buckling limit by tension-field action. Although some experimental as well as theoretical work has been done on the buckling and tension-field phases of this problem, neither of these types of action appears to be very well understood. This report presents the results of the first series of torsion tests of stiffened circular cylinders to be completed in connection with this study at Aluminum Research Laboratories" (p. 1).

Report presenting the results of aerodynamic tests of seven-blade propellers which were considered as a possible arrangement to avoid vibration difficulties. Variations of relative blade angle and rotational speeds of the front and rear components of a six-blade dual-rotating propeller were also investigated.