Investigation of aqueous and steam corrosion at elevated temperature has been carried on at Hanford for several tears. A number of reports have been published on various phases of the corrosion program but, except for monthly reports, little has been written on the progress of the Corrosion and Coatings Operation alloy development program. This interim report will outline the more important current phases of the aluminum alloy program.

In early July, 1958, it appeared that Columbia River temperature at HAPO would be near 24.5ºC by the end of August. River temperature were averaging 4º to 5º above 1957 figures and were 3º to 4º above the ten year highs. It seemed desirable to examine the problem to determine if any corrective measure could be taken, since it was apparent that production losses were imminent.

From objective: "The objective of this work was to design, develop, assemble, and test and automatic analyzing monitor for recording the prominent isotopes in reactor effluent cooling water."

Interest has been expressed in continuously monitoring the beta activity of the uranyl nitrate solution pumped to the RCU receiver tank, to facilitate operation at higher flow rates and with younger feeds. A beta scintillation detector has been developed which should make this feasible, and it is proposed that it be tested on stream for this use.

Because of the excessive vertical fragility and high replacement costs of mice-window G-M tubes used in vertical and horizontal lead-pig shelf counters, it was requested that a simple system of conversions to reliable scintillation detection be accomplished.

Introduction: "A limited test progress for the evaluation of type 347 stainless steel pipe which failed the Huey (?) test has been complicated. The tests reported herein were similar in scope to those reported in document number EW-20765, Corrosion Tests on Stainless Steel Plate, Waste Metal Recovery Process. Material tested was obtained on order number EWC-8553, National Tube Company Heat #3X9741. Lots 9789 and 9790."

The following report provides results from laboratory tests on the corrosion resistance of various types of stellite facings on astenitic stainless steel T-347 to Redox streams.

Report containing the procedures and results of tests made to determine the corrosion resistance of materials in a simulation of Hanford Laboratories' N-Reactor secondary system water environment.

The HAPO Critical Incident Alarm, Model I, is an instrument designed to give an audible and visual alarm signal in the event of a critical incident to which it is exposed. There will be thirty-one (31) of these instruments installed and several spares located in the various manufacturing buildings in the Chemical Processing Department where there exists any possibility of a critical incident occurring. The instrument is intended as a post or after-the-fact warning device. It will offer no protection prior or leading up to, nor prevent, a critical incident. They are intended to be operated from the 115 V. A.C., 60 C.P.S. emergency line power. The instrument is self-contained, including the radiation detector, and will be calibrated to alarm at 500 mr/hour in a gamma field.

The decontamination of portable instruments by the Calibration Unit has presented a problem for some time. Most of the contamination is in the 100 to 500 c/m or 500 to 2000 d/m range. Higher levels of contamination can usually be reduced to these levels, but further cleaning proves quite difficult

Description of Purex plant process for irradiated uranium for the separation and decontamination of plutonium and uranium from each other and from fission products.

Describes the design criteria, design details, and final installation of a high precision temperature and intimate contact monitor.

During the period when the writer mixing fuel element was being evaluated, a small Litton glass lathe and a General Electric Fillerarc welder were used to weld the mixing spool to the fuel element. Due to the condition of these units and to the numerous difficulties encountered with them, it was deemed necessary to design and procure a semi automatic welding unit which could weld in excess of three hundred fuel elements per day.

Abstract: "A titrimetric method for the determination of fluoride in plutonium is reported. Prior to a steam distillation of the fluoride, the bulk of the plutonium is separated by precipitation of the sulfate. The fluoride in the distillate is titrated at a pH of 3.2 with 0.001 M thorium nitrate, using chrome azurol-S indicator. Applied to samples containing 1 to 15 parts per million fluoride, the recovery is 87% and the precision on the 95% confidence level is +/- 0.65 ppm."

The major portion of transfers and inventory in the Chemical Processing Department are dependent on volume measurement. Good volume measurements are therefore essential to good SS material control. Considerable attention has been given to the volume problem especially on primary transfer points. Document HW-57888 discusses the biasing effect pf temperature on manometer oil. HW- 57866 given the procedure for vessel calibration. Other undocumented correspondence has discussed recent calibrations and certain aspects of temperature considerations in the volume determinations. However, there is a need to document for future reference the consideration given temperature and provide at the same time information which covers the temperature angle on all volume methods used in the Chemical Processing Department.

The measurements reported here are companion measurements to those reported earlier in HW-63585. The only significant difference between the measurements is that 1.8 w/o enrichment UO2 fuel was used for the first set, and 2.6 w/o enrichment UO2 fuel was used for the measurements described in this report. The new results will be presented graphically, and for completeness, the details of the measurement will be included here as well as in HW-63585.

Objective: "The laboratory equilibrium study RC-E-1 described in this report was carried out to obtain uranium equilibrium curves at various concentrations of nitric acid and of TBP."

A number of the questions which have been posed to us in the subject references are commented upon below. These have been reviewed by personanel of the Research and Engineering Operation and the Facilities Engineering Operation, Chemical Processing Department, and of the Chemical Research and Development Operation, Hanford Laboratories Operation. Particular acknowledment is given G. J Alkire, J. P. Duckworth, J. B. Fecht, R. G. Geier, E. R. Irish, H. M. Jones, G. C. Oberg, A. M. Platt, W. H. Reas, W. C. Schmidt, R. J. Sloat, W. H. Swift, M. T. Walling and L. L. Zahn of these organizations for assistance given assembling this information.

From introduction: "This report is concerned with exploratory experiments designed to studies the efficiency of a number of scavengers for zirconium and niobium adsorption and to provide preliminary information on the best conditions to employ on the most satisfactory of those scavengers studied, namely Super Filtrol FO. The data in this report include data obtained through October, 1949, and are by no means considered to be final. The investigation is currently being actively continued."

The following report describes a chemical procedure to analyze fission products and long-lived rare earths in both untreated urine samples and the supernates from the precipitation steps in the TTA procedure for plutonium.

The final percentage of xenon created by fission in uranium and plutonium is a function of the neutron flux intensity. The flux dependence results because axenon 133 and 135 can be converted to a a stable xenon isotope by neutron capture instead of decaying into cesium.

Report reviewing literature that concerns "the compatibility of stainless steels and nickel-base alloys with various gases which might be present in or around a high temperature nuclear reactor" (p. 2).

The remodeling, fabrication, and instrumentation of a high vacuum system are described. The faults encountered with the old system and their solution are outlined. Tests were made on diffusion pump oils and on the reduction of pump oil back diffusion. The measurement of high vacuum pressures by a cold cathode ionization gage at various points on a vacuum system are discussed.

Hastelloy F is a prime contender as a material of construction for plant dissolvers in the power fuel reprocessing program. Consequently, the fabrication and installation of dissolver was undertaken to delineate any unknown problems associated with the use of Hastelloy F; and, at the same time, to provide a vessel for development studies on the Niflex or the Sulfex processes. The purpose of this report is to describe the actual basis for design as well as to present the problems encountered during the fabrication of the vessels.