The following report analyzes the characteristics of eight chelated uranium complexes and seven uranium ammines, prepared from the reaction of organic solutions of uranium salts with complexing agents and organic bases.

This quarterly progress discusses the ongoing work at the Oak Ridge National Laboratory for the quarter ending in March 10, 1952. Topics discussed include reactor theory and design, shielding research, materials research, and includes appendixes with supplemental information.

The angular distribution of fission fragments from the neutron-induced fission of several isotopes has been studied. Distributions were observed for thermal neutrons on U233 and U235, Lady Godiva leakage neutrons on U235 and U238, and 14 Mev neutrons on U233, U235, U238, Th232, and Np237. No anisotropy was observed for thermal neutron fission, whereas for Lady Godiva neutrons and 14 Mev neutrons the probability of fission along the axis of the neutron beam was determined to be higher than for fission in the orthogonal direction. Experimental results are given on pages 10 and ll.

The following report follows the studies of electroplating on uranium and concurrent metallurgical clodding.

"In order to determine the factors involved in the scale-up of cores with concentric inlet and outlet pipes, a 48 inch carbon steel flow model, geometrically similar to a 6 foot diameter core, has been assembled and tested...Visual studies were made of dye and gas behavior in the sphere, and quantitative measurements of point residence times were obtained through the use of conductivity cells actuating a Brush recorder. Static pressure drop across the core was measured."

When water is used as a coolant in any heat-producing process, the purity of the cooling water is of considerable importance, both from the standpoint of build-up of deposited solids inside the cooling tubes, and as an indication of corrosion of the tubes or any other materials with which the water comes in contact. The first problem has long been recognized, and is generally solved by pretreatment of the water. Efficient treatment can reduce the total solids content to less than 0.1 ppm, and the concentration of individual elements to the order of 0.01 ppm. If water of this purity is used, the analysis of the input and output stresses can result in some useful information. The input stream analysis, of course, is direct measure of the quality of the original cooling water, and frequent analysis by a reasonably fast method can be used to keep pretreatment under control. But of even greater significance is the difference in the impurity content of input and output streams. In a simple, straight-through system the difference generally will be negligible. If a closed, recirculating system is considered, however, with the coolant water circulating through the process to be cooled and then through a …

Twelve uranium-magnesium fuel material samples have been irradiated in the MTR at the request of the Pile metallurgy Unit. These samples were 0.40 inch in diameter by 1.5 inches long and were canned in Zircalloy-2 capsules. The uranium used in these specimens was in the form of chips which packs about 50 volume percent. Six of the samples contained a matrix of pure magnesium and the other six contained an alloy matrix of magnesium - 1.4 weight percent silicon. Two specimens of each matrix material were irradiated to 1000 MWD/T and a like number to 5000 MWD/T. Bend tests were performed on the samples and on unirradiated control samples to secure a measure of the effect of radiation exposure on the physical properties of the material.

Introduction: This report is principally concerned with analysis of measurements taken on the APPR-1 core during the course of the extended Zero Power Experiments (ZPE-2). The bulk of these measurements are reported in APAE No. 21. There are some additional measurements reported in APAE Memo 115. In addition to the analysis of the ZPE-2 data some re-evaluation has been made of a few of the results obtained from the first set of Zero Power Experiments (ZPE-1). The ZPE-1 measurements are reported in APAE No. 8. During the course of analysis work it became apparent that a considerable amount of basic experimental data had been taken on the APPR-1 core. It seemed worthwhile to organize this report in such a fashion that other investigators could make maximum use of this data. It provides excellent opportunity for individuals and groups interested in basic reactor reactor analysis problems to check calculational techniques. An attempt has been made to include all of the fundamental information concerning the material content and geometry of the APPR-1. This material is in included in the Appendices. In addition, cross-section files and group constants have been listed rather extensively in order that other investigators could compare results presented in …